Search Documents

By V. Yahorava

Efficient recovery of precious metals from process solutions is essential for improving process economics. Traditionally, precious metals are relatively effectively recovered from waste streams via precipitation or cementation. However, these approaches have a number of drawbacks, including poor water balance, creation of environmentally unfriendly waste streams, and losses of precious metals. Ion exchange technology is an alternative for the recovery of precious metals from waste or low-grade streams. This technology allows the recovery of the precious metals to extremely low levels (micrograms per litre) with relatively high upgrade ratios from the solution onto the resin without major water balance concerns, while the impact on the environment could be minimized or avoided. Research was conducted on the recovery of platinum group metals and gold from different low-grade and waste streams from one of the precious metals refineries in South Africa by means of ion exchange. Various functionalities and matrices (granular and fibrous) of ion exchange materials were evaluated. The results from these studies indicated that in some cases ion exchange could be very effective for the recovery of precious metals, and that the PGM concentration could be reduced to < 1 mg/L. The upgrading ratios of the various PGMs onto the specific fibres were relatively high for the specific streams evaluated, which might in some cases justify incineration of the loaded material instead of stripping and recycling the adsorbent. The cost of direct incineration for one of the waste streams tested would be less than 1% of the value of the PGMs recovered. However, the adsorbent has to be carefully selected and the process design optimized for each specific stream.

Jan 1, 2014

By A. A. Rogozhin, S. I. Anufrieva, A. V. Kurkov

The results of development of technologies for flotation concentration of two types of complex beryllium ores are presented: beryllium-fluorite in apocarbonate metasomatites (Type I) and rare-earthberyllium in feldspar metasomatites (Type II). The researched samples of Type I ores contain a mineral complex that is difficult to separate by fatty acid flotation, including phenakite, bertrandite, fluorite, and carbonate minerals. The ores are characterised by an increased content of fluorite and carbonates. The sample of Type II ore contains such rare-earth minerals as bastnesite and orthite, and a beryllium mineral - cleiophane. The size of individualised grains of cleiophane does not exceed 0.04 mm, which significantly limits the possibility of extracting the mineral into the enrichment concentrates. For the Type I ores, a technological process for the extraction of fluorite using a phosphorus-containing reagent from the class of dialkylphenyl polyethylene glycol esters of phosphoric acid (DAPEGEPhA) has been developed. The use of DAPEGEPhA enables the production of a high-grade fluorite concentrate (95% CaF2). The production of commodity phenakite-bertrandite high-grade (10% BeO) flotation concentrate from the fluorite flotation tailings with using a fatty acid collector is based on binding calcium in the flotation pulp using soda, sodium hydroxide and sodium tripolyphosphate. The use of a combined collector based on fatty acids and DAPEGEPhA made it possible to produce a collective rare-earthberyllium- lithium concentrate with high REE extraction (88%) from the Type II ores. The concentrates obtained are suitable for production of commercial-grade hydrometallurgy products. Keywords: Beryllium ores, flotation, reagents, concentrates, hydrometallurgy products

Jan 1, 2020

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d&apos;excavabilité sont souvent en grande partie ignorés. Tandis que le choix d&apos;une méthode de percement économique est évidemment une priorité claire dans l&apos;étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By S. Carter

this paper describes an innovation in computer software that permits mining professionals to collaborate on exploration and mining projects regardless of geographic location. Growth of mining companies through merger and acquisition has created a greater need for mining professionals to collaborate, especially as projects and project participants are becoming geographically remote. Surpac NetVision, the name given to this new collaboration technology, satisfies this need by deploying interactive 3D graphics sessions across computer networks. It achieves this by using common web browser technology as the deployment medium. A plug-in architecture that supports diverse file formats permits transparent read and write of foreign data to further enhance the collaboration process. Surpac NetVision supports any number of connections from web browsers on remote computers using existing networks. Software components required to enable the collaboration session are deployed to the remote computer as required and cached for future sessions. The collaboration session at each computer is characterized by a fully functional replica of the user interface for Surpac NetVision from which any function can be executed by any client, at the owners discretion. All geometry and display attributes deployed to remote clients to render 3Dgraphics are highly compressed to reduce bandwidth requirements. The key benefits of this collaboration technology is improved communication in regard to exploration and mining projects leading to: •More informed decision making •Improved deployment of project objectives and plans beyond the technical planning group to project management and operations staff •Improved technical support for software users. Keywords: 3D graphics, project collaboration, interactive graphics, internet 3D graphics, mining software

Jan 1, 2003

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

For practical reasons all basic input data for the gold mines of the Anglovaal Group conform to a regular grid of averages of sample values within 25-ft squares in the plane of the ore body; individual sample values with their metric co-ordinates are input and converted by a computer program to the basic 25-ft square averages. At the Prieska copper mine the bore- hole data are forced on to a regular grid of 15-m squares corresponding to the coordinates of the grid points nearest to the actual borehole intersections. As for the gold mines the Prieska ore body, although some 3 to 30 m thick, is also dealt with on a two-dimensional basis (Krige, 1973). On the gold mines the data subjected to geostatistical analysis cover: gold values (in cm g/t), uranium values (cm kg/t), and channel widths (cm). The gold and uranium values are normalised on the basis of log (value plus constant) and all the geostatistical analyses are performed on these transformed values. The channel widths usually conform reasonably well to the normal distribution and are, therefore, not transformed. At Prieska the metal grades analysed cover the two main products, copper and zinc, as well as the impurities lead and bismuth; in addition the specific gravity values and the hanging- and foot-wall deviations from a projection plane are also handled. These were all previously used on an untransformed basis but because of problems associated with the proportional effect the lognormal-de Wijsian model is now used for some of the grade variables. The key computer pro- grams can be summarised briefly as follows:

Jan 1, 1981

By B. B. Tati

The project report is based on vacation work done by the writer at the Khutala Colliery during December/January 2009?2010. The purpose of this report is to explain and describe the design process in a multi-seam mine design for coal extraction at the Khutala Colliery. The multi-seam design will focus on the No. 2 and No. 4 seams as these are the seams that are currently being mined by underground methods at Khutala Colliery. The seam thicknesses and the parting thickness between the seams provide suitable conditions for designing a multi-seam mine design. An investigation into the pillar design aspects is carried out followed by a numerical modelling analysis of various scenarios. This analysis validates the first principles approach provided by multi-seam design guidelines. The design results from the analysis of the selected pillar design indicate sufficient parting for primitive conditions between seams, thus illuminating the need for superimposing in-panel pillars. This multi-seam mine design confirms the potential for the extraction of coal in a new panel. The design indicates that significant amounts of power station coal are present and suitable for extraction by room and pillar mining methods. The panel block indicates 401 625 tonnes of ROM coal. This block has a life of panel that will be mined just over a 4-month period. This 4-month period is assumed to mined at a production rate of 48 000 tonnes per month. The total capital cost required for the new panel is R48 281 127.05. Keywords Multi-seam mining, panel design, ventilation flow, superimposition.

Jan 1, 2011

By A. Chiappone, M. Barla, U. Rabagliati, L. Repetto

ABSTRACT: The paper describes the application of both continuum and discontinuum modelling to the study of the stability conditions of the Alpetto mine, a high rock cut located in Cesana Brianza (Italy). The main objective is to provide valuable information for future mine planning and for the assessment of the stability conditions of the abandoned high rock cuts. Continuum modelling involved the applications of the finite difference method, whereas the distinct element method was used for discontinuum modelling. RESUME: L&apos;article décrit l&apos;application des méthodes de modélisation continue/discontinue pour l&apos;étude des conditions de stabilité de la mine d&apos; Alpetto, située à Cesana Brianza (Italie). Le but du travail consiste à determiner des paramètres utiles vis-à-vis du projet et d&apos;estimer les conditions de stabilité de l&apos;amas rocheux au terme de l&apos;exploitation de la mine susmentionnée. La modélisation continue a impliqué l&apos;application de la méthode des différences finis alors que la méthode des éléments distincts a été utilisée pour la modélisation discontinue. KURZFASSUNG: Der Artikel beschreibt die Verwendung der Modellierung von continuum und discontinuum zur Untersuchung/Studium der Stabilitätsbedingungen von der Alpetto Mine, hohe Aushubsfront in einer Felsmasse die sich in der Gemeinde von Cesana Brianza befindet. Das Hauptziel dieser Arbeit ist die Festlegung von Parametern die zur Planung nützlich/behilflich sein können sowie auch die Möglichkeit zur Analyse/Auswertung der Stabilität der Felsmasse-Front nach Aufhebung der Nutzung derselben. Die continuum Methode/Analyse wurde verwendet durch Unterstützung der Finite Differenz Methode da man für die Analyse der discontinuum (Fels als discontinuum beschrieben) der Distinct Elemente Methode verwendet hat.

Jan 1, 2003

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By B. C. Alberts

The South African Institute of Mining and Metallurgy arranged a well-attended Colloquium on Management Techniques in the Mining and Metallurgical Industries at the C SIR Conference Centre from 13th to 15th June, 1988.

Jan 1, 1988

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By F. Nakhaei, Z. Pourkarimi

Tailings produced from the iron ore industry present many challenges due to the high economic and environmental impacts involved with their disposal. However, the relative scarcity of high-grade iron ores has driven manufacturers to recover and recycle these valuable tailings (secondary sources). This study aimed at the purification of ultrafine tailings with high sulphur content from an iron ore concentrator via reverse flotation to produce pellet feed fines. A specially designed flotation column featured with a nano bubble generator and a conventional bubble generator were employed to assess the effects of nano bubbles on the desulfurisation performance of iron ore concentrate under different operating conditions. Results obtained from this study indicated that the sulphur content of iron concentrate could be reduced from 1.2% to 0.22% in the presence of nano bubbles. Also, the results showed that use of nano-micro bubbles increased sulphur recovery 20% more, in comparison to micro bubbles. Keywords: Column flotation, iron ore, tailings, slime, nano bubbles, desulphurisation

Jan 1, 2020

By M. Lange

The postulation that primary platinum group metal (PGM) matte will chemically react with magnesia-chrome bricks when temperatures exceed 1500°C was tested. Magnesia-chrome brick samples were heated in contact with matte at 1300°C to 1750°C for 30 minutes, after which the refractory samples were analysed using reflected light microscopy and scanning electron microscopy. The samples were all completely penetrated by matte. As the temperature increased the matte also penetrated the fused aggregate grains and disintegrated them. The chromium concentration of the matte inside the refractory samples was found to be slightly higher than that of the bulk matte. At temperatures of 1500°C and higher, MgO, FeO, and magnesium-rich silicate crystals could be identified in the matte directly adjacent to the refractorymatte interface. Phase relations clearly indicated that chemical reactions take place between primary PGM matte and the magnesiachrome refractory material at temperatures above 1500°C, but that these reactions are more complex than expected from FactSAGE® calculations.

Jan 1, 2014

By S. Ling, T. Liu, Y. Shang

A new copper-molybdenum flotation technology developed for a certain coppermolybdenum ore is introduced. We achieved copper-molybdenum bulk flotation in lowalkali conditions. Locked-circuit test results showed that the bulk concentrate contained 21.05% Cu and 1.10% Mo, with copper recovery of 87.37% and molybdenum recovery of 77.07%. For the copper–molybdenum separation process of the bulk concentrate, we use a new depressant, BK511, to replace the traditional sodium hydrosulfide. We achieved copper–molybdenum separation through one rougher, nine cleaner, and two scavenger processes. The results of locked-circuit tests showed that the molybdenum concentrate contained 46.19% Mo and 0.75% Cu, with molybdenum recovery of 93.80%; the copper concentrate contained 21.50% Cu and 0.069% Mo, with copper recovery of 99.92%. This new technology overcomes disadvantages of using large amounts of lime, sodium hydrosulfide, and other reagents in traditional copper–molybdenum flotation.

Jan 1, 2023

By Richard F. Link, Jr. Koch

"A mathematical simulation model has been devised to guide the layout of surface or underground mine workings, drill stations, and drill holes that are established in order to search for tabular ore bodies. The ore bodies may be contained within veins, sedimentary beds (including reefs), or other tabular structures.Programmed for a time-shared digital computer, the model contains both stochastic and deterministic variables. Stochastic or natural variables include the number of ore shoots and their sizes, orientations, locations and values. Deterministic or controllable variables include (i) locations and costs of workings (for underground exploration); (ii) drill station locations and costs; and (iii) drill hole azimuths, inclinations, lengths and deflections (if any).For various assumptions about the natural variables, the model is run while the controllable variables arc changed deliberately. Thus, layouts are devised to determine the percentages of the total number of assumed ore shoots found at different costs. In order to choose among the various layouts, cost-effectiveness measures are calculated."

Jan 1, 2014

I appreciate the honour that has been bestowed upon me by my election as President of this Institute. We are starting what I believe will be a challenging year. The first challenge facing the Institute is financial. From the accounts for you will note that the Institute operated at a loss for the first time since 1987. average membership subscription was increased by only 10 per cent, reflecting desire to keep costs down in the minerals industry. The Institute will therefore to rely on other income to meet its budget requirements and break even financially. source of these funds will be the activities of the Technical Programme Committees. disciplines-Mining, Extraction Metallurgy, and Metals Technology are planning programmes for the coming year. I urge al members to increase their support of colloquia schools. Increased membership would also bring in more funds. Please, therefore, encourage colleagues who are not yet members of the Institute to join it.

Jan 1, 1991

By E. Robles

The Tati Activox® Project (TA®P) is the first step towards the implementation of the Norilsk Nickel Activox® process. The ultrafine grinding (UFG) and autoclave pressure leach process conditions are the heart of the Activox® patent. Low grade base metal sulphide concentrates are leached in the process to recover the base metals and to produce LME grade nickel and copper cathodes and cobalt carbonates. The downstream processing of the metal-containing liquor produced by this process includes solvent extraction circuits to extract and concentrate metal-rich solutions, before the various final products are obtained. This paper gives an overview of many of the relevant design aspects taken into consideration in the design of the Tati Activox® solvent extraction circuits. It addresses key design elements related to leach process conditions such as scaling, materials selection for corrosive solutions, pH control, crud formation and treatment, multiple SX trains designed to prevent organic cross-contamination, and design aspects related to the mitigation of fire risks.

Jan 1, 2009

By G. Taylor

A 21st Century worker is one who works less with his physical power and more with mental ability. Such a worker is more skilled than a labourer and is consequently rewarded accordingly. A21st Century supervisor is one who ensures that workers are constantly supported so that they can maximize safety and productivity. A 21st Century manager is one who constantly searches for ways to maximize returns for the various stakeholders. Given the well-known constraints in narrow reef mining, all of the above is meaningless unless a mining method is found which provides conditions which support the 21st Century initiatives. [ ] The identified mining method is a continuous non-explosive stope breaking system using rocksplitter technology. Rocksplitting is defined as: The fragmentation of rock through high energy pulse wave transmission in a fluid-filled hole or hydro fracturing. Shotholes are effectively filled with a water-based geland 30 grams of explosive after which the hole is closed off with a ?rocksplitting gun?.

Jan 1, 2000