Search Documents

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003

By P. C. van Aswegen

The Schools A school on 'Measurement, Process Control and Optimization in the Minerals Industry', organized by The South African Institute of Mining and Metallurgy, was presented twice by course leader Dr Ken Garner, ably assisted by the staff of the Measurement and Control Division of Mintek. The first school was held from 16th to 20th July, 1984, at the University of the Witwatersrand, and the second from 11th to 15th February, 1985, at Mintek. Project development The Sydney Branch of the Australasian Institute of Mining and Metallurgy will hold a second Project Development Symposium in Sydney between 7th and 10th October, 1986. This second symposium will extend the range of topics covered by its predecessor in 1983 to emphasize planning (including strategic planning), construction, and project commissioning.

Jan 1, 1985

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By N. P. Mabasa, N. Naudé, A. M. Garbers-Craig

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling MgO-C and Al2O3-MgO-C refractory bricks, which are widely used in the steelmaking industry. Since approximately 28 Mt of refractory bricks are discarded each year, it is logical to recycle them. When furnaces and ladles are relined, the spent refractory bricks become mixed up, and need to be sorted before recycling. This study examined the use of a hand-held X-ray fluorescence analyser (HH-XRF) to distinguish between spent oxide-based and oxide-carbon-based refractory materials, with special emphasis on spent MgO-C (MC) and Al2O3-MgO-C (AMC) bricks. HH-XRF analysis was conducted on 18 oxide-carbon refractory bricks as well as on MgO-chromite and bauxite-based refractories. X-ray diffraction, reflected light optical microscopy, and scanning electron microscopy with energy dispersive spectroscopy were used to characterize the MgO-C and Al2O3-MgO-C bricks to confirm the accuracy of the HH-XRF analyses. This study also underlined the importance of calibrating the HH-XRF analyser for the refractory bricks to be sorted. The HH-XRF was successful in distinguishing between the different oxide-carbon-based refractory bricks both before and after cleaning. This result is important as it proves that HH-XRF provides a method whereby spent MC and AMC bricks can be sorted quickly and reliably.

Jan 26, 2023

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

By L. Ziyuan, S. Chunbao, K. Jue, H. Yang, S. Tichang

In this study, potassium ferrocyanide, a non-toxic cyanide precursor in dark and diffuse reflection environments, was applied as a reagent for the leaching of gold. The free cyanide ions were gradually released from the potassium ferrocyanide solution under the ultraviolet light. Orthogonal leaching experiments were performed in gold ore to analyse the effect of solution pH, potassium ferrocyanide dosage, and temperature in potassium ferrocyanide solution system under UV light. Response surface methodology (RSM) was applied to explore the role of potassium ferrocyanide in gold leaching, Optimised results showed that the gold recovery reached 67.74% in a high-alkaline environment at a 12.6 pH, 3.8 kg/t potassium ferrocyanide dosage, 62°C, and irradiance of 10mW/cm-2. The gold leaching kinetics was monitored by quartz crystal microbalance with dissipation (QCM-D) of potassium ferrocyanide solution. The results indicate that the gold extraction process consists of two processes: adsorption and leaching, and a rigid adsorption layer formed on the reaction surface. Furthermore, Xray photoelectron spectroscopy (XPS) analysis of the gold sensor surface after leaching reaction showed that -C≡N appears on the gold sensor surface, and the gold is oxidised to form AuCN complexes. Keywords: Gold leaching, potassium ferrocyanide, UV light, QCM-D, AuCN complexes

Jan 1, 2020

By C. A. Snyders

This paper investigates the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were performed on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of platinum, palladium, and gold were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours and 100 per cent, 97.4 per cent, and 99.9 per cent respectively after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while nickel concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, nickel adsorbs at approximately the same rate as that of the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and experiments suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing.

Jan 1, 2012

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located above the Arctic Circle in northern Sweden, is the second-largest underground mine in the world today. The orebody is a world-class high-grade magnetite deposit, from which three raw ore products are extracted. We use mixed integer programming to determine a production schedule, i.e., which production blocks to mine, and when to start mining them, so as to minimize deviation from planned production quantities while adhering to the operational constraints of the mine. The resulting model contains thousands of binary variables and a commensurate number of constraints, precluding us from obtaining a schedule in a reasonable amount of time. We describe a method that builds on prior, related work, to expedite solution time. Keywords: underground mining, production planning, optimization, integer programming

Jan 1, 2003

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

By H. P. Kritzinger, T. C. Kingsle

"Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications, including ferrovanadium, nickel carbonate, nickel laterite, iron ore reduction, and spodumene (lithium) production.This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates."

Jan 1, 2015

By E. L. Atkinson, G. W. Leach

The paper discusses the reasons for the introduction of load-haul-dump (LHD) units into Greenside Colliery, and the circumstances leading to the replacement of conventional mechanized equipment on a trial basis in the mining operations on No. 2, 4, and 5 seams. An outline is given of the factors governing the selection and introduction of these units into coal mining, and the associated mining and engineering aspects involved in the optimization of their use. Operating statistics comparing the performance of conventional and LHD equipment are included.

Jan 1, 1979

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely: codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage like nuclear power generation where international cooperation is eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit their mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2003

By J. E. Dickinson, R. Campbell, M. J. Cole, K. P. Galvin, M. C. Cole

It is common practice in the beneficiation of iron ore ultrafines to apply reverse flotation, and hence float the gangue minerals, leaving behind a high-grade iron ore product. Given the difficulty in floating particles finer than 20 μm, especially those finer than 10 μm, it is necessary to subject the feed to desliming ahead of flotation. There are two problems with this approach. Firstly, given the known inefficiencies of cyclones, desliming needs to be aggressively applied to particle sizes upwards of 45 μm to ensure all the offending ultrafine gangue is removed. Secondly, desliming also removes a significant portion of the valuable iron ore. Thus, a significant portion of the ultrafines, including the iron ore, is lost to the tailings. This paper examines the direct flotation of iron ore fines using the Reflux Flotation Cell. The RFC operates using a concentrated bubbly zone, in the absence of a conventional froth zone, for delivering strong counter current washing through an inverted fluidised bed of bubbles ahead of the product discharge. A system of parallel inclined channels in the lower part of the cell provides enhanced segregation of the bubbles from the tailings, preventing the loss of air bubbles into the tailings. Experiments conducted under semi-batch conditions produced encouraging results with concentrates of ~65% Fe grade in a single flotation stage. Comparatively, up to five successive batch flotation stages were required when using a laboratory scale batch mechanical flotation cell to achieve similar Fe grades. For a given grade, lower Fe recoveries were typically achieved by the RFC. This was attributed to the effective prevention of ultrafine particles succumbing to hydraulic entrainment under a positive bias flux, as well as an increasing feed volume involved in the semi-batch operation using inverted fluidisation water for cleaning. Overall, similar grade-recovery curves were produced, however, significantly higher grades were obtained by the RFC and with fewer separation stages. Keywords: Desliming flotation, iron ore, modified release analysis, reflux flotation cell

Jan 1, 2020

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions.

Jan 1, 2012