Search Documents

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magnetohydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2015

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By Ri McCrindle

"Analytical Chemistry is moving rapidly towards a concept where technicians have to do no more than press a button and print the result from an instrument that is a featureless ""black box"". In this environment we must ask how much traditional ''wet chemistry"" is still required for undergraduate students.Methods that can be fully automated will become increasingly important. An example of such a method is that of the slurry nebulisation and ICP-OES analysis of precious metal concentrate. Grinding the sample and adding Triton X100 as dispersant, complete analysis time is in the order of 90 min as apposed to the traditional Carius tube method which could take as long as 24 h. For most of the elements studied, the results using ""in-house"" reference material for calibration and as samples as well were within the 95% confidence level. Elements of low concentration in the sample (As, Bi and Se) were not within that level."

Jan 1, 2014

By A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents possibilities of reducing methane emission to the atmosphere in working mines in Jastrzebie Coal Company by means of proecological solution. They form a new approach towards the problem of rational and effective use of natural resources both in economical and environmental respect. Power and thermal energy for underground air conditioning in mining excavations are produced from the methane, which is drained out of the mine for safety reasons.

Jan 1, 2003

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By J. Thompson

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree A study into the stability of strike gullies at TauTona mine was to be carried out. In reaching the conclusions to follow, a three-stage process was followed. ?A literature study as well as discussions with management and workers alike to gain their inputs and perceptions. ?An ESH Department survey into the history of transgression from proper mine standard in TauTona strike gullies. Unfortunately records were found to be scarce and obscure and the importance of better inter-departmental recordings cannot be stressed enough. ?An underground survey of 11 pre-selected gullies distributed in both the UCL and LCL reef horizons. This stage is to carry the greatest weight in the points to be brought forward in this report. The process highlighted and ranked the following areas as the most critical role players in the deterioration of strike gullies: ?Poor blasting practice ?Sub-standard siding depth and lead-lags ?Split sets ?Off line gully development ?Adverse geological features. The following has been suggested to the mine to help reduce strike gully instability. ?Where possible, maintain lead-lags below 7 m?else increase the siding depth to suit. ?Decrease the gully width standard to 1.2 m (especially in ?high risk areas?). ?Discourage drillers from drilling side holes in gully face blast pattern. This will allow for time in which tendon support can be kept up to date. ?Ensure split sets are installed 1 m behind the gully face so as to prevent opening up of fractures. ?Utilize the centre split set in the 1:2:1 pattern to maintain the proper gully line. ?When adverse conditions prevail, it is necessary to apply a special support plan not only to the panel face, but also (just as importantly) to the gully as well. Shotcreting of the gully hanging is a suitable long-term consideration for providing the additional a real coverage needed. List of Abbreviations [CL Carbon Leader M/O Mine Overseer UCL Upper Carbon Leader FOG Fall of Ground LCL Lower Carbon Leader H/W Hanging Wall ERR Energy Release Rate F/W Foot Wall WDL Western Deep Levels ESH Environmental Safety and Health ]

Jan 1, 2002

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

Rock engineering has now been practised as a discipline for about50 years, and many sophisticated methods of analysis for use in rock engineering design have been developed. However, analysis is only a tool for use in engineering design, and rock masses are often so complex that realistic modelling of them, even with sophisticated methods of analysis, is impossible. At the other end of the scale, rock mass classification methods have been developed to quantify the rock mass. These ?numbers? are now widely used for assessment of stability of underground and surface excavations in rock, for the determination of rock support requirements, and for the estimation of rock mass strength and deformation properties. In considering these areas, the two concepts?design, and prediction of behaviour?will be dealt with. The discussion will be introduced by a consideration of the characteristics of the rock mass, which will highlight the variability in its properties and hence the uncertainty in the behavioural parameters. Examples of real projects will be used to illustrate the discussion.

Jan 1, 2003

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

By P. Sharma

Longwall panels facing wind blasts have been investigated at both Newstan and Moonee Collieries in the Newcastle Coalfield under the Wind Blast Project of the School of Mining Engineering, The University of New South Wales. The fluid mechanics involved in the compression and expulsion of air during wind blasts have been defined and the overpressure and air velocity time histories utilized to determine the wind blast parameters and define the relationship between them. The characteristics of wind blasts pressure pulses in mine roadways show some similarity with transient phenomenon like air blasts from explosives and shock waves from the failure of pressurized vessels. The peak wind velocities in roadways, however, exhibit marked deviations from theoretical predictions based on compressible fluid flow and Rankine-Hugoniot relationships applied to goaf air displacement and panel geometry. Peak overpressures and wind velocities have shown a positive correlation with the areas of goaf falls, with the values peaking off for larger areas. The field investigations have helped the mine management in risk assessment and in evaluating the success of induced caving by hydrofracturing to mitigate the hazard.

Jan 1, 2004

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014