Search Documents

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

By I. V. Samarasekera, E. B. Hawbolt

A review of recent work being conducted at the university of British Columbia on the modeling of the microstructural evolution during the hot rolling of steel is presented. A mathematical model of heat transfer was developed to describe the thermal field in a slab during rough and finish rolling. The model for rough rolling, discussed in this review, also simulates the growth of oxide scale on the slab surface. To quantify the heat transferred from the slab to the work rolls, instrumented samples of MSI3O4 L stainless steel, 0,05 per cent carbon steel, and 0,05 per cent carbon steel with 0,025 per cent

Jan 1, 1995

By J. H. deur Potgieter

This paper, 'A review of the biological treatment of cyanide-bearing waste water' discusses the necessity for the treatment of cyanide-bearing waste water with a view to the avoidance of environmental pollution, and the limitations of the available chemical and physical processes are referred to briefly. The sources of cyanide-bearing waste waters are mentioned. The mechanisms of production and utilization of cyanide by fungi and bacteria are discussed. The work done in connection with the biological removal and destruction of cyanide is summarized, the successes achieved are described, and the relevant processes are listed. In conclusion, some advantages of biological processes for the removal of cyanide are mentioned.

Jan 1, 1991

By M. Guarascio

Microseismic monitoring of mining areas is a developing technique, described here for the Belvedere Spinello Mine, southern Italy, where dissolution cavities in the mining area have proved problematic. The preliminary condition for locating seismic impulses has been found to be a reliable seismic ground model. Ground signals are continuously recorded by means of data from piezometric wells, for sinkhole data, and linked gephones, for microseismic data. A computer system has been implemented to collect, analyse and interpret the incoming signals consequently, identification and classification of hypocentres of activity is facilitated, with advantages in terms of safety, preventing harmful side-effects, including rock bursts, and for environmental conservation.

Jan 1, 1987

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By G. E. Rencken, J. H. Potgieter, A. Narain, J. Smith

To conserve fresh water resources and comply with environmental regulations, DRDGOLD, a South African gold producer re-treating surface tailings, has transitioned to a fully closed water circulation system. Consequently, the accumulation of contaminants, as well as addition of reagents, has led to changes in water composition that have compromised leach performance and overall gold recovery. A two-sample t-test confirmed a significant difference in gold recoveries between the use of Rand Water, which was used as a benchmark, and untreated process water. Atomic absorption analysis of ERGO’s process water, confirmed the presence of iron, nickel, zinc, and manganese. A study of the effect of the identified contaminants on gold recovery showed that iron, nickel, and zinc have the largest negative effect on gold recovery, with iron and nickel being more detrimental than zinc. Sulphates were shown to have a possible passivation effect, which also influenced gold recoveries, although to a lesser extent than the heavy metals. Calcium, when present in excess, had a positive influence on gold recovery indicating the possible formation of a calcium aurocyanide complex. Lime softening successfully reduced the heavy metal and sulphate concentrations, and the gold recoveries obtained with the treated process water were similar to those as achieved with Rand Water.

Jul 1, 2021

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By M. Salimov, J. Sattarvand

The conventional visualisation method of remote equipment is through the installation of one or more cameras on the machine, and sending a live feed to the operator’s flat display. However, the performance of the teleoperation can be enhanced using better visualisation through virtual reality (VR). This paper presents the process of the design and manufacturing of a robotic platform that will be used in the next phase of the project for a VR-assisted teleoperated excavator. The robot consists of a loading boom and arm arrangement installed on the undercarriage of a CAT300-9D. All hydraulic cylinders are replaced with electric actuators, and crawling motors are substituted by electric motors. The pieces of the boom and the arm, as well as the bucket were designed in Autodesk Inventor, and manufactured from aluminium sheets using a desktop and CNC machine. Parts are joined by pins and welding as needed. An Arduino-based control system is developed for the robot, and motor controllers are used to convert the power commands from the microcontroller to the high-amperage actuators. The control system is capable of communicating with a wireless Play Station controller to operate remotely. The manufactured robotic excavator is planned to be utilised in multiple autonomy research projects.

Sep 1, 2021

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

Mine wide, underground wireless communications are possible with the use of Ultra Low Frequency (ULF) technology. Due to the propagation through rock of ULF radio signals a relatively small antenna can provide communications coverage over a complete mining operation. Starting as a Personal Emergency Device (PED) for emergency messaging to miners under all circumstances, the ULF communications system has grown to include capabilities of remote control of underground equipment such as pumps and fans and centralised blasting initiation. This technology is now in use on 5 continents having lately made it onto the African mining scene. The paper and presentation will provide the audience with the benefit from international mining know-how in this technology as well as local African experiences. A recent commissioning exercise for example, is expected to pay for itself in electricity savings within a few months. These and other results from practical demonstrations and usage will be covered. This novel technology becomes an integral part of the daily operating infrastructure of a mine with immediate safety and business benefits. It is able to reduce capital expenditure and is designed for ease of routine operational use. The paper will conclude with insights into current R&D for further development of this technology.

Jan 1, 2007

By D. E. Ng?andu

The experience of Mufulira concentrator, of the Zambia Consolidated Copper Mines Limited, with underground mine drainage water, which is used in milling operations is discussed. It is shown that the underground mine water has a deleterious effect on flotation performance. The adverse effect of the underground water was successfully negated by adding lime into the primary ball mills and increasing the pH of the slurry, from a ?natural? pH of 8 to the flotation pH of 10.5. Traditionally, the pH modifier, quicklime, had been added downstream of the milling. Changing the lime addition point further reduced lime consumption by 50%,?a key issue as lime accounted for over 60% of the Mufulira flotation reagent costs. The nature of the effect of the underground water at Mufulira, particularly the sensitivity of the flotation to the pH at which the milling was conducted, characterized galvanic interaction. A large-scale plant situation is presented in which the desired electro-chemical response in the flotation was achieved, by a deliberate manipulation of the milling environment. The experience provides practical testimony of a more fundamental role for the milling process, other than the mere physical preparation, i.e. size reduction and liberation, of mineral particles prior to flotation.

Jan 1, 2001

By M. G. Senyur

This study aims at investigating the structural characteristics of backfilling material. In this regard, spatial arrangement of solid particles and associated voids in a unit mass of coal mine refuse as backfilling material were tested. The materials were produced from coal mine refuse of Zonguldak Colliery, Turkey. The experimental procedures were developed to determine their void ratio (or its equivalent porosity), bulk density and the shape properties of constituent particles. The orientation fabric and the co-ordination number were the other two fabric elements determined. The filling materials were sieved and their particle size distributions were found. The results obtained by experiments were related to the particle size distribution parameters, namely, the coefficient of uniformity and the effective size. It was concluded that mean value of void ratio is correlated with coefficient of uniformity. The standard deviation of porosity as an index of fabric heterogeneity is clearly correlated to effective size. By an original experiment, the frequency distribution of coordination number was observed as binomial in uniformly graded materials. Also, the co-ordination numbers of test mixtures were calculated by the Marsal method and results obtained showed a good correlation between the minimum particle size and number of contacts per unit area.

Jan 1, 1998

By A. K. Verma

Several longwall faces in India have collapsed due to adverse geological conditions and/or inadequate capacity of powered supports. Thus it is imperative to access the capacity of a powered support and its interaction at longwall faces of varying geomining conditions in advance with lots of confidence. To achieve this, an index has been developed to ascertain the front leg pressure (FLP) of chock-shield support and roof-to-floor convergence (RFC) at longwall faces. The index called ?Longwall Face Stability Index? (LFSI) has been developed using statistics and Finite Element Modelling (FEM). The front leg pressure (FLP) and roof-to-floor convergence (RFC) predicted from the LFSI are validated with the field monitored data from two longwall panels. In this study, an attempt is also made to incorporate various geomining conditions into the finite element models typical of longwall mining practice. The index has taken into account the wide variations of geomining parameters like thickness, young?s modulus and friction angle of main roof (small, large), coal type (soft, hard), powered support capacity, and depth of coal seam. Thus, LFSI can be thought of as an index representing combined effect of roof type, geomining conditions and powered support capacity.

Jan 1, 2008

By L. Munsamy, B. J. Madden

OpenRisk, an open cast risk rating system, takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and operational parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all the strip mines would use an identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. This system has been made practical and easy to use. Therefore, this tool can be used by personnel from other disciplines not directly related to rock engineering. OpenRisk system has been in operation at nine Anglo Coal and other open cast mines. It adequately detects areas of high risk and generates adequate remedial solutions to reduce the risks. Awareness of the personnel has been higher at the sites that use OpenRisk. The proactive approach of OpenRisk ensures that all personnel are aware of risks in the pits and how to deal with potential risky areas.

Jan 1, 2006

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By R. L. Attridge

Namibia's newest mining enterprise, the Navachab Gold Mine, was officially opened by President Sam Nujomo during June 1990. The mine is a joint venture between Erongo Mining & Exploration Company Limited, Metal Mining Corporation of Canada, and Rand Mines Windhoek (Pty) Ltd. Erongo has a 70 per cent interest in the mine, while Metal Mining and Rand Mines hold 20 per cent and 10 per cent respectively. Anglo American Corporation and its associates hold two-thirds of Erongo shares and CDM (Pty) Ltd one-third. The Mine is managed by Erongo Mining & Exploration Company. The property is located some 10 km southwest of the town of Karibib and 170 km west-northwest of the Namibian capital of Windhoek (Fig. 1), the name of the Mine being taken from the farm on which the gold deposits were discovered. Navachab is an opencast operation and was brought into production in December 1989 at a cost of around R84 milion-RS,2 million under budget. The plant is designed to treat 840 kt annually at an average gold grade of 2,6 g/t. This wil produce 1900 kg of gold per year, which at today's prices will earn Namibia more than R60 million in foreign exchange.

Jan 1, 1991

By R. Tinsley

Project-finance risk assessment is mature and approached systematically. Mining industry due diligence remains fragmented with specialists addressing different aspects of the project such as reserves/JORC, environmental impact, commodity market, even financial analysis/ modelling. Each professional has a natural tendency to believe that the risk factors they have examined are the key ones necessary to be reviewed, as if their review will stand in isolation from others in the way a project materialises. By first laying out the project risk categories and risk matrices, this paper examines the due diligence process with a keen eye to the risk assessment and overlap/interaction. Some cross fertilisation of due diligence techniques from other industry sectors is placed into the mining context. Six case studies are then presented with regards to due diligence features in each project's feasibility review or financial information/ offering memorandum. A power case first shows the differences between the due diligence expectations of banks versus bond financings. Then some Australian and Indonesian mining development cases are analysed to see the due diligence learning points. Some of these were project/due diligence failures. The conclusion focuses on the value of a systematic risk assessment for project evaluation, all from the project-finance perspective.

Jan 1, 2007

By V. N. Medvedev, A. M. Bryukhanov

Stationary mine air control equipment enables monitoring of CH4 concentration only in sensor locations. CMC-4 individual indicator built into a caplight has been developed in Ukraine, extending CH4 monitoring to manned job sites. Major technical characteristics of the indicator are demonstrated. It features two operation thresholds: 1st threshold 1.0 to 2.0% vol. 2nd threshold 1.5 to 2.5% vol. Basic absolute accuracy ± 0.2% Caplight battery is a common power supply for the lamp and CH4 indicator, providing at least 10 hours of the system non-stop operation. Average pre-failure life is at least 10,000 hrs. It features: an explosion proof design and intrinsically safe test circuit; a small-sized sensor as an integral part of the caplight; a hybrid microcircuit to facilitate functioning of methane monitoring unit. The CMC-4 indicator weight is the weight of the caplight itself and equals 2.4 kg. A two-threshold design makes possible to distinguish between methane sources: slow accumulation due to diffusion or sudden rushes due to a gas-dynamic event. CMC-4 indicators in addition to stationary equipment minimize the risk of CH4 explosion underground determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By A. Nhasengo

Paper written on project work carried out in partial fulfilment of B. sc. Eng (Mining Engineering) The purpose of this investigation was to assess the mining strategy for steep reefs at Mine A mine in 2005 and 2006. Reefs steeper than 35° were discovered when production commenced at the mine. At that time reefs steeper than 35° were not popular in South African tabular gold mines, therefore new techniques of mining them had to be developed. The underhand mining method was chosen for this purpose. The project was about assessing ventilation, support costs, local support cycles, adherence to the mine?s support standards, mine planning and efficiencies of the underhand mining method. The project work was covered by doing a literature research for underhand mining methods and performing a literature review of the mining methods, support methods, ventilation standards at Mine A. Underground visits were conducted at Mine A mine for data collection, and Mine B was visited to obtain information on support costs and efficiencies. During the investigation it was realized that the underhand mining method was an appropriate method for mining steep reefs; however, there were some challenges related to ventilation and support installation. Efficiencies could be realized with the underhand mining method and planning and scheduling were not different from breast mining.

Jan 1, 2007