Search Documents

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

By V. N. Medvedev, A. M. Bryukhanov

Stationary mine air control equipment enables monitoring of CH4 concentration only in sensor locations. CMC-4 individual indicator built into a caplight has been developed in Ukraine, extending CH4 monitoring to manned job sites. Major technical characteristics of the indicator are demonstrated. It features two operation thresholds: 1st threshold 1.0 to 2.0% vol. 2nd threshold 1.5 to 2.5% vol. Basic absolute accuracy ± 0.2% Caplight battery is a common power supply for the lamp and CH4 indicator, providing at least 10 hours of the system non-stop operation. Average pre-failure life is at least 10,000 hrs. It features: an explosion proof design and intrinsically safe test circuit; a small-sized sensor as an integral part of the caplight; a hybrid microcircuit to facilitate functioning of methane monitoring unit. The CMC-4 indicator weight is the weight of the caplight itself and equals 2.4 kg. A two-threshold design makes possible to distinguish between methane sources: slow accumulation due to diffusion or sudden rushes due to a gas-dynamic event. CMC-4 indicators in addition to stationary equipment minimize the risk of CH4 explosion underground determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By B. P. Watson

The Bushveld platinum group metal deposits in South Africa are the largest in the world. These deposits occur as two distinct stratiform tabular ore bodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2300 m. The mining method is a variation of planar open stoping. Crush pillars are widely used to support the open stopes. These pillars are designed to fail and the residual strength provides the required support resistance to stabilize the stoping excavations. This paper describes the in situ measurement, of stress within a Merensky pillar from Impala Platinum. These measurements were used to derive a stress-strain curve that includes pre and post failure behaviour. 2D FLAC modelling, with strain softening, was done to investigate how damage expands into the hanging- and/or footwall. Although the so-called ?squat? effect is always present, the modelling suggests that it does not dominate the pillar system behaviour at larger width to height ratios. Punching of the pillar into the hanging- and/or footwall increasingly controls the pillar system behaviour with larger width to height ratios. The paper investigates the behaviour of a system that incorporates the immediate hanging- and footwall, as well as the pillar itself.

Jan 1, 2009

By K McLeod

{Figure 1} The Placer Dome-Western Areas Joint Venture?s South Deep Twin Shaft Complex, has been planned and dreamt of for nearly 20 years. [ ] The gold reserve at the bottom of these shafts is one of the largest single intact gold deposits remaining in the world today, containing an estimated 57 million ounces. This is about the size of the fictitious reserve created by inventive prospectors for the infamous BREEX scam in Kalimantan about ten years ago and about the size of the reserve Harmony claims as its own in it?s current hostile takeover bid for Gold Fields. So it is certainly of the magnitude that dreams are made of. [ ] {Figure 2} The unique orebody lies in a continuous, highly concentrated, thick deposit, an estimated twelve kilometres along dip and a two kilometre wide strike. Due to the thickness of some sections of the reef, up to 60 metres in places, bulk mining methods will be required for it?s extraction. [ ] {Figure 3} The twin shaft system comprises a main shaft which had an initial design depth of 2765m and a ventilation shaft of 2760m, making them the world?s deepest to be sunk in a single lift. The shafts were

Jan 1, 2005

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

By S. L. Crouch

A. C. Dieringt The procedure described by Professor Crouch for the modelling of mining in faulted ground allows the elastic and inelastic deformation to occur simultaneously, that is, fault slip occurs while an element is being mined. The energy release rates (ERR) shown in Crouch's Fig. 10 are apparently calculated from his equation 9 using the i total deformation Din (see the upper load line of Fig. I) Refractories The institute of 'Gesteinsh iittenkunde' of the technical university at Aachen, the Refractories Research Institute at Bonn, and the Verein Deutscher Eisenshiittenleute (VDEh) at Diisseldorf are to hold the XXII International Refractory Colloquium on 27th and 28th September, 1979, at Aachen.

Jan 1, 1979

By A. N. Brown

Rock breakage by drilling and blasting is fundamental to every hard-rock mining operation. The subject was an apt choice for a mining school because many technological changes have taken place since the subject was last presented some ten years ago. However, because of the development of surface mining, it was decided that two schools should be held: one for underground mining, and the other for surface mining. The School on Underground Mining was held at the University of the Witwatersrand in February 1986.Copper 87 COPPER 87 is an international conference organized by metallurgical and academic institutions of two of the largest producers of copper in the world, Chile and Canada.

Jan 1, 1986

By B. K. Loveday

The use of large flotation machines is well established, resulting in substantial savings in both capital and operating costs. Therefore, when a new plant is designed, laboratory and pilot-plant tests should be used to simulate large flotation cells, or appropriate scale-up factors should be employed. 'Conference on titanium The Fifth International Conference on Titanium will be held from 10th to 14th September, 1984, in Munich, West Germany, organized by the Deutsche Gesellschaft fur Metallkunde e.V., in association with the American Society for Metals, Societe Francaise de Metallurgie, The Academie of Sciences U.S.S.R., The Japan Institute of Metals, The Metallurgical Society of A.I.M.E., and The Metals Society.

Jan 1, 1983

By A. B. Stewart, I. J. Barker

Traditionally it has commonly been believed that the only problem with inductive reactance in a submerged-arc furnace is that it leads to difficulties with the electricity supply as a result of the Iow power factor. This paper sets out to show that inductive reactance can also give rise to the following problems in the metallurgical operation of a furnace: (i) dead and live phases (fairly well known in openarc furnaces), (ii) lack of sensitivity to electrode movement, (iii) interactions between electrodes. These problems increase with increasing inductive reactance relative to resistance, and thus they increase with furnace size. Each of these effects is discussed in detail, and suggestions are made for their alleviation.

Jan 1, 1980

By J. A. C. Diering

The determination of stresses and displacements close to tabular excavations is of considerable importance in the planning of tunnels and of remnant and pillar layouts. This paper gives a description of a simple yet effective method for the achievement of improved values from an analogue or MINSIM type of analysis. Essentially, closures and rides (the movement of hanging-wall relative to footwall) in mined-out areas are assumed to vary in a piecewise linear fashion as opposed to a piecewise constant fashion. As the former fashion more closely resembles the true variation, it is possible for the stresses and displacements at points close to the excavations to be calculated with much better accuracy.

Jan 1, 1980

By D. G. Keefe, I. C. Robinson

In this paper the authors present their views on the actual and potential role of commodity analysis in mining industry. Owing to the dominant influence of the economy on all commodity markets, it is essential that individual commodities are studied not only in depth but within the broader context of economic influences. A commodity unit, which monitors market developments in a wide range of commodities, is well placed to provide the broader perspective in the study of commodity markets. This paper describes some of the specific functions of such a unit. Some of the methods used for price forecasting are described, and the results of price forecasts by different forecasting methods are compared.

Jan 1, 1980

By D. Gerhart, J. Hung, J. Hackwood, A. Pix

A computer-based, real-time mine management system has been installed in a number of underground operations. The system’s innovative software application is coupled with wireless data acquisition and database management to provide complete mine monitoring and control execution in closed-loop control fashion. The system is well suited to automatically assign equipment, acquire status, and reassign resources based on status; and to automate information handling. The system has provided mines with improved utilization of the equipment fleet and mining crews, and reduced workplace cycle time. This paper describes the deployment of systems at a number of underground mining operations and discusses future development of the system. Keywords: Computer-based: Real time: Utilization: Mining cycle control: Monitoring: Productivity

Sep 1, 2001

By N. Thorp, S. J. Bluhm

It has long been recognized that the provision of an acceptable thermal environment minimizes the danger and the adverse effect of heat stress, which is directly linked to decreased productivity, increased accident rates, and excessive physiological strain in workmen. Refrigeration in one form or another helps to provide this acceptable thermal environment. This paper outlines the problems encountered in a working area, and the steps taken to alleviate environmental conditions in some stopes with the introduction of selective cooling employing small water-chilling units in conjunction with specially designed stope coolers. Performance figures are given for plant and stope coolers, and the effectiveness of the system is assessed from an evaluation of the improvement achieved in the environmental conditions.

Jan 1, 1986

By J. N. van de Merwe

CONTRIBUTION BYH. WAGNER AND T.T. OZAN The paper by Dr J.N. van der Merwe makes an important contribution to the design of bord-and-pillar workings in the Vaal basin. It has been recognised for some time that the strength of coal seams in the Vaal basin is markedly lower than that of coal seams in other coal-mining districts in South Africa. However, there was insufficient data to quantify how much weaker the extensively jointed coal the Vaal basin is. A number of recent pillar collapses that occurred at Sigma colliery, the only remaining underground colliery in the Vaal basin, provided Dr Van der Merwe with an opportunity to make this assessment.

Jan 1, 1993

By C. J. Fauconnier

The various methods of detecting fires and heatings in collieries are reviewed. The methods described range from those relying principally on human senses to sophisticated methods employing infrared technology to detect traces of the products of oxidation and combustion. The advantages and disadvantages of various gases employed as indicator gases for the early detection of heatings and fires are discussed, and recommendations are made in this regard. The operation of a modern infrared carbon monoxide detection system is described, and the differences in operation and application of telemetric systems, tube-bundle systems, and up cast-shaft monitors are discussed In conclusion, some indication is given of the capital outlay required for typical early-detection systems.

Jan 1, 1981

By M. J. Southwood

SYNOPSIS Experiments carried out under atmospheric pressure and temperature (25°C) and sterile conditions show that the dissolution rate of nickel and copper from a pyrrhotite-pentlandite-chalcopyrite ore in a lixiviant of sulphuric acid is greatly enhanced in the presence of pyrite. At a pH value of 1,8 and in the presence of pyrite of equal mass to that of the ore, the recoveries of nickel and copper improved dramatically (21 and 80 per cent respectively). At a pH value of 4,0 the recovery of nickel was enhanced, but the chalcopyrite was refractory. A galvanic mechanism is probable, but cannot be proved from these experiments. The economic implications of the results are discussed.

Jan 1, 1985

By T. Vincent, J. Steele, C. Debrunner, M. Whitehorn

This paper presents current work on the development and use of stereovision for underground mining. Information on the calibration of the cameras and the feature-matching algorithm are presented. This system uses an intensity-based approach that evaluated correspondences along the epipolar line. Once features have been identified and their distance from the cameras computed, a three-dimensional map of the muck pile is developed. The approach used here uses a ray-tracing algorithm. This approach provides an uncertainty measure along with the elevation. A discussion of the use of this modelling information in the control of the LHD is included. Keywords: Robotics, automation, LHD, underground mining, vision sensing, task automation, tele-operation

Sep 1, 2001

By G. G. Stanley

Mechanisms in the autogenous mill and their mathematical representation by G. G. STANLEY, B.Sc. (Eng.) (Wits.), M.E. (Queensland), Ph.D., (Fellow) The special characteristics of the autogenous mill are stated, and a suitable type of model for the mill is presented. Details of the test plant and experimental techniques for obtaining the data for model development are next given. followed by a discussion of the methods developed for the computation of the model parameters, namely the appearance matrix, the abrasion and crushing breakage-rate functions, and the discharge-rate function. Examples of results obtained with the model are given, and finally there is a brief account of confirmatory work on a fullscale autogeneous mill.

Jan 11, 1974