Search Documents

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

Discussion H. J. S. Kriek*: During 1956 Iscor became interested in the acid smelting in a blast furnace of siliceous ores containing 15 per cent silica. This interest was as a result of the successful acid smelting in Germany at a CaO/SiO2-ratio of between 0.4 and 0.8. Acid smelting can become an economic proposition due to a reduction in slag volume accompanied by a lowering of the coke rate. Paschke and Hannel1 found that a free flowing slag (i.e. viscosities of less than two poise) would not be obtained at C/S-ratios lower than 0.82 and that the addition of 3 to 4 per cent alkalies became necessary. In titanium bearing slags it was established that maximum fluidity is obtained with 10 per cent TiO2. Acid smelting resulted in increased sulphur pickup with decreasing O/S-ratio and desulphurization with soda-ash outside the blast furnace was necessary. At Iscor Mr B. B. Segal established that, for slags with (CaO+MgO)/SiO2-ratios of 0.5, 0.6 and 0.7, the addition of alkalies and TiO2 resulted in a substantial decrease in melting point and also of viscosity. At a (CaO+ MgO)/ ratio of 0.53 the addition of 10 per cent TiO2 is as effective as the addition of 3.75 per cent alkalies. This means that a blast furnace can be run without the addition of alkalies and consequently the detrimental effect of alkalies on the lining can be avoided; also that fluid slags with 5 to 15 per cent MgO and 8 to 10 per cent Al203 can be obtained with 10 per cent TiO present. (CaO+ MgO)/SiO2-ratios smaller than 0.5 the addition of titania resulted in a decrease in melting point and also in an increase in viscosity. In ceramic crucibles the slag did not become more viscous with time but thickened appreciably when held in graphite crucibles. No titanium carbonitride could be detected and only Ti20a was found. Prof Howat also did not obtain the TiC-TiN solid solution and therefore it appears that the thickening of the slag is not solely due to the formation of the titanium carbonitrides. This is in agreement with the work of Michailov and Belyakova2 who found that TiO2 decreased the viscosity of acid slags and increased the viscosity of basic slags; that titanium sesquioxide (Ti203) and titanium monoxide (TiO) increased the viscosity of both acid and basic slags and that titanium carbide, which is found in larger amounts in basic slags than in acid slags, considerably increases the viscosity of both acid and basic slags. Patzak et al3 describes the following oxygen deficient titanias, viz Ti2O, TiO, Ti203, Ti3O5, Ti4O7, Ti5O9, Ti6O11- Ti10O9,Ti7O13,Ti8O15 and Ti9O17. Until about 1959 a fair amount of data was available on the viscosity of normal slags to which titania was added2, 4, 5, 6, 7, 8, 9. At Iscor an electromagnetic viscometer based on the viscometer developed by Bockris10 was built. Progress was very slow as our main attention was centred around problems associated with the operation of the Rotor process. During 1962 and 1963 two papers containing fundamental work on the viscosities of slags in the systems CaO-SiO2-TiO211 and CaO-SiO2-TiO2 at 0 per cent A1203, 10 per cent Al203 and 20 per cent Al20312 appeared. The work of Ross and Ohno obviated the necessity of any further work by Iscor on the viscosity of blast furnace slags containing titania. Ross gave the following optimum compositions for blast furnace slags containing titania. Titania % Lime % Silica % Lime/Silica-ratio 20 30-42 38-50 0.6-1.10 30 27-36 34-43 0.63-1.06 40 24-32 28-36 0.66-1.14 The optimum temperature is 1,500°C because at this temperature the largest workable composition range exists. Higher temperatures result in narrower optimum composition ranges and in increased rates of thickening. The factors affecting the rate of thickening were also investigated by Ross and Ohno, as the main problem with slags containing titania is not finding compositions which are fluid at operating temperatures but the thickening due to a lack of oxygen. With these slags when there is insufficient oxygen to co-ordinate each silicon atom with its own individual shell of four oxygen ions, some sharing of oxygen ions must occur, resulting in the formation of large silicate ions and a rise in viscosity. The formation of oxygen deficient titania can be prevented as long as iron oxide or manganese oxide remain in the liquid slag. Iwase13 and also Viens, Camp bell and Rogers14 obtained in the experimental smelting of ilmenite ores fluid slags with more than 3 to 5 per cent manganese oxide and ferrous oxide in the slags. It appears that titaniferous ores can be smelted in blast furnaces under the following conditions: (1) Acid slag operation, i.e. at C/S-ratios from O.6-1.0. (2) Dolomite can be used as a flux as MgO is a network modifier. (3) The Al2O3-content must be less than 15 per cent as alumina promotes thickening of the slag and decreases the optimum composition range. (4) The hearth temperature must not exceed 1,500°C. According to Ross a definite amount of energy is required for each ton of iron produced and in order to increase production an increase in heat

Jan 6, 1969

By Mike Stanley

This is a case study of an opencast coal mining operation where the physical and financial performance was improved via applying a process of transformational leadership development. [ ]

Jan 1, 2008

By M. Visser

Keywords: Pyrometallurgy, furnace, ferrochrome, Samancor, ferrochrome process Samancor Chrome has been, and continues to be, a major player in ferrochromium production. The company has a proud history and possesses benchmark technology and operations. Currently five business units are operating: two sets of mines and three smelter plants. Samancor Chrome produces around one million tons of charge chrome annually. Chrome ore, intermediate-carbon ferrochrome, and low-carbon ferrochrome, form part of the portfolio. Electrode paste is also manufactured through a joint venture with Highveld Steel and Vanadium. Samancor Chrome has a balanced approach towards operational strategy, and has entered into a number of joint venture partnerships. Through its access to quality raw materials, knowledge, and experience of various production technologies, and its strategic abilities, Samancor Chrome is well positioned to reap the benefits from opportunities in the current and future industry context.

Jan 1, 2006

By C. Dauber

Implementing new technologies in industrial operations entails the challenge of measuring the improvements gained by the applied technology. Nevertheless, it is absolutely essential to assess the technical and economic benefits in objective and comprehensible numbers to create a platform for further management decisions. Underground coal mines are characterized by numerous, quite complex procedures which make it difficult to determine the specific economic benefit of a new machine, technique, or method. In the OPTI-MINE Project funded by the European Union?s RFCS programme, five underground coal mines applied the latest information and communication technologies (ICTs) to improve efficiency, mine safety, occupational health, and environmental im-pacts. An integral part of the project is the assessment of these technologies by using key performance indicators (KPIs). The paper will describe some examples of the selected KPIs and the preliminary findings.

Jan 1, 2014

By Yijun Caoa, Xiuxiang Taoc, Zhongbo Hub, Yinfei Liaoa

A new preparation scheme for a difficult-to-float coking coal from the Kailuan Mine, Tangshan, China was investigated. The results showed that grinding followed by column flotation was beneficial for obtaining products with low ash content. The positive effect of grinding on the coal floatability is attributed to the liberation of intergrowths and coal surface improvement. Tests indicated that 10 minutes was the optimum grinding time, and over grinding resulted in a deterioration in flotation performance. With a grinding time of 10 minutes, conventional flotation had potential to yield a product with around 12.42% ash content and 69.15% combustible recovery. Column flotation can reduce the product ash content to 11.15%and increase combustible recovery to 74.47%. Consistently better flotation results reveal that column flotation is more efficient than conventional flotation for such fines.

Jan 1, 2015

Control of flotation processes is mostly managed by plant operators, who assess the performance of the plant based on their own experience and other heuristic rules. These rules tend to be subjective or ill-defined, since most of them are concerned with the structure of the flotation froth, such as colour, bubble size and shape distributions, froth mobility and froth stability. These phenomena are very difficult to quantify objectively, and inexperience on the part of the operators, human error, etc., can lead to significant inefficiencies in plant operation. In this paper the development of a fuzzy system to support the control decisions of plant operators is described, which leads to significantly smoother control action and more stable plant operation than could be obtained with crisp sets of rules or manual control strategies. Keywords: flotation, fuzzy logic, image analysis, genetic algorithms, rule induction

Jan 1, 2000

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

By A. Ward, A. Smith, D. Harpley

Methods for the prediction of seepage quality from waste-disposal facilities are evaluated for input to the design of desalination treatment facilities. This is done by reference to a waste dump seeping into a near-surface aquifer, the contaminated seepage being collected by scavenger wells. As the quality of contaminated water intercepted by the wells will vary with both space and time, it is necessary for predictive methods to accommodate such variations. One-dimensional and two-dimensional predictive solute transport models are described and applied to the seepage and scavenger-well example mentioned above. The advantages and disadvantages, interims of overall applicability, data requirements, and possible accuracy, are described and discussed. While one-dimensional models have the advantages of speed, simplicity, and cost, the frequent requirement of prediction in both space and time necessitates more complex, two-dimensional simulation.

Jan 1, 1987

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By D. G. Krige

By use of models based on the South African gold-mining industry, analyses are made of the effects of changes in the mining tax structure on the .State's tax income from potential new mines; also on the percentage of such mines likely. to be proceeded with. The percentage is affected by the correlation between changes in taxation and in the flotation pay limits !or new mines. It is shown that the State stands to gain both directly and indirectly from raising the level of the capital allowance and from its extension to all mines; and that the reduced taxation resulting from a lowering of the discriminatory high tax formula for the gold mines, would, in respect of potential new mines, be compensated for by a significant increase in the percentage of such mines that would be proceeded with.

Jan 1, 1979

By R. P. Plasket, D. A. Ireland

Ancillary smelter operations and sulphuric acid manufacture at Impala Platinum Limited by R. P. PLASKET. Pr. Eng.. M.Sc. (Chem. Tech.). Natal (Fellow) and D. A. IRELAND. Pr. Eng.. B.Sc. (Chem. Tech.). Natal (Member) The de-watering, spray drying, and converter operations at Impala are described, aspects that may be new to the minerals industry in South Africa being elaborated. Air-pollution control necessitated the installation of a sulphuric acid plant to limit the emission of sulphur dioxide to the atmosphere. Closer control of the smelting and converting operations was required for successful operation of the acid plant on the inherently Iow and varied concentration of feed gas from converter blowing. Approximately 82 per cent of the sulphur entering the smelter is converted to sulphur dioxide, of which 67 per cent is fed into the sulphuric acid plant.

Jan 8, 1976

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By M. Kannenberg

When coal properties are estimated geostatistically for mine planning in the hardcoal industry, there is one important supposition which influences the reliability of prediction of economically profitable parts of the deposit. This is the fact that activities in hardcoal exploration and mine planning are characterized by distinct levels of information and knowledge upon which decisions of economic import must be based, for example, whether exploration should proceed or not, or which methods and strategies should be used to maximize search efficiency. To get more reliable results for mine planning, in particular, advanced kriging methods (e.g. conditional simulation) have to be introduced and checked for their reliability in historical analyses (post-mortem studies). By using this feedback, kriging results from underground samples or production data can be compared with results gained by advanced geostatistical methods from exploration boreholes.

Jan 1, 1987

By F. A. G. M. Camisani-Calzolari

The uranium production forecasting program described in this paper projects production from Reasonably Assured, Estimated Additional and Speculative Resources in the cost categories of less than $130/kg U. Originally designed to handle South African production, it has been expanded and redimensioned using available published information to forecast production for countries of the Western World. The program forecasts production from up to 400 plants over a period of fifty years and has built-in production models derived from documented historical data of the more important uranium provinces. It is particularly suitable to assess production cavabilities on a national and global scale where variations in outputs for the individual plants tend to even out. The program is aimed at putting the uranium potential of any one country into a realistic perspective, and it could thus be useful for planning purposes and marketing strategies.

Jan 1, 1987

By E. B. Viljoen

I. R. M. Chaston* As a gravity concentration man in the midst of so many eminent flotation experts I feel like Daniel. However, I would respectifully disagree with the opening remarks by Mr Viljoen. First, he suggested that gravity concentration of cassiterite was not effective in sizes below 30 microns. In a paper to the Institution of Mining and Metallurgy in 19621, I gave some figures for gravity concentration of deslimed material both for cassiterite and for wolfram which indicated that careful shaking table concentration of fine deslimed material could give recoveries of 75 to 90 percent in the size ranges above 13 micron. These were figures obtained from normal plant operation. It would be interesting to know if any tests were carried out on gravity concentration of the efficiently deslimed feed to this flotation plant to see what the recovery would be. Secondly, Mr Viljoen suggested that gravity concentration plants were expensive. He gives the cost of a flotation plant at R300 000 to treat a feed of 400 t.p.d. to the desliming section or 160 t.p.d. to the flotation cells. From his operating cost figures it would appear that the flotation cost is approximately R2 to R4 per ton of feed to flotation and the total operating cost about R2 per ton of feed. A table plant to treat this tonnage of deslimed feed would consist of about 30 tables and should cost considerably less to install and very much less to operate than the flotation plant. Third, Mr. Viljoen suggests that the concentrate grade from a gravity concentration operation would be unacceptably low. The paper quoted abovel showed that once a primary fine concentrate had been made, giving a suitably deslimed material, further gravity concentration could give concentrates of over 40 per cent Sn with high recoveries. Tailing from this dressing stage was naturally returned to the feed. To give these high grades, sulphides had been removed by flotation but this necessary flotation step is simple and cheap to operate and could be restricted to the final stage when the quantities involved are small. I would agree that flotation has a part to play in fine tin recovery but this role would only seem to become fully effective at sizes below 10 micron and would seem to require, as Mr. Viljoen has suggested, a mechanism for sizing which is effective down to, say, 1 micron. In the meantime it would be interesting to try tabling the flotation tailing to see if it was possible to recover the plus 20 micron cassiterite which is not recovered well by flotation. One point which has been made during discussion is the suggestion that cassiterite particles have a fully hydrated surface at normal pH. I wonder if this layer could materially affect the overall specific gravity of a very small cassiterite particle and, if so, whether gravity concentration of the very fine cassiterite would be improved if carried out in acid conditions, which would inhibit the formation of this hydrated surface. REFERENCES 1. CHASTON, I. R. M. 'Gravity concentration of fine cassiterite'. Trans. Inst. Min. and Met. Vol. 71, p. 4, 1961 and 1962, and discussion of this paper. Dr. R. P. King Mr Viljoen has drawn attention to the difficulties associated with the presence of very fine particles in the flotation pulp and he has indicated that, on the Union Tin plant, they must sacrifice 30 percent of the cassiterite in the minus 7 /Lm material which they separate and lose. He has also indicated that the rate of flotation of cassiterite remained high at these small sizes. The problem arises because the very small particles stabilize the froth making it impossible to handle. These stable froths cannot be easily broken and therefore cannot be pumped and processed. It seems that further fundamental research work on the properties of stabilized froths is urgently required. We have found another difficulty associated with the presence of very fine particles in phoscorite slurries; these particles can be easily floated but with very poor selectivity. We believe that it is possible that a purely physical mechanism such as entrainment is responsible for the collection of fine particles in the froth. We have also demonstrated that the presence of fine particles in the pulp adversely affects the rate of flotation of the larger particles. For esample, we have found an increase in recovery of + 100 um material from 2 percent to 17 percent in a standard laboratory batch flotation test on phoscorite when the - 37 um was removed from the feed. Such interactions between particles are not universally recognised as an important aspect of the complex flotation mechanism. They should appear in any quantitative formulation of the flotation rate process.

By C. Erichsen, J. Werfling

ABSTRACT: A three-dimensional elastic constitutive model for rock salt is proposed. This stress strain law takes into account the three phases of creep (transient, steady state and accelerated creep), dilatancy, as well as the failure and post failure behaviour. The model was implemented into a finite element program and validated on the results of laboratory tests and in situ measurements. A good qualitative and quantitative agreement with the test and measurement results is achieved. A stability analysis for an underground repository in rock salt is presented. ZUSAMMENFASSUNG: Es wird ein dreidimensionales elastisch-viskoplastisches Stoffgesetz für Steinsalz vorgestellt. Mit diesem Stoffgesetz können die drei Kriechphasen (primäres, sekundäres und tertiäres Kriechen), Dilatanz sowie das Bruch- und Nachbruchverhalten erfaßt werden. Dieses Modell wurde in ein Rechenprogramm, das auf der Methode der finiten Elemente basiert, implementiert und an Ergebnissen von Laborversuchen und in-situ-Messungen validiert. Die Versuchs- und Meßergebnisse lassen sich mit diesem Stoffgesetz qualitativ und quantitativ gut nachvollziehen. Als Anwendungsbeispiel wird der Standsicherheitsnachweis für eine Untertagedeponie im Steinsalz erläutert. RÉSUMÉ: Cet article présente un modéle constitutive élastique/viscoplastique à trois dimensions pour sel gemme. Ce modéle comprend les trois stade de fluage (fluage primaire, secondaire et tertiaire), la dilatation, le comportement de défaillance et d'après défaillance. Il est implanté dans un programme de calcul aux éléments finis. À l'aide des essais laboratoire et des mésures in situ, le modéle a été validé. Les résultats des essais et des mesures concordent qualitatifs et quantitatifs aux résultats des calculations.

Jan 1, 2003

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003