Search Documents

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By I. V. Lunkin, E. B. Muhamedzhanov, A. B. Begalinov, B. R. Rakishev

Almost all the ore deposits of ferrous, non-ferrous and rare metals of Kazakstan, are exploiting by the open-cast method, are the complex-structural, multi-component ones. Their rational working requires precise organization of extracting works. In this connection it is necessary to set up the best intercommunications between drilling-blasting, excavating-loading and transport works. This requires the stable functioning of the quarry for dispatch of ore raw material of required quality with minimum of corresponding expenses. For this purpose, proceeding from the quarry’s ore output and the assumed parameters of the exploitation system, the first problem about rational arrangement of excavating-loading equipment in extracting faces is solved. By solving the problem the model with dynamic, adapting properties had been used. It was solved numerically by the method of statistical tests. By setting up the necessary link between type-sizes of excavating-loading and transport equipment, the minimum prime cost of loading and transportation of 1 ton of mining mass from the face to the receiving station was adopted as the criterion of optimality. Depending on the type of excavating-loading equipment, the efficiency function may be different. By using wheel loaders, their displacement between the faces is possible, therefore, the efficiency function of the problem may include expenses for their displacement. By using excavators like power shovel, the problem’s restrictions must exclude its displacement between the faces. The efficiency function consists of minimum expenses for loading, proceeding from set of volumes of extraction from the faces, satisfying required quality. The volumes of extraction from the faces, satisfying required quality of ore in output stream, are determined by the method of statistical tests. Sample range is given, proceeding from the restrictions for maximum productivity of the excavating-loading equipment. Volumes of extraction, not satisfying required quality, are cut off. The efficiency function meaning is then determined and minimized. Keywords: Excavating-loading equipment, its placing in extracting faces, optimal load-carrying capacity, specific expenses for loading and transportation of mining mass.

Jan 1, 2003

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

By R. Degel

Submerged arc furnaces and electric smelters are applied in numerous metal and slag production lines. Particularly in ferroalloy and non-ferrous metal production, like silicon metal, platinum group metals, calcium carbide, and copper, the units are an essential part of the production technology. Most of these electric furnaces are considered to be highly energy-intensive units. The high level of required electrical power is defined by the process. SMS developed several measures to reduce the overall electrical energy consumption of these metal production lines. In particular, the following measures contributes to a lower energy consumption: improved electrical efficiency with intelligent design and application of components, minimizing the heat losses from the furnaces with a balanced cooling/refractory systems, minimization of process steps (such as elimination of agglomeration), recovery of energy, process optimization (resulting in higher metal yield) and the achievement of higher recovery rates, enlarging furnace capacity to reduce heat losses, and maximizing the power-on time. This paper gives an overview of the above-mentioned solutions.

Jan 1, 2012

By B. M. Thethwayo

Graphite blocks are currently used in the concentrate - slag zone in primary PGM smelters, and can possibly be extended to the matte zone. This project evaluates the interaction between synthetic matte and graphite blocks on a laboratory scale. Static crucible tests were performed where graphite crucibles (prepared from standard and high-grade graphite) were filled with synthetic matte (27.7 per cent S ? 46.1 per cent Fe ? 17.0 per cent Ni ? 9.2 per cent Cu) and heated to 1550°C for different time periods (1?5 days). Matte penetration was evaluated using a SEM, while graphite dissolution was evaluated by measuring the carbon content of the matte with a LECO carbon analyser. Matte penetrated into standard grade graphite up to approximately 2 mm, while matte infiltration into the high grade graphite was limited to the immediate hot face. The saturation solubility of graphite in the synthetic matte at 1550°C was 0.43 per cent. Copper, iron, nickel, and sulphur were detected in an accretion that formed in the water-cooled part of the furnace. This accretion consists of mainly Cu-S and Cu-Fe-S based phases.

Jan 1, 2012

By F. Smit

Mining and plant disciplines can benefit from pre-concentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of pre-concentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2012

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By C. Dorfling, M. Tadie, S. Grobbelaar

The physicochemical properties of the complex electrolytes used in direct copper electrowinning are an important consideration for the development of a high-fidelity model of the process. Direct electrowinning electrolytes typically contain a high background of metallic impurities. The effect of metallic ions on the properties and accompanying change in the limiting-current density for copper reduction have been the subject of several studies. Although various empirical correlations have been published for describing the physicochemical properties of electrowinning electrolytes, the correlations are only applicable to a limited range of conditions and cannot be extrapolated without further validation. Consequently, in this paper we validated existing physicochemical property correlations for the full range of operating conditions applicable to direct copper electrowinning and developed a new correlation for predicting the associated limitingcurrent density for copper deposition. Following, we evaluated the benefit of using the validated correlations as a component of a dynamic electrowinning model.

Jan 1, 2023

By Z. Saw, C. Poveda, N. L. Mai

Optimising the throughput of a mining network comprising all equipment from shovels to semi-autogenous grinding (SAG) mills is a complicated task, yet the potential benefits can be significant. Key modelling challenges stem from the sheer number of possible routes which material can travel, different equipment operating under different constraints, and the rate of SAG mills being calculated through a nonlinear function of the blended materials’ rock attributes. Nevertheless, this is an ideal onapplication area of mathematical programming, a branch of operations research. This paper describes an application of mixed integer linear programming (MILP) to optimise the mining equipment network of one of the world’s largest copper mines.The model takes as input a year-long monthly mine schedule of shovels in different pits, pushbacks, sequences and faces which produce material to be moved through a network of crushers, conveyors, silos, distributors, stockpiles and SAG mills, ultimately outputting a daily operational plan for all equipment that maximises the throughput of the network. All operational constraints and business rules are considered, including three quality attributes of copper ore. Comparing model results with actual data shows an improvement of 4.47% in network throughput tonnage. Additionally, although the model is solved using a free, open-source solver, optimal solutions are still achieved within a practical timeframe.

Sep 1, 2021

By O. Koatlhai

Mine closures have traditionally prioritised environmental rehabilitation, often overlooking the deep socio-economic disruptions that follow, particularly in mining-dependent communities. This paper argues that mine closure should not mark the end of prosperity but rather the beginning of a sustainable transition. The coproduction model, which integrates community participation, governance, and economic planning, offers a transformative approach to closure planning. Drawing on case studies from Ghana, Zambia, and Indonesia, this research examines the successes and failures of past closures, highlighting the critical role of stakeholder engagement, skills development, and economic diversification. By incorporating emerging technologies such as AI-driven economic forecasting, blockchain for governance transparency, and decentralised finance (DeFi) models, mining companies can ensure a just and sustainable post-mining future. This study challenges outdated closure models and presents a forward-looking strategy that sees mine closure not as an endpoint, but as a catalyst for social resilience and economic transformation. It underscores the need for policy reforms, stronger governance, and investment in alternative industries to prevent mining towns from becoming economic wastelands. By shifting the paradigm from remediation to regeneration, this research calls for a new era of mine closure planning that puts people and prosperity at its core.

Apr 25, 2025

By W. Gabryk

A large new underground platinum mining project required that all different mining options were investigated during an option study before proceeding to the prefeasibility stage of the project. The capital project team identified 21 different options requiring investigation. These options considered 10 different access methods and 4 different mining methods. Each of the 21 options required a mine design, a valid production schedule, and the associated economics in order to facilitate a comparison on project Net Present Value (NPV) and other metrics. The project sponsors required this work to be completed in 3 months and therefore the project team decided to adopt an object-oriented modelling approach as implemented by Cyest Corporation. This would allow all 21 options to be valuated within the tight time frame due to the generation and re-use of templates. Standard objects were configured into templates containing the mine layout, design, and scheduling logic. These templates could then be assembled into a model to represent the option being investigated. The adoption of rules-based design and production scheduling then allowed for the rapid generation of a valid production schedule for each option with different iterations of varying production ramp-up and mining efficiency assumptions. The activity-based operating costs, labour, and capital were also linked to the standard templates such as a half level or barrel, which were then replicated to represent the overall mine structure for each option under consideration. Using this approach for each option, a full production schedule was produced per mining activity, the operating costs were calculated using activity-based costing, an infrastructure capital expenditure estimate was determined, the development capital requirements costed, and an overall NPV determined. This options study was completed in an unprecedented 10 weeks and a recommendation was put through to the Business to take three of the options to the next study phase.

Jan 1, 2012

By H. Mulder, M. C. Bekker

The objective of this paper is to describe the research followed in creating a generalized, readiness assessment tool for mining projects. We start by highlighting the need for the assessment tool and then progress towards explaining the methodology followed during the study. The selection and finalization of the list of elements, sections, and categories that make up the unweighted values are described, followed by a summary of the weighting process applied. The outcome of this process is a weighted readiness assessment tool for mining project studies. The main benefits of the tool are that it will guide decision-makers and project managers through the definition phases of the project and improve the likelihood of project success.

Jul 2, 2022

By A. Singh, K. Bisaka, G. Marape, T. Mokgomola

This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of TREEs, no flowsheet improved their grade.

Nov 6, 2024

By J. Pelders, G. Nelson

"Fatigue is a significant concern in the mining industry as it is a causal or contributing factor in many incidents and accidents. Fatigue can be caused by work- and non-work-related factors. There is a lack of information about associations between demographic and other non-work factors, and fatigue. This study aimed to assess associations between demographic, work, living, and socioeconomic conditions, and lifestyle characteristics, and fatigue at a platinum smelter in South Africa. Eight interviews with management and two focus groups with production workers were conducted, and 75 questionnaires were completed by production and other workers. Both work- and non-work-related factors were considered to be causes of fatigue. These factors included overtime, shift work, high workloads, activities performed outside of work, age, race, housing tenure, diet, sleep disorders, stress, and job satisfaction. In general, higher levels of fatigue were reported by younger participants, those who rented accommodation, ate less healthily, had a sleep disorder, and those with high levels of stress and low job satisfaction. As various demographic, lifestyle, and wellness-related factors were associated with fatigue, both work and non-work contributors should be addressed in fatigue management plans. BackgroundFatigue may be defined as ‘a state of impaired mental and/or physical performance and lowered alertness arising as a result of, or a combination of, hard physical and mental work, health and psychosocial factors or inadequate restorative sleep’ (BHP Billiton, 2005). Williamson et al. (2011) define fatigue as a biological drive for recuperative rest. Sleepiness and fatigue are related, and the terms are often used interchangeably. However, sleepiness, more specifically, can be defined as sleep propensity, or a person’s tendency to fall asleep (Hossain et al., 2003; Shen, Barbera, and Shapiro, 2006).Increasing levels of fatigue and sleepiness are associated with lapses in attention, errors, response slowing, fluctuations in alertness and effort, and impaired attention, working memory, long-term memory, decision-making, and creativity (Alhola and Polo-Kantola, 2007; van Dongen and Dinges, 2000). Fatigue is also associated with adverse effects on mood and impulsive behaviours (Alhola and Polo- Kantola, 2007; Minkel et al., 2011; Schwarz et al., 2013). It is a significant concern in the mining industry as it is commonly identified as a causal or contributing factor in many accidents and injuries (Schutte, 2009). Fatigue can also lead to long-term health problems, including digestive problems, heart disease, stress, and mental illness (Shaw, 2003)."

Mar 1, 2019

By M. Shamsi, M. Nehring

One of the most challenging aspects in semi-mobile in-pit crushing and conveying (SMIPCC) system design is determining the optimum depth at which to change from a purely truck-based haulage system to a conveyor-based haulage system. We used scenario analysis to determine the optimum transition depth between a truck and shovel (TS) system and a SMIPCC system. Traditional pit-limit algorithms were used to generate the final pit limit on a copper deposit, which was then divided into four pushbacks. The final operating pushbacks (phases) were designed for both TS and SMIPCC. The end depths for each phase are viewed as candidate transition points to switch from the TS to SMIPCC haulage system. Economic calculations were applied for five different scenarios, including adopting SMIPCC from the outset (pure SMIPCC), after the first, second, and third phases, and finally not using the SMIPCC system (pure TS) at all. The analysis indicates that the second scenario, at a depth of 335 m, results in the lowest cumulative discounted cost (CDC). In this case, the CDC is 17.6% lower than that for the pure TS scenario and 10.7% lower than for the pure SMIPCC system scenario.

Sep 1, 2021