Search Documents

By S. Gqebe, A. Lewis, M. Rodriguez-Pascual

"Gravitational sedimentation of suspensions in various precipitation processes is hindered by colloidal stability. This is due to the high surface charge of the suspension and results in strong attraction/interaction between the ions on the particle surface and counter-ions in solution. Moreover, this strong interaction results in a charge build-up that renders the suspension stable. In order to induce gravitational sedimentation of these particles, a redistribution of ions close to the particle surface is required. We therefore sought to redistribute ions close to the particle surface by applying a magnetic field. This results in the reduction of interparticle electrostatic repulsive forces and a subsequent increase in the zeta potential of a suspension. For the purpose of this study, a copper sulphide suspension was used. Copper sulphide particles were exposed to a range of field strengths for set exposure times and their zeta potential was measured before and after exposure. All particles had an initial zeta potential value equal to or less than –40 mV prior to magnetic field exposure. A significant increase in zeta potential was observed, with values reaching a maximum of –16.5 mV when exposed to a 2 T field strength for 40 minutes. This is due to Lorentz ion shifts resulting from the Lorentz force exerted by the magnetic field on the particle surface. IntroductionMetal sulphide precipitation is a process for treating industrial waste streams with high residual concentration of mixed metal ions and acid mine drainage. This process has been reported to achieve higher metal removal compared with the industrially prevalent lime precipitation, due to the sparingly soluble nature of the metal sulphide precipitates formed. However, precipitation is governed by high levels of supersaturation which favour the formation of fine particles (Lewis, 2010). Consequently, some of the metal sulphide fines formed exhibit slow settling dynamics and thus tend to remain suspended in solution."

Jan 1, 2016

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By E. Mokgwamme, T. Goff, M. Mvalelwa, P. Spratt, P. Bezuidenhout, P. Nkosi, H. Joubert, G. de Villiers

Sibanye-Stillwater recently completed a partial sidewall rebuild on Furnace 1 at its Marikana smelter complex. The project involved matte taphole maintenance, which required the removal and subsequent replacement of 18 composite copper-graphite coolers and a section of the lower refractory sidewall. These composite copper-graphite coolers are a newly developed cooling design by Tenova Pyromet, and this rebuild project provided valuable insight into the performance of the composite coolers. The novel composite cooler design was implemented to serve as a safeguard against localised wear and corrosion in the furnace sidewall, particularly at the slag-concentrate interface, where chloride-accelerated sulphidation has been identified as a dominant degradation mechanism affecting the copper cooling elements. The composite cooler design is unique in that all the exposed sides of the water-cooled copper elements are fully encapsulated in graphite, which protects the copper from corrosive sulphur- and chlorinebearing gases and condensates. This sidewall cooling system was designed to improve corrosion resistance, stabilise freeze lining formation, and extend the campaign life of the furnace sidewall. The partial sidewall rebuild was executed during a planned maintenance shutdown with the main objective of replacing the matte taphole lintel bricks. This paper serves as a case study that compares and evaluates the operational performance of the composite coolers before and after the rebuild. The installation method is discussed to highlight the approach taken to ensure a sound installation while minimising downtime, as well as to present some lessons learned in the process.

Mar 6, 2026

By Monica M. Cole

The Empress nickel/copper deposit west of Gatooma in Rhodesia occurs within gabbro and amphibolite, disposed at the contact of a granodiorite stock (Barebottom Hill) and the surrounding greenstones of the Archaen Bulawayan System. The orebody has a pipelike form and a poor surface expression due to plantation of the area by Miocene (Africa) and later Victoria Falls erosion cycles. Barebottom Hill represents a monadnock remnant in the geomorphological surfaces while traces of the once larger Empress orebody have been removed. Limitations in soil geochemistry necessitated both studies of the vegetation ecology and the biogeochemistry of the area, both of which were anomalous. The use of geobotany was found to be restricted but biogeochemistry offers a most effective prospecting tool and was found to define the sub-outcrop of the ore-body more precisely than soil geochemistry since these methods reflect and differentiate anomalies emanating from bedrock mineralisation and those due to surface phenomena.

It is well understood that to develop wagon wheels with higher abrasion resistance, fracture toughness, and fatigue resistance, steels with lower amounts of inclusions need to be used. Clean steels are produced with technologies that minimize the amount of inclusions in the microstructure. The demand for cleaner steels is high, and lowering of non-metallic oxide inclusions and controlling their morphology, composition, and size distribution is vital. Reduction of residual impurity elements such as sulphur, phosphorus, hydrogen, nitrogen, and trace elements is essential in the production of cleaner steel. Material cleanliness is vital for fatigue endurance, since oxide inclusions may act as stress concentrators and initiation points for fatigue cracks. To better understand the relationship between the cleanliness and toughness of the 34-inch cast wagon wheels, two samples of different levels of cleanliness were supplied for investigation. This paper presents the results of metallurgical analysis using scanning electron microscopy(SEM), energy-dispersive spectrometry (EDS), and mechanical tests for the pearlitic high-performance cast rail wagon wheel (identified as Class B) that are currently being used. The Charpy V-notch impact test results for the three samples from wagon wheels were compared. With the aid of SEM/EDS analysis system, non-metallic inclusions in these steels were detected, and it was possible to determine the position, size, shape, and composition of each particle. Alumina and manganese sulphide inclusions could be identified as the dominant inclusion types in the investigated samples. Fracture surface analysis of the Charpy specimen with high inclusions indicated that transgranular cleavage was the predominant fracture mode. Fractography of fracture surfaces of Charpy impact test samples also showed improvement of toughness properties on the clean sample.

Jan 1, 2013

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By P. Maais

This paper gives an account of the development of a plant for the differential flotation of mixed sulphide ore, special reference being made to the separation of copper and zinc sulphides. The uniqueness of the geology, mineralogy, and metallurgy of each complex ore-body is stressed. Consideration is given to the scale-up of laboratory data, and to some of the factors involved in the design of milling and flotation plants for this type of ore. Process control and development are discussed, as are the human requirements for the optimum operation of a concentrator.

Jan 1, 1980

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By J. Petersen, K. Shaik

The traditional route utilised for the recovery of Platinum Group Minerals (PGMs) in South Africa involves the concentration of ore by flotation, followed by smelting to produce a PGM rich matte, which is then digested hydrometallurgically to solubilise base metals and Platinum Group Elements (PGE). HCl/Cl2 is conventionally used for PGE dissolution from concentrated material, which is an aggressive reagent associated with high maintenance costs as well as environmental concerns. Of interest is the leaching of PGMs directly from mineral ores, low grade concentrates and tailings in a cyanide-ferricyanide system as a more sustainable alternative. This system has shown favourable Pt recoveries among the Pt minerals, but with sperrylite (PtAs2) displaying highly refractory behaviour. The dissolution of sperrylite is investigated in a cyanide-ferricyanide system in the context of an electrochemical study involving OCP, chrono-amperometry and cyclic voltammetry. This approach allows the assessment of leaching characteristics as well as the investigation of surface passivation, which is believed to contribute to poor Pt recoveries. Some evidence is presented that such passivation is related to the formation of arsenide species on the mineral surface. Keywords: Sperrylite, PGMs, cyanide, ferricyanide, electrochemistry

Jan 1, 2020

By B. Amankwaa-Kyeremeh, W. Skinner, R. K. Asamoah, C. Greet

With the continuous increase in ore mineralogical complexity coupled with decreasing head grades, there is a need for mining industries to process large tonnages of material to meet global metal demands. Smarter, cheaper techniques are required to better map ore mineralogical variations proceeding to pre-concentration (flotation) stages for higher performance and metal recoveries. This paper is aimed at briefly reviewing previous studies on different selected ore mineralogy, with the focus on their pulp chemistry, to identify relationships which aid quicker flotation feed variation monitoring. Very little published work exists linking pulp chemistry parameters to flotation feed mineralogical variation. A successful application implies maximising grades at higher metal recoveries and reducing the cost of reagent for a better performing flotation circuit. Keywords: Mineralogical variation, flotation, pulp chemistry

Jan 1, 2020

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By T. Mützea, L. Schützenmeister, G. Kacheb

High-Pressure Grinding Rolls (HPGR) are employed in cement plants worldwide. Although the technology has been mastered in the majority of applications, design-, scale-up- and operationalchallenges still exist today. In addition to modelling throughput, energy requirement and comminution success, the prediction and avoidance of malfunctions is of great importance in current research. The performance of the mill is highly influenced by the roll speed and the fineness of the feed material. Another parameter influencing the composition of mill feed is the circulating load, which is determined by the grinding circuit configuration, the target fineness and the separation efficiency of the classifier. In order to meet this circumstance and simultaneously maintain a reasonable level of material input and testing effort, a complete grinding circuit on a small technical scale was set up in the research centre of Thyssenkrupp Industrial Solutions AG. The present study varied the roll speed (0.5-2 m/s) and the proportion of fines in the feed (0-75 %) in order to investigate the influence of both parameters on the finish grinding of a Portland cement with a target fineness of 4000 cm²/g according to Blain. The experimental results are compared with model concepts and critically examined with regard to their transferability to industrial plants. Keywords: Cement grinding, grinding circuit, HPGR

Jan 1, 2020

By L. A. Balzan, M. Kalicinski, F. Nieuwenhuys

GEOSCANs on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech's experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani's GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis. Keywords: Online analysis, real-time, process control

Jan 1, 2020

By L. L. Godirilwe, and A. Shibayama, G. Danha, K. Haga, Y. Takasaki

Selective extraction through leaching of an amorphous slag obtained from a base metal smelter plant in Botswana is investigated in this paper, where the main objective is to optimise the experimental variables that would result in the maximum selective extraction of the three base metals (Ni, Cu and Co) from the slag waste. Mineralogical tests showed that the sample is composed mainly of fayalite (Fe2SiO4), with a total entrapped metal sulphides content of about 1.0 wt.% occurring as fine occlusions in the fayalite phase. In our experimental program, we compare the effectiveness of two common leaching techniques. In the first method, we use sulphuric acid to carry out atmospheric beaker leaching tests, and in the second method we use high pressure oxidative leaching. The effects of acid concentration, oxidant addition/oxygen partial pressure and pulp density on metal dissolution rate are examined. The optimal Ni, Cu, Co extractions of 80.5%, 81.9 and 98% respectively were obtained under high pressure oxidative leaching conditions (150 oC, 0.6 M H2SO4, 0.5 MPa O2), with substantially low dissolved Fe of 9.6%, the majority of which was removed as jarosite in the residue. Atmospheric beaker leaching yielded poor extractions of Ni below 40% when sulphuric acid combined with hydrogen peroxide (1.0 M and 0.6 M respectively, 65 oC) were used for leaching, while Fe, Cu and Co dissolutions were each about 80%. Therefore, using high pressure oxidative leaching provides a possibility to effectively extract Ni, Cu and Co while producing an environmentally benign residue, thus alleviating the current adverse environmental issues associated with the abandoned smelter slag. Keywords: Slag, amorphous, fayalite, atmospheric beaker leaching, high-pressure oxidative leaching, extraction

Jan 1, 2020

By Y. Zhang, F. Zhu, Y. Zhao, L. Dong, Y. Li

In order to obtain a more suitable separation medium for fine coal, in this paper a pulsed fluidised bed was used to measure the pressure fluctuation, density characteristics, bubble diameter and rising velocity of Geldart A and B particles in the bed by controlling the pulsation frequency and gas velocity, in order to study the fluidisation effect and two-phase distribution of the bed. The results indicated that with the increase of pulsation frequency, the breakthrough point on the fluidisation characteristic curve caused by particle adhesion disappeared, and there was an optimal frequency, which made the minimum fluidisation velocity of particles reach the minimum. In addition, the bubble rising velocity was also simulated. The relationship between them was established using a model, and the error was within 5%. This provides an effective way to predict the bubble velocity, study the distribution of bubble phase, and improve the stability of bed density. Keywords：Frequency, flow velocity, pressure fluctuation, bed density, bubble

Jan 1, 2020

By R. Asamoah, P. Forson, S. Xu, W. Skinner, M. Zanin

In most auriferous hydrothermal deposits, gold is preferentially associated with pyrite and arsenopyrite minerals, with higher economic gold values noted for the latter and arsenian pyrite minerals. In this paper, surface (Cryo-XPS) and solution (EDTA extraction) analysis were used to characterise pyrite and arsenopyrite minerals under different aqueous conditions involving electrokinetic study and collector interactions to better understand ways of improving the separation of pyrite and arsenopyrite. The evidence showed higher surface oxidation at solution pulp pH values in the range of 4-11 for arsenopyrite relative to pyrite. The observed highest ratio of pyrite to arsenopyrite selectivity was 1.7 at collector concentration of 50 g/t and decreased with an increase in collector concentration. Keywords: EDTA extractable iron, selectivity index, differential flotation, grade engineering

Jan 1, 2020