Search Documents

By K. E. Mantell

1. TRACKLESS MINING AT OAMITES by K. E. MANTELL Oamites Mine, brought into production in late 1971, is located 50 km south of Windhoek, South West Africa, on the northern boundary of and just outside the Rehoboth Gebied. Oamites was known as a possible mining proposition at the turn of the century when Hanseatische Minen Gesellschaft was adit mining on the adjacent farm Kamzwas. Rand Mines Limited carried out a small amount of prospecting in the early 1960s, Falconbridge Explorations Limited later taking over the prospect. Approximately 4600 m of diamond drilling was carried out between 1965 and 1967.

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

By P. Kind

Design criteria and recent developments in large-capacity Wemco flotation cells by P. KIND, Ph.D. (Clausthal), B.Sc. (Visitor) The scaling-up of the large flotation cells that have been developed during the past few years has been based on hydrodynamic considerations and has resulted in a 500 ft3 cell unit. Plant results on a porphyry copper ore show that the 500 ft3 unit is equivalent to the previously used 300 ft3 model.. . Plant tests on the use of 300 ft3 flotation cells for the recovery of phosphate, particularly from the coarse size fractions, are also described.

Jan 3, 1976

By J. H. Bulloch

This paper describes detailed fractographic analyses of several specimens that had undergone corrosion-fatigue tests at high stress ratios in simulated pressurized water-reactor environments. The distribution and morphology of non-metallic manganese sulphide inclusions are shown to strongly affect the growth of environmentally assisted cracks (EAC), and certain features suggest that a hydrogen-assisted mechanism is responsible for the observed EAC growth. The incidence of transient EAC growth in isolated regions suggests that the critical conditions that trigger this type of growth are the 'right' local chemistry at the crack tips and imposed mechanical conditions.

Jan 1, 1987

With the increased variability of today's large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By M. Rossouw

The paper sets out the strategic importance of South Africa?s mining and minerals sector to the national economy. It relates how inexorable and accelerating urbanization and industrialization in emerging markets, especially in China and India, will translate into sustained demand for the minerals that South and southern Africa have in abundance. It warns that while countries buying raw materials from South Africa use these inputs as the basis on which to build value-added, employment-creating industries, South Africa is failing to exploit the economic benefits inherent in its mineral wealth, exacerbating its shortage of skills.

Jan 1, 2011

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By S. M. Rupprecht

"SynopsisOver the last decade in South Africa, there has been a significant increase in the number of mining operations, both open pit and underground, which use independent contractors to carry out mining activities. Often mine owners will choose the contractor option without fully understanding the consequences of undertaking this option. Traditionally, contract mining has come at a cost premium of about 15% to 20% compared to an owner mining scenario. However, due to the large number of junior mining companies entering the mining arena in South Africa contract mining rates have increased, with cost premiums as high as 50% being reported. This paper looks at the merits of owner mining versus contract mining and describes under what conditions it may be favourable to select the one option over the other. In addition, the methodology of entering into contract negotiations with the objective of establishing a fair and sustainable relationship is discussed.IntroductionOver the last decade in South Africa, there has been a significant increase in the number of mining operations, both open pit and underground, which use independent contractors to carry out mining activities. Surface mining, for example, may use contractors to conduct drilling and blasting operations or load and haul operations. Underground mining may contract out work such as shaft sinking, mining, support, construction work, cover drilling, sweeping and vampings. Common surface operations such as mineral beneficiation, waste disposal, security, and product transport may also be outsourced to contractors.Many companies have a business model that utilizes contractors for the entire mining cycle, maintaining a small head office to provide direction and control. The difficulty with this option is that often mining companies will choose the contractor option without fully understanding the implications."

Jan 1, 2015

By J. D. Bosman

The problems associated with squeezing rock conditions in tunnels are well known and have been extensively investigated in the past. Although squeezing conditions are predominantly found in tunnels developed in weak rock types it has been noted at the No. 6 Shaft of Hartebeestfontein Mine where the host rock consists of hard, brittle quartzites. This paper investigates typical time-dependent deformation mechanisms in the rock at Hartebeestfontein Mine. The paper will focus on observations made in a strike-orientated tunnel that intersected weak quartzite layers, that were sandwiched between two competent quartzite beds. The observed squeezing mechanism is dominated by creep along bedding planes with a soft talcaceous infilling that behaves in a clay-like fashion when saturated in water. Stress-induced deformation processes, some distance into the sidewall of the excavation, force the already fractured periphery of the excavation into the void. A laboratory study of the creep of intact rock and discontinuities collected at this site was conducted to characterize the time-dependent behaviour. The difference in creep rates between the two types of quartzite found at this site is described in the paper. Creep tests performed on the talcaceous infilling material found that its presence allows substantial shear creep along discontinuities. Attempts were also made to simulate the squeezing mechanism observed underground with numerical techniques. Due to the discontinuous nature of the mechanism described above, a viscoplastic displacement discontinuity technique was used as it allowed for the explicit simulation of discontinuity creep. The results of the modelling and how it compared with the observed behaviour are described in the paper. Environmental impact statement The work described in this paper will not cause any new, or contribute to any existing, hazards confronting the environment.

Jan 1, 2000

By J. R. G. Williamson

The Mining Division of Iscor, an integrated minerals and metals company, has recently completed a feasibility study for the establishment of a new heavy minerals mine and smelter in the Richards Bay area of KwaZulu-Natal, South Africa. The mine will produce a heavy mineral concentrate containing ilmenite, zircon, rutile and leucoxene which will be beneficiated at a central processing complex close to Empangeni. The ilmenite will be smelted to produce high-grade titania slag and pig iron for export. The ancient dune containing the mineral deposit is located some distance inland of the coastal dunes, and the sands contain a high proportion of extremely fine material which must be extracted ahead of the gravity separation process. Of the 56 million tonnes to be mined annually over the ten-year life of the mine approximately 23,4%?a total of 13,1 million tonnes of minus 45 micron residue fines?will have to be disposed of in a containment facility. The origin of the fine material is from the weathering of amphibole minerals. The remaining coarse sands will be returned to the mined area to re-create the original dune configuration. A number of options for the disposal of the residue fines have been examined and specialised laboratory tests undertaken to determine the deposition behaviour of the fines. The final solution involved the use of a ?sub-aerial? technique for deposition of fine material in a disposal facility. The resulting arrangement will adequately meet technical and environmental criteria. Upon closure after 10 years of operation, the surface of the disposal facility will be returned to sugar cane cultivation The paper refers to the various options considered and describes the problems associated with competent disposal of the residue fines and the development details of the final disposal facility.

Jan 1, 1997

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By S. Okubo, K. Fukui

Empirical equations established for estimating the rock strength of the working face based on the cutting forces of a tunnel boring machines (TBM) are further examined and discussed with respect to the dominant factors affecting TBM performance. Constants in the equations are related to TBM-specific parameters such as excavation (tunnel) diameter, cutter diameter, and cutter distance. The relationship between the constants and the TBM specifications is examined in this study on the basis of data collected at ten tunnels, and it is found that the constants are most strongly influenced by the cutter diameter and tunnel diameter. Zur Schätzung der Gesteinsfestigkeit an der Arbeitsfläche ermittelte empirische Gleichungen, die auf den Schneidekräften von Tunnelbohrmaschinen (TBM) beruhen, wurden weiter im Hinblick auf die vorherrschenden, die Leistung der TBM beeinflussenden Faktoren hin untersucht und diskutiert. In der Gleichung enthaltene Konstanten werden zu den TBM-spezifischen Parametern wie Auschachtungs- (Tunnel) Durchmesser, Schneidendurchmesser und Schachtlänge in Beziehung gesetzt. Die Beziehung zwischen diesen Konstanten und den technischen Daten der TBM wird in dieser Studie auf der Basis der bei 10 Tunnelbauten gesammelten Daten untersucht. Dabei wurde gefunden, dass diese Konstanten am stärksten von den Durchmessern der Schneiden und der Tunnel beeinflusst werden. Cette étude examine et discute les équations empiriques permettant d&apos;estimer la résistance de la roche attaquée aux forces de coupe des tunneliers dans le cadre de l&apos;étude des facteurs dominants affectant les performances des tunneliers. Les constantes de ces équations concernent les paramètres spécifiques des tunneliers comme le diamètre d&apos;excavation (du tunnel), le diamètre du couteau et la distance de coupe. Cette étude examine le rapport entre ces constantes et les caractéristiques techniques des tunneliers d&apos;après des données collectées dans dix tunnels et elle conclut que ces constantes sont principalement influencées par le diamètre du couteau et le diamètre du tunnel.

Jan 1, 2003

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l&apos;affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d&apos;affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d&apos;affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By D. Boldini, R. Lackner, H. A. Mang

ABSTRACT: In this paper, the strong interaction between the hardening shotcrete lining and the surrounding ground in NATM tunneling is investigated by means of axisymmetric analyses, accounting for the three-dimensional nature of the excavation process. The effect of the hydration of shotcrete on strength, stiffness, chemical shrinkage as well as microcracking and creep are accounted for. For the description of the mechanical behavior of the ground, a multi-surface plasticity model is employed. The performed analyses of the excavation process provide insight into the influence of each phenomenon accounted for in the material model for shotcrete on the response of the ground-shotcrete compound structure. ZUSAMMENFASSUNG: In diesem Beitrag soll die Interaktion zwischen dem erhärtenden Spritzbeton und dem Boden auf der Basis axisymmetrischer Berechnungen untersucht werden. Derartige Berechnungen ermöglichen die Berücksichtigung des drei-dimensionalen Charakters des Vortriebprozesses. Die Auswirkung der Hydratation auf die Entwicklung der Festigkeit, Steifigkeit und der chemischen Schwindverzerrungen, sowie das Reißen und das Kriechen des Spritzbetons wurde berücksichtigt. Das mechanische Verhalten des Bodens wurde mittels eines Mehrflächenplastizitätsmodells simuliert. Die durchgeführten Berechnungen des Vortriebprozesses geben Einblicke in die Auswirkungen der Spritzbetoneigenschaften auf das Tragverhalten des Boden-Spritzbeton-Komposits. RÉSUMÉ: La stricte interaction entre le soutènement en béton projeté durcissant et le terrain dans un tunnel creusé avec la NATM est étudiée par des analyses axisymétriques, compte tenu de la nature tridimensionnelle des processus de creusement. Les effets de l’hydratation du béton sur la résistance, la rigidité et la contraction chimique, ainsi que sur la micro-fissuration et le fluage, sont mis en compte. Pour la description du comportement mécanique du terrain on emploie un modèle de plasticité multi-surface. Les analyses conduites mettent en évidence l’influence de chaque phénomène considéré dans le modèle constitutif du béton projeté sur la réponse de la structure composite terrain-béton projeté.

Jan 1, 2003

Iron ore pellets with or without additives are commonly used as alternate charge material in both conventional and newer ironmaking processes. The performance characteristics of these pellets are normally assessed on the basis of their reducibility values, reduction strength and resistance to clustering. These properties depend mainly on the type and amount of additives and on the sintering phenomena of the pellets during firing. In the case of composite pellets (ore-coal pellets), reduction and sintering of the iron ore fines occur simultaneously. The thermodynamic and reaction mechanisms of the processes involved in the reduction of iron ore pellets with and without reductants, additives, etc., may not necessarily be identical. The reduction and sintering characteristics of pellets greatly influence the reaction mechanism and the surface morphology of the reduced pellets. The approaches in the literature to the analysis of these reduction and sintering phenomena are broadly categorized as follows: (i) empirical models, (ii) models based on kinetics, and (ill) models based on morphological changes. The relative merits and de-merits of these models are illustrated by their application to the reduction of fluxed ore-coal composite pellets. A critical analysis of the investigations that have been conducted on the reduction and sintering behaviour of such pellets is given. It is shown that, although elegant empirical models and kinetic equations have theoretical significance and can be usefully employed in elucidating the reaction mechanisms of iron ore lumps, they are sometimes not directly applicable to fluxed ore-coal composite pellets. In studies of the latter, the approach should be to correlate the morphological changes with the reduction mechanism. The paper also gives a brief account of an investigation on the reduction and sintering aspects of fluxed composite reduced iron pellets.

Jan 1, 1996

By M. Coetzee

The susceptibility of experimental low-nickel Cr-Mn-N stainless steels to hot cracking, sensitization, and pitting corrosion in the as-welded condition was investigated. These steels were developed for deep-drawing applications and are similar in composition to type 201 stainless steel. In order to obtain good formability, the rapid rate of work-hardening (characteristic of the 200-series steels) was decreased by the addition of copper. The behaviour of two sets of alloys during fusion welding was investigated: 17Cr-7Mn-4Ni-o.5Cu steels containing 0.001 to 0.27 per cent nitrogen, and 17Cr-7Mn-2Ni-o.1N steels with copper contents varying between 0.01 and 3.11 per cent. Al the steels in these two sets initially solidify as d-ferrite, which transforms partially to austenite during cooling. As the nitrogen level increases, the microstructure of an autogenous-weld metal ranges from large amounts of d -ferrite, martensite, and Widmanstätten austenite, to austenitic structures with small amounts of vermicular d -ferrite. The formation of d -ferrite during solidification and the presence of ferrite retained in the weld metal indicate that the experimental alloys will not be susceptible to hot cracking during welding. Except for the alloy with 0.27 per cent nitrogen, the resistance to pitting corrosion of the experimental steels in the as-welded condition is inferior to that of type 304 stainless steel. None of the experimental steels is susceptible to intergranular attack in the as welded condition. The alloys with 0.19 and 0.27 per cent nitrogen have properties (corrosion and microstructure) similar to those of type 304 stainless steel in the as-welded condition.

Jan 1, 1996