Search Documents

By R. E. Gürtunca, D. J. Adams

Writen contribution by J.F.Curtls The subject mater of the paper is interesting in that, instead of 'numerical modeling based on elastic theory' being used for the prediction of energy release rate (ERR) in relation to various types of stope support, including backfil, use is made of stresses in the backfil in an atempt to corect the numerical modeling. Authors' reply to J. F. Curtis We thank Mr Curtis for his contribution to our paper. First of al, it should be emphasized that the object of the paper is not to address the validity of ERR as a tool for the assessment of seismic events or rockbursts, but to determine an in situ modulus for the rockmass with the aid of backfil measurements. Writen contribution by T.R. Stacey Although the authors of the above-mentioned paper have presented some good and interesting information, the title of the paper, and the recommendation that such an in situ modulis should be used for calculations of energy release rate (ERR), are viewed with some concern. The reasons for this concern are as follows. Authors' reply to T.R. Stacey Dr Stacey's comments on our paper are appreciated; we should like to address his concerns as follows.

Jan 1, 1991

By C. L. M. Gough, L. A. Vermeulen, D. D. Howat

Formulae expressing the dependence of the mass of a grinding ball on the amount of material milled by a ball mill are derived. It is shown that, with the aid of these formulae, it is relativel rsimple for the results of a marked-ball test to be analysed and for the relative performance and cost-effectiveness 0 the various types of ball under test to be evaluated. Predictions based on theory and the results obtained in a marked-ball test in a ball mill are compared detail and shown to be in close agreement. The difficulties associated with marked-ball tests are considered, and an explanation for the decrease in the calculated consumption of the balls, which follows naturally from the theory, is presented. The marked-ball anomaly explained, and it is demonstrated that the ball consumption in a ball mill can be predicted with fair accuracy from the results of a marked-ball test.

Jan 1, 1983

By N. Sinclair

"In open pit dozer bulk push operations, the material left resting against the highwall after blasting poses an issue. This is because dozers cannot physically get in behind the waste to begin the bulk pushing process. Instead, an excavator can be used to side-cast this waste for the dozers to access. An alternative technique is to have the dozers ‘side-cut’ the material, which involves the dozers running parallel to the wall, digging out the material, and eventually rotating their blades to begin bulk pushing. Industry practices suggest the latter technique is less productive and economical than using an excavator. However, such excavator sidecasting ‘economic viability’ assumes that smaller/ancillary type excavators are used (i.e. less than 23 m3 bucket capacity). So, what happens if some mine sites are restricted to using relatively larger excavators (> 23 m3 bucket) that are preferred for higher priority digging tasks? When can they avoid using their excavator? This paper explores multiple scenarios that have been designed and developed to simulate data results, which identify conditions in which the dozer side-cutting technique becomes more economically viable than excavator side-casting in terms of decreased unit cost per loose cubic metre. IntroductionOptimizing the cost of waste removal operations is important for the profitability of opencast coal mines. In the past decade, dozer bulk pushing has emerged and taken over from traditional waste removal operations such as dragline and truck-and-shovel methods at various sites around the world (Beatty, 1994). In a typical bulk push operation, once the bench has been blasted, waste is left resting against the highwall, which can either be cleared using a loading unit or by having the dozers ‘side-cut’ the highwall.Dozers perform most effectively when slot dozing side-by-side, perpendicular to the highwall. However, when dozers are required to remove material off the highwall, they must push parallel to the highwall, rather than perpendicular, hence ‘side-cutting’ the material to ensure a clean face. While dozer sidecutting is possible, it has been found that the majority of mine sites use a loading unit in this situation to avoid dozer inefficiency. Other perceived issues with dozer side-cutting include higher maintenance requirements and safety risks to dozer operators working in close proximity to the highwall."

Jan 1, 2019

By R. C. Urquhart, W. P. Channon, D. D. Howat

Discussion: The mode of current transfer between electrode and slag in the submBerged-arc furnace by w. P. CHANNON, R. C. URQUHART, and D. D. HOWAT J. MEINTJES I have read the paper with much interest, and I should like to make a few observations. (I) The experimental work deals with resistance heating by an electrode immersed in a slag... AUTHORS' REPLY We thank Mr Meintjes for his critical analysis and helpful comments arising out of his study of our paper. Possibly we should emphasize at the outset that our experiments all related to the conditions in which the lower portion of the electrode was immersed in molten slag. We believe, however,

Jan 12, 1974

By J. Petersen, T. Moyo, J. Dinga

The leaching of chalcopyrite in ferric sulfate media is notorious for its slow and inhibited kinetics. Different methods have been proposed to improve the kinetics, including the use of organic compounds as additives to the leaching media. In this study, the enhancing effect of methanol, ethanol, 1-propanol, and 2-propanol on the leaching of chalcopyrite in aerated acid ferric sulfate solutions using different reactor systems was investigated. The results revealed a clear improvement of copper dissolution by methanol and 1-propanol relative to tests with no additives under similar conditions. Operating a continuous-flow mini-column reactor yields surprisingly good results, potentially related to the maintaining of a consistent leaching micro-environment on the mineral surface. Scanning electron microscopy studies showed that the alcohols result in the removal of surface deposits formed during the anodic dissolution, potentially thus facilitating improved cathodic reduction of the ferric ion to drive the anodic dissolution.

Jan 1, 2023

By G. Song, S. Yang

"SynopsisThe development of techniques and equipment for single-pass high-seam longwall mining in China is reviewed. Some methods used to obtain the fractured zone height are discussed. The boundary between the caved and fractured zones is generally not clear, but one important difference that distinguishes the two zones is that horizontal compressional forces exist only between blocks of fractured zone. Based on this, a theoretical method is presented to investigate the destabilizing modes of the main roof (by sliding or rotation) and is used to determine if the main roof is in the caved or fractured zone. This method considers the mining height, immediate roof thickness, bulking factor, main roof thickness, main roof strength, main roof periodic weighting interval, and vertical stress in the overlying strata. To verify the method, a representative physical model of Wangzhuang coal mine is developed. The movement of overlying strata and fractured zone height are thus obtained. According to the results, the total collapsed height of the strata reaches about 70 m above the coal floor; the first main roof bending interval is 45 m and periodic bending distance is 10–15 m; the maximum strata subsidence is around 62 mm; and the presence of a three-hinged arch causes the fluctuation of subsidence in the same stratum level. Based on the theoretical and experimental analysis, the middle of the main roof is considered the boundary between caved and fractured zone; the caved and fractured zone heights are about 21 and 49 m respectively.IntroductionThick coal seams (>3.5 m) account for about 44% of the coal rescource/reserves and more than 40% of the total annual production in China (Zhao 2004; Wang 2009). Three mining methods – slice mining, top coal caving, and single-pass high-seam longwall mining – are frequently used in underground thick-seam operations. Compared with slice mining and top coal caving, high-seam single-pass longwall mining significantly simplifies the mining processes, reduces roadway excavation, and improves coal production, productivity, and recovery. The favourable economics, high production, and technical simplicity make high-seam single-pass longwall mining one of the most popular underground mining methods for thick coal seams in China."

Jan 1, 2015

By H. M. Friede

A study was made of the smelting process in two experimental furnaces patterned on Iron Age furnaces excavated at Melville Koppies Nature Reserve, Johannesburg. In a number of smelting experiments, the influences of air supply, temperature, time of operation, fuel consumption, and other operational factors were investigated. Metallurgical and metallographic aspects of the furnace operation and smelting products are discussed, and the experiments are compared with similar research work conducted in Europe and Africa.

Jan 1, 1984

An investigation into the stability of large open stopes at Premier diamond mine, Culinan, South Africa, is described. The open stopes are located in a weak kimberlite orebody, directly underneath a 75 m-thick sill of gabbro. Two and three-dimensional stress analyses were carried out in a back-analysis of the stresses and failure around the first open stope created under the sill. The results were used in the prediction of the future stability of the planned open stopes, intervening pillars, and sill.

Jan 1, 1987

By S. C. Thorley, J. R. Menasce

Trackless mining in low profile (LP) and extra low profile (XLP) platinum stopes has forced equipment designers to re-evaluate their equipment profiles to match the undulating reef. Low profile equipment designed to work in conditions with smooth and flat floors will simply not function with undulating floors and roofs and will become wedged between the floor and roof, beached on undulations due to lack of ground clearance, or suffer excessive mechanical damage. Tyres, too, need special evaluation, as conventional tyres for trackless mining do not work in an extra low profile environment.

Jan 1, 2004

By O. L. Papendorf

The method presented in this paper can be used, instead of lengthy cash-flow determinations, for the calculation of present values in the face of physical growth and inflation.

Jan 1, 1981

By C. E. Feather, G. M. Koen

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER B.Se. Hons. (Cape Town)* and G. M. KOEN D.Se. (Pretoria)* A description is given of the nature and occurrence of gold at various stages in the process of its recovery from Witwatersrand and related ores. Electron microprobe investigations show that the surface of gold grains in the ore is already coated. During metallurgical processing, further coatings, mainly hydrated iron oxides, accumulate on the grains. Theories are advanced for the formation of these coatings, and the adverse effects on metallurgical operations are discussed.

By D. D. Marsden, L. E. Kun

Although a regulation is in force that all water used underground shall be free of bacterial contamination, in practice it is often very difficult to accomplish this. The standard method of disinfection m South African mines IS treatment with calcium hypochlorite, although liquid sodium hypochlorite is used at a few sites. Primarily because the process depends on human control for the addition of the hypochlorite and the regulation of its now, it is frequently found difficult to disinfect mine water adequately and continuously. In many marine environments, chlorine generated by the electrolysis of seawater in its passage through an electric cell is used for disinfection. The generation procedure is continuous and needs no human control except for occasional checking of the equipment. This paper describes the successful implementation of the process, suitably .modified, .at four underground sites. After severe scaling problems had been overcome, a procedure resulted that chlorinates considerably more effectively than the previous system (dosing with calcium hypochlorite), and that has a lower amortized operating cost.

Jan 1, 1981

By M. J. Southwood

SYNOPSIS Experiments carried out under atmospheric pressure and temperature (25°C) and sterile conditions show that the dissolution rate of nickel and copper from a pyrrhotite-pentlandite-chalcopyrite ore in a lixiviant of sulphuric acid is greatly enhanced in the presence of pyrite. At a pH value of 1,8 and in the presence of pyrite of equal mass to that of the ore, the recoveries of nickel and copper improved dramatically (21 and 80 per cent respectively). At a pH value of 4,0 the recovery of nickel was enhanced, but the chalcopyrite was refractory. A galvanic mechanism is probable, but cannot be proved from these experiments. The economic implications of the results are discussed.

Jan 1, 1985

By J. S. Preston

The properties of some recently developed solvent-extraction reagents for the separation of cobalt and nickel sulphate solutions are reported. New commercial extractants based on alkyl phosphonic and alkyl phosphinic acids are described. These reagents show much improved selectivity for cobalt compared with established extractants. Some novel extractants developed at Mintek for the selective recovery of nickel in the presence of cobalt are also described. These reagents, which are based on mixtures of carboxylic acids and non-chelating oximes, are of interest in that no commercial nickel-selective reagents are currently available. Graphs showing metal loading and stripping, and pH-functionality, are presented. together with details of the metal separations achieved in batch countercurrent- extraction experiments with the various reagents.

Jan 1, 1983

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

This paper describes experimental investigations into the reductive decomposition of arsenopyrite/pyrite (FeAsS/FeS2), a gold and silver bearing iron/arsenic sulphide using metallic iron powder. The main objective was to establish and experimentally confirm the thermodynamic and kinetic feasibility of reductively decomposing the sulphide matrix for precious metals recovery. In this context, cyanidation leach tests were conducted on the reductive leach residues. The arsenopyrite/pyrite flotation concentrate, mainly studied in the hydrochloric acid medium, decomposed through the non?oxidative chemical dissolution reaction and the reductive decomposition reaction for the arsenopyrite and pyrite components, respectively. Desulphurization levels below 65% were achieved at pH values below 0.15 and iron to concentrate ratios above 1, and the system was characterized by overall very slow kinetics. The reaction system had a direct linear relationship with iron to concentrate ratio and an inverse relationship with pH. An analysis of the pyrite/iron galvanic system showed that pyrite forms a partially inert cathodic surface on which the anodic dissolution of iron occurs, supported by the hydrogen evolution reaction. This phenomenon explained the low desulphurization levels and the mineral decomposition seemed to be restricted to the non?oxidative chemical dissolution reaction for the arsenopyrite component. The cyanide leach of the reductive leach residues showed very little improvement in gold recovery. The reductive leach process for arsenopyrite/pyrite has considerable limitations in terms of both desulphurization and precious metals liberation. Keywords: Pyrite, arsenopyrite reductive leaching, hydrogen sulphide, invisible gold

Jan 1, 2009

By J. H. Venter

The accuracy of estimation from samples of ore in bulk By J. H. Venter Published in the Journal April 1972. ERRATA: Equation (1) should read... Equation (3) should read .... line following "Duscussion" Delete" .... Insert... above "References" "Discussion". Replace .... tenth DISCUSSION M. DA VID Professor Venter has proposed a formula to compute the variance of the estimated grade of a lot of broken ore, and interesting comments on the relevance of the formula and suggestions for developments are made by P. R. Janisch.

Jan 4, 1972

By A E. Paterson

General aluminium corrosion charts based on 1100 alloy listing product and temperature have been developed by AFSA, mainly from available sources. The categories of corrosion expectation are fairly wide. As a result the charts are more useful in indicating what is not suited as distinct from what is. The question of how to develop useful information is assessed. Having discarded improbable options one is left with the need to refine the possible. Within each alloy group corrosion potential differs. From an engineering application point of view, the corrosion resisting marine alloys, the 5xxx series show increasing corrosion as the percentage of Magnesium increases. An important issue is that as the welding filler used for 5xxx series is Mg rich (to avoid hot cracking), the filler is likely to show the weakest resistance. In addition, when subjected to fatigue loading, the preference for critical joints is to dress the joint to the level of the base material. Overheating of the weld extends the HAZ zone and weakens the material as Mg moves to the grain boundaries. Indicator chart refinement approaches suited to aluminium use in commercial transport are discussed.

Jan 1, 2006

Discussion of the above paper by G. J. van JAARSVELDt Mr Ortlepp's paper is important, and deals with a subject towards which much controversy and insufficient basic scientific logic, in my opinion, have been directed. He attempts to remedy some of our unscientific popular misconceptions, and for this we thank him. However, I regret to say that experience has shown that some of his statements cannot be allowed to pass unchallenged. Author's reply Mr Van Jaarsveld's contribution is welcome because it provides an opportunity for me to clarify certain points that were perhaps not adequately explained in the paper.

Jan 1, 1979

By P. A. Roberts

A modified in situ leaching method for extracting gold from oxidized gold ores using a non cyanide lixiviant is proposed. A non cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide bearing solutions into the subsurface. Oxidized gold ores are the initial focus because earlier research on the use of sodium thiosulphate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulphate breakdown. A reconnaissance research programme, involving ore characterization and hydrometallurgical testwork on samples from four Australian ore deposits and preliminary reactive transport modelling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulphate and ferric EDTA, and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples under anaerobic conditions. The ore characterization and reactive transport studies, suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Physical permeability enhancement could be achieved by blasting and/or hydraulic fracturing of the ore. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in place leaching? has been adopted for the proposed gold extraction system

Jan 1, 2009