Search Documents

Contribution by W. Assibey-Bonsu I congratulate Mr N.O. Lotter on his paper. There are two main aspects of the paper on which I would like to comment. One aspect is his review of P. Gy's sampling theory under the heading 'Sampling the mill feed' (p. 153). The other aspect relates to his reference to one of our papers1 that was published in the Journal (p. 152). My comments on the former will be given elsewhere'. Authors' reply: Dr Assibey-Bonsu's contribution to the subject is appreciated.

Jan 1, 1996

By David J. Haddock

On Wednesday, 6th July, 1988, 28 members of the Johannesburg Branch of The South African Institute of Mining and Metallurgy and their guests assembled at the Rand Refinery Sports Club, which is situated within the Refinery complex, to hear Dr Daniel Polnow, General Manager of the Refinery, give a very interesting lecture on the Rand Refinery Complex and its activities. Accounting for gold The South African Institute of Mining and Metallurgy will be holding a 3- or 4-day school in the third week of May 1989 on the topic 'Accounting for Gold'.

Jan 1, 1988

By A. Montini, M. H. Moys

A technique for the measurement of slurry consistency inside a grinding mil is described. The rate of slurry drainage from a sensing probe mounted through the mil shell is measured and correlated with the percentage solids of the slurry discharging from the mil. The response time of the measurement(obtained on a pilot bal mil) is compared with the response time of the viscosity of the mill discharge. It is shown that the new measurement should allow much tighter control of the mil behaviour, with concomitant savings in the consumption of power and steel.

Jan 1, 1988

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995

By P. C. Schutte, N. B. Strydom, A. J. Kielblock

Three groups of unacclimatized men were subjected to five-day climatic-room procedures at wet-bulb temperatures of 29,30, and 31 C respectively. The findings indicated that individuals reach a satisfactory level of heat acclimatization for work in environmental temperature conforming to those at which they were acclimatized. It is, therefore, superfluous to acclimatize men at wet-bulb temperatures that exceed those at which they are destined to work. These methods of acclimatization can be linked advantageously to heat-tolerance testing at mines with suitable underground temperatures.

Jan 1, 1983

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By M. J. Nicol, G. Cromberge

An account is given of the development of a relatively simple model that describes the kinetics of the absorption of gold cyanide on activated carbon. The model is based on the treatment of the carbon solution interface as a homogeneous boundary across which gold is transported at a rate determined by the rate of mass transport to and from the interface. Rate equations derived from this model describe the results of various kinetic experiments under continuous or batch conditions in the laboratory and on operating pilot and full-scale plants.

Jan 1, 1983

By R. Watts, R. A. Laybourne

This paper describes how a 'mined out' coalfield is being mined successfully by opencast methods. The coalfield is that at New Vaal Colliery, which is situated in the Vereeniging-Vanderbijlpark-Sasolburg industrial complex. Al three coal seams at New Vaal had been mined previously, when the better-quality coal had been removed. The coal-preparation plant at New Vaal, which is also described, supplies coal to the 3600 MW Lethabo Power Station. The Colliery has been designed to supply 600 million sales tons of coal over its forty-year life.

Jan 1, 1990

By M. Sciarone, B. Collins

The production, properties, and selection of ferrosilicon powders for heavy-medium separation by B. COLLlNS. B.Sc Eng. (Rand) (Fellow). T. J. NAPIER-MUNN. B.Sc. (Eng.). A.R.S.M. (Visitor). And M. SCIARONE. M.Se. Eng. (Delft) (Visitor). There are basically two types of ferrosilicon powder available to operators of heavy-medium plants in South Africa spherical and milled grades. The production processes are described, and the properties of the two types are examined and compared. Guidelines are given for the selection of the correct grade of ferrosilicon for any particular application.

Jan 12, 1974

By X. M. Prevost

A computer system to store, retrieve and process coal borehole and analytical data together with other geological, geographical or topographical information is described. As a result of the large volume and variety of data stored since its inception in 1979, as well as the basic versatility of the system, the National Coal Data Base has been performing a number of new tasks for which it was not originally designed. As considerable sets of data are used on almost every project, the use of statistical application programs has become an important processing tool.

Jan 1, 1987

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By M. Bryson, G. Marap, M. Ntlhane, M. D. Hlahane

This study investigated flotation of phosphate from a low-medium grade 8-12% P2O5, 65-73% SiO2 sedimentary phosphate ore from Kropz Elandsfontein (herein referred to as Elandsfontein) in South Africa. Quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) was used to determine apatite grain size distribution, liberation and mineral association in the F2 horizon sample. The mineralogy indicated that apatite was liberated and for the Elandsfontein plant to operate at the design throughput, the flotation feed has to be milled to a coarse grind ranging between 300 μm and 425 μm. Reverse flotation process routes using varying reagent dosages, and flotation feed top sizes that could possibly yield a final product of 31% P2O5,10% SiO2 at a reasonable +70% P2O5 recovery were investigated. Based on the results, a split circuit of coarse (-300+212μm) flotation and fine (-212+20μm) flotation, was mostly preferred as compared to treating the whole ore. A final combined concentrate of 31% P2O5 and 10% SiO2 with P2O5 recovery of 84% could be produced from the reverse split circuit. The robustness of reverse flotation for both coarse and fine fractions was further investigated. Reverse flotation of the fines fraction was found to be robust and produced a final product of 31% P2O5. It was however more challenging to achieve the required product grade and recoveries on the coarser fraction (-425+212μm), suggesting that reverse circuit was not adequately robust at fractions coarser than 300μm. Keywords: Phosphate, sedimentary, reverse flotation, particle size

Jan 1, 2020

By S. Burks

This paper develops the themes explored by the authors at the Fourth International Platinum Conference,. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: > An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated > An existing operation with an integrated portfolio of mines, concentrators, smelter, and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets > An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated > An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the owner's team.

Jan 1, 2013

By E. Dadzie

This paper will review some methods used to manage geotechnical risk at Damang Pit Cutback. The pit depth is designed up to 250m with push back on the eastern and western walls of the existed and depleted Railway Cutback (RCB) pit. The geotechnical design was presented by SRK Perth, focussing on the optimisation of the bench face angle which finally evolved with ?steep slope strategy?; 24m at 800 and 24m at 750 on the eastern and western walls respectively. The east wall was designed strategically to optimise the proximity of the tailings dam to the final pit crest of the push back. The pit has experienced failure in the weathered profile transgressing through the transitional material into the fresh rock at different location of the east wall since development in July 2005. To ensure stability and to minimise ore loss, the east wall has been redesigned using 700 batter angles and reduced berm width of 4m compared to 800 and 8.5 berm width of 24m bench height. The paper will also discuss how slope failures to the east wall had been sustained, managed and monitored to enhance production. Emphasis is placed on slope management at Damang which includes the principles of wall control blast, visual inspection, slope depressurisation and the state-of-the art of slope monitoring using Autoslope automated prism monitoring. Future slope monitoring is considering the use of 3D Laser and Radar to provide early warning so that evacuation could be effected. The intension is to provide mine personnel the means to identify risk areas during mining activities.

Jan 1, 2008

National Coal Board. Gate belt conveyors. London, H.M.S.O. (Price 95p.) Although the preface of this handy little book states that it has been written for the guidance of miningoperation trainees, it will prove valuable to the practising engineer as well. NIM reports Report no. 1733 A mineralogical investigation of weathered carbonatite from Salpeterkop. (14th Apr., 1975; re-issued 28th Feb., 1978). Report no. 1823 The recovery of gold and pyrite from a residue dump at Crown Mines. (10th Jul., 1976; re-issued 28th Feb., 1976). Report no. 1829 An investigation of weathered carbonatite from Salpeterkop. (20th Jul., 1976; reissued 28th Feb., 1978). Report no. 1932 A BASIC computer programme for the evaluation of intensity data from the Telsec Lab-X-250 Analyser. (12th Jan., 1978). Report no. 1940 The extraction of the noble metals with n-octylaniline,and its application to the analysis of platinum-bearing materials. (30th Jan., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). International futures conference A conference entitled 'The Road Ahead' is being organized by the 1820 Settlers National Monument Foundation to be held in Grahamstown from 3rd to 7th July, 1978. Conference of metallurgists The technical programme has been established for the 17th Annual Conference of Metallurgists sponsored by the Metallurgical Society of the Canadian Institute of Mining and Metallurgy. This year the Conference will be held in Montreal, Quebec, on 27th to 31st August, 1978, together with the 8th Hydrometallurgy Meeting.

Jan 1, 1978

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

By S. Tshikhudo

This paper outlines an investigation into the recovery of saleable fractions of coal from ?as-arising? South Export Plant effluent streams, using Baleen microscreening technology. South Export Plant, a subdivision of BHP Billiton Energy Coal SA (BECSA) Coal Processing, is a two-module plant treating 2000 t/h. The nominally -150 µm coal is untreated and is therefore passed from classifying cyclones to the thickeners for process water recovery. The thickened underflow is pumped into a series of slurry cells for further settling and recovery of supernatant water. The marginal quality, moisture content, and handlebility of this settled material renders it unsuitable for inclusion into saleable products and it is thus stockpiled and trucked to designated pits for disposal. Over the years, stockpiling and trucking has become an overly expensive exercise. In an effort to recover some of this cost, a task team was assigned to investigate less costly options to process slurry across BECSA plants. Various technologies such as froth flotation, sieve bends, and Reflux Classifier were considered, although the results were generally not beneficial ? this could be attributed to weathered/oxidized coal. A decision was made to pursue an alternative approach by testing the suitability of the new ?Baleen Filter?. The concept is to screen out the higher-grade fraction (+50 µm) as saleable product and reject the finer fractions to the slurry ponds. The Baleen Filter was found to effectively screen at an acceptable efficiency between 94% and 99.99%, with a very sharp cut-point (d50 and Ep). The actual yields from the screening results were better than the predicted yields in terms of both mass and energy as predicted from feedstock analysis.

Jan 1, 2014

By F. H. Cornet, D. Ask, O. Stephansson

We have conducted a stress analysis of overcoring stress measurements undertaken at the Zedex Test Site (ZTS) in the Äspö HRL, Sweden. Two different types of overcoring cells have been used at the site: the 9-gauge Borre Probe (CSIR-type) and the 12-gauge CSIRO HI cell. Inversion programs based on the least-squares criterion were developed and calibrated. The primary and secondary stress field in the ZTS were back-calculated using strain data from individual cells as well as from combining data from both cells. We propose that the combination of strain data from the two cells significantly improves the determination of the stress field. A striking result is the good agreement between the re-analysed overcoring data and the existing hydraulic fracturing data. The deviations for the horizontal stresses between the re-analyzed overcoring data and the existing hydraulic fracturing data are approximately 3 MPa. The deviation in the orientation of maximum horizontal stress is approximately 10-20°. Nous avons analysé les résultats de mesures de contrainte par surcarottage réalisées sur le site Zedex, du laboratoire souterrain HRL d’Aspö, en suède. Deux types de cellule de mesure ont été utilisés sur ce site : la cellule à 9 jauges (du type CSIR) et la cellule à 12 jauges (du type CSIRO HI). Un programme d’inversion mettant en œuvre une norme par moindres carrés a été développé et validé. Les champs de contrainte primaires et secondaires du site Zedex ont été évalués d’une part en considérant chaque mesure isolément, d’autre part en intégrant l’ensemble des données de déformation dans une inversion unique. Nos résultats suggèrent que l‘association des diverses mesures dans une intégration unique améliore nettement la détermination du champ de contrainte. Un résultat intéressant est le bon accord entre ces nouveaux résultats et les résultats des mesures par fracturation hydraulique. Les écarts sur l’amplitude des contraintes horizontales est de l’ordre de 3 Mpa, les écarts sur les orientations de l’ordre de 10-20°. Auf dem Zedex Test Gelände im Äspö Festgesteinslabor (HRL) wurde eine Spannungsanalyse mittels Overcoring Spannungsmessungen durchgeführt. Hierzu wurden zwei verschiedene Methoden verwendet: das 9-kanal Borre Gerät (CSIR- Ausführung) und die 12-Kanal CSIRO HI Zelle. Inversionsprogramme, die auf dem “least-squares”- Kriterium basieren, wurden entwickelt und kalibriert. Das primäre und sekundäre Spannungsfeld des Zedex Test Geländes wurde sowohl aus Verformungsdaten individueller Zellen als auch aus Kombination beider Zellen ermittelt. Wir nehmen an, daß die Kombination der Messergebnisse beider Geräte die Bestimmung des Spannungsfeldes signifikant verbessert. Überzeugender Beweis hierfür ist die gute Übereinstimmung der überprüften Overcoring Daten und Ergebnisse aus existierenden Hydraulic Fracturing Versuchen. Die Abweichungen der horizontalen Spannungen aus beiden Datensätzen ist etwa 3 MPa und Abweichungen der Orientierung der größten Horizontalspannung liegen bei etwa 10-20°.

Jan 1, 2003

[Consider the situation where we wish to estimate the value of a block of ore W from the values of n samples wt (i = 1, 2.... n). The samples can be located anywhere inside or outside W. The blocks and the samples can have any size or shape (Fig. 8.1). We define ws as the set of all the samples wi: WS = Iw1; W2; W3.. . wn and we wish to estimate the block W using the samples ws. Let xi be the value of the ith sample and µw the unknown average value of the block. We can estimate µw from the average value of all the samples. Let µw be the estimator of µw. As the samples need not be of equal size, the sample average is: µw = wi xi/~ wi. (8.1) The mean squared error made when estimating µw by µw is known as the variance of estimation of W by ws. It is the error made when giving the value of the sample set ws to the block W and is written o2E (WS to W). By definition: o2E (ws to W) = E [(µw - µw)2]. (8.2) If n = 1, this error is known as the extension variance. Since the sum of the weights given to the sample values is equal to 1,0, the estimator µw is unbiased (the question of the absence of bias is studied in more detail in Chapter 9): E [( µw - µw)1 = 0. (8.3) The error (µw - µw) has zero mean and a variance o2E = E (W8 to W). If we assume that this error is normally distributed, we can define confidence limits for µw. Let tP be the value of the standardized normal variance t such that the probability that t is less than tP is p: (t,) = .\/27T f exp (- t2/2) dt = p (8.4) The probability that µw is larger than µw + t1-P oE is p. The probability that µw is smaller than µw- t1-P oE is p. The following approximation formulae are often used to calculate 2p central confidence limits for the block value: 68% central confidence limits (p = 16%): µw - o2E, and µw + o2E. 95 % central confidence limits (p = 2,5 %): µw - 2 oE, and µw + 2 oE. Tables of the function 0 can be found in any textbook on statistics (for example, Fraser, 1958, p. 388) (see Table 7.2). [ ] The last line of Table 2.2, corresponding to f = 00, also contains the value of tP for p = 80, 90, 95 and 97,5 %.]

Jan 1, 1978