Search Documents

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council. Although the worldwide readership of the Journal results in a preference for papers in English, the Council treats papers in Afrikaans on an equal basis, but, to meet the needs of the majority of readers, an English summary of some 5OO to 750 words should be provided.

Jan 1, 1984

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By B. Rezai, Z. Pourkarimi, M. Noaparast, S. Chehreh Chelgani

Nanobubbles (NBs) flotation separation can be an indicator for improving the efficiency of fine particles through the conventional process. Since flotation reagents such as frothers can reduce bubble size, they can potentially be used for the generation of NBs and develop a selective NB flotation separation. This study explored the flotation separation of fine phosphate particles from their associated minerals in the presence of NBs, which were generated by using a phosphate flotation reagent (Flo-YS: collector-frother). The results of flotation tests showed that in the presence of NBs, the flotation efficiency was significantly improved. However, in the presence of NBs, surface chemistry analyses (Fourier Transform Infrared Spectroscopy and High-Performance Liquid Chromatography) illustrated that the collector adsorption on the surface of phosphate particles decreased. A comparison between outcomes of various phosphate flotation conditions indicated that increasing the flotation efficiency in the presence of NBs may be due to the aggregation of fine particles by the generated NBs, and also selective adsorption of NBs (hydrophobisation) on the surface of particles. In other words, generating NBs by selective collectors may increase efficiency and decrease the collector consumption of a flotation process. Keywords: Phosphate, selective separation, fine particles, collector-frother, efficiency, mechanical flotation cell

Jan 1, 2020

By T. G. Pedro, Q. Gonzalo, R. E. Roberto

Anionic surfactants, such as oleic acid and sodium oleate (OLE), and cationic surfactants, such as dodecyl amine-hydrochloride (DDA), are used as flotation collectors of spodumene. However, recovery is poor even if activating ions are used because gangue minerals are also activated. Some reports demonstrate that OLE/DDA mixtures act as a selective collector to enhance spodumene recovery. From mostly macroscopic tests, it has been argued that anionic OLE and cationic DDA form electroneutral complexes, which are adsorbed on the mineral surface through chemisorption; however, no molecular evidence has been presented. Therefore, the adsorption mechanisms of the collector mixtures remain mostly unknown. It seems necessary to first study the behaviour of these surfactants confined in salt solutions, to determine auto-associations when they are pure and cross-associations when mixed, the transition from monomers to micelles, and the structure of the micelles and the effects of pH, temperature and concentration. In this paper, ab initio calculations are first used to determine the surface charge distribution of OLE and DDA separately. Then molecular dynamics simulations are used to determine the conformation, aggregation, and diffusion of these pure and mixed surfactants in freshwater and saltwater with the ionic strength of seawater in a pH range. In particular, it is interesting to determine the various associations that result in mixtures of both surfactants and the impact of alkali and alkaline earth metal cations on the structures formedp. Cations influence the order of the structure and orientation of water dipoles, reducing the mobility of water, ions, and surfactant molecules. This knowledge is critical to improve the molecular understanding of the adsorption mechanisms on minerals. Keywords: Computer simulation, molecular dynamics, flotation, collectors, saltwater

Jan 1, 2020

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By S. T. L. Harrison, J. R. Amaral Filho, M. Smart, J. Broadhurst, J. Weiler

Technosol production from mine waste, following amendment with additional organic residues, to provide healthy and functional topsoil is an advantageous alternative to the long-term dump disposal of mine waste. Minimising the legacy of mine waste and supplying soil for mine site rehabilitation contributes towards more sustainable mining practices. Following the creation of the physicochemical structure of the soil from appropriate mixtures of coal waste with low sulfur content, physical ameliorants and nutrient sources, the inoculation of Technosols with active microbial suspensions may accelerate the decomposition of organic matter present and ensure nutrient availability for plant growth through active nutrient cycling, particularly of nitrogen, sulfur and phosphorous. In this paper, South African ultrafine coal waste was used as the main mineral matrix, and malt residue was used as source of organic matter and nutrients. In order to evaluate the effects of Technosol inoculation, five microbial treatments were used, including the addition of: commercial grade efficient microorganisms (EM Prosoil), anaerobic digested sludge supernatant from treating brewery waste, and ‘tea’ extracts prepared from compost, vermicompost and soil native to the mining area. Growth experiments were carried out using Eragrostis teff, commonly known as teff, a grass typically used for the rehabilitation of mined areas in South Africa. Preliminary results showed that Technosols inoculated with microorganisms performed better in terms of nutrient availability and plant growth. Varied performance was observed as a function of the microbial inoculation applied. This suggests that the inoculation of Technosols with appropriate microorganisms may be recommended to accelerate nutrient availability assisting plant growth during the initial establishing of the Technosols. Technosols continue to show promise as an alternative to both mine waste disposal and the burrowing of topsoils for mine rehabilitation. Keywords: Fabricated soil, mine waste, coal discards, malt residue, nutrient availability, soil microbiology, plant growth

Jan 1, 2020

By C. I. Kim, I. C. Paek, I. K. Tae, P. J. Thak, U. C. Han, K. S. Jong

This paper analyses the energy consumption according to the type of dump scroll track during skip discharging in an inclined shaft hoist for an open pit mine. For the purpose of the project, it was necessary to set up an equation for a geometrical locus of a skip dump scroll track, and from the need for technical engineering and study purposes, to derive equations for two track types by using cam design theory (cosine track and linear accretion track). Skip discharging is analysed using discrete element method software, and dynamic simulation of its run is performed using Visual Nastran software. The energy consumption during skip discharging can be calculated from the rope tension obtained by dynamic simulation, and graphs obtained from the simulated results using discrete element method and Visual Nastran software. From this, the study demonstrates that the energy consumption at the cosine track is always lower than that at the linear accretion track, without regard to the property change of a payload depending on grain size distribution.

May 8, 2026

By D. K. Weatherley, T. P. Oladele, L. B. Bbosa

Comminution is a critical stage of mineral processing which aims to reduce the size of ore particles through breakage, consequently increasing the likelihood of liberation of valuable minerals. Several factors, such as pre-existing cracks, mineralogical composition and particle size, are known to affect ore breakage behaviour. While investigating the contributing role of each factor is essential to improve understanding of breakage, isolating individual factors by experiment is typically impractical. Numerical techniques such as the Bonded Particle Model-Discrete Element Method (BPM-DEM) have been developed as a means of studying closely controlled breakage conditions. This study evaluates this technique in modelling the effect of pre-existing cracks breakage behaviour for synthetic ore specimens during impact breakage in a short impact load cell (SILC). Synthetic ore was modelled as a collection of discrete entities connected by brittle-elastic beams. Model parameters were calibrated against macroscopic material properties of a conventional homogenous synthetic ore. The extent of pre-existing cracks within specimens was prescribed by varying discontinuities between the connecting entities. An approach with the insertion of seed points was used to model the mineralogy of the specimens. Results showed that pre-existing cracks resulted in a decrease in the fracture force as the crack density increased. Additionally, the irregularity of fracture patterns within rock specimens after impact became more apparent as the crack density increased. The findings were used to emphasise some of the attributable causes of the variation observed between ore hardness characterisation tests and in situ ore behaviour. Keywords: Element Method; Bonded Particle Model, synthetic rock sample; rock fracture, preexisting cracks

Jan 1, 2020

By T. Song, X. Wang, X. O. Xia, X. J. Luo, B. Chen

Interparticle breakage is the main crushing mode of an inertia cone crusher according to its working principle and feeding condition. In this paper the breakage behaviour of an inertia cone crusher is investigated, based on energy controlled compression combined with the vibration theory, rather than geometry controlled compression (form conditioned) which plays a major role in conventional eccentric cone crushers. The effect of feeding and operating conditions on breakage behaviour was described quantitatively from the perspective of energy consumption and product size distribution. The influence of feeding conditions, discharge size settings and vibration exciter speeds on the crushing process and product quality has been studied according to the results of laboratory crushing experiments. The results of the experiments show that the particle size of broken products becomes finer with the decrease of a discharge gap within the gap range selected by the experiment. The product size increases significantly when the gap approaches the upper limit of 6 mm. The variation of eccentric speed has a more prominent effect on reducing the product size compared with the change of discharge gap. The change in product size is not apparent when the eccentric speed rises to a certain level. The throughput of an inertia cone crusher is sensitive to the change of discharge gap, which increases linearly with the discharge gap and decreases with the eccentric speed. The change of feeding conditions has little influence on the crusher throughput. Keywords: Inertia cone crusher, interparticle breakage, energy consumption, product size distribution

Jan 1, 2020

By P. R. Jochens, D. D. Howat, M. S. Rennie

The slags arising from ferrochromium plants were simulated by additions of CaO and Fe2O3 (6 per cent each), Cr2O3 (7 and 12 per cent), and Fe2O3 and Cr2O3 together (6 and 12 per cent respectively) to slags in the MgO-Al2O3-SiO2 system. These additions were made to slags having an SiO2 content of 45 per cent and an MgO-to-Al2O3 ratio of 4 to 3 or 3 to 4. The effect of these oxide additions on the liquidus temperatures, electrical conductivities, and viscosities was determined. The additions of CaO and Fe2O3, although having little effect on liquidus temperatures, decreased viscosity and increased electrical conductivity. The addition of Cr2O3 raised the liquidus temperatures considerably, and tended to decrease viscosity in the temperature range 1 700 to 1 800°C and to increase electrical conductivity.

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020

By V. V. Getman, V. A. Chanturiya, T. N. Matveeva

Most of the Au and PGM ores in Russia are characterised by a thin mineral impregnation of noble metals in sulfide minerals, and a large variety of mineral forms that lead to high loss of precious metals with fine fractions during flotation. In modern flotation technology, the rational choice of reagents is one of the main trends for selective separation of minerals and effective metals recovery. New data on the selectivity of the thermo-sensitive polymer with specific functional groups (TMPPh) as a flocculant and collector of Au and Pt fine fractions are available. The selective modified collector (DEDTCm) for the recovery of Au and Pt from complex ores is discussed in this paper. Scanning electronic microscopy (SEAM), laser SIM and AFM microscopy, UV and IR spectroscopy were applied to study the adsorbed layer of new reagents on the mineral surface. Flotation tests of TMPPh on the gold-bearing ore of the Olimpiada deposit showed an increase in Au extraction and Au content in the concentrate of the rougher flotation. Using a combination of reagents TMPPh and ButX, the quality of the Au and Pt concentrates increased in 1.7 time with an increase in recovery up to 15 % compared with the traditional reagent mode. Testing of TMPPh polymers in flotation of Pt-Cu-Ni ore at Norilsk Nickel has shown the ability to obtain a concentrate with a higher Pt content. Recovery of platinum is 17% higher than recovery in an experiment without polymer. Application of DEDTCm helped to achieve higher technological parameters in flotation of lowgrade Rt-Cu-Ni ore. Compared to the basic mode Pt recovery was plus 13%, Pd recovery was plus 9% and the content of precious metals in the rougher flotation concentrate increased in 2,5 - 4 times. The studies have been supported by Grants of the President of RF “Scientific School of Academician V.A. Chanturiya” NSh-220.2012.5, NSh-748.2014.5. Keywords: Au and Pt complex ores, flotation, flocculation, thermo-sensitive polymer TMPPh, modified collector

Jan 1, 2020

By X. Zhang, Z. T. Yuan, C. Zhang, H. M. Zheng, X. M. Wang, L. X. Li, N. Li

In metal mines, comminution is commonly used to liberate minerals for subsequent mineral concentration processes, such as flotation, magnetic separation and gravity separation. However, ores are aggregates of valuable minerals and their disseminated gangue minerals, and these minerals exhibit diverse comminution behaviours. In carbonate-bearing iron ores, hematite, siderite, and quartz are the predominant minerals, of which hematite is the objective recoverable mineral. In this regard, the present study aimed to identify the imperfections in siderite minerals by X-ray computed tomography (XCT), and thus quantitatively characterise their size and shape in terms of Feret diameter and aspect ratio, as well as other parameters. XCT images indicated the protogenetic ubiquity of pores <5 μm in diameter and cracks of 7-8 μm inside siderite particles. In the ground product of artificially mixed siderite and hematite, siderite particles were smaller than hematite particles. Siderite particles had a larger surface area and greater surface roughness than hematite particles of the same volume, which was attributable to the intrinsic holes and cracks in siderite particles. This study provides an insight into the relationship between the inherent imperfections of minerals and their comminution properties. Keywords: Siderite; X-ray computed tomography; particle imperfections; grinding behaviour; sliming

Jan 1, 2020

By S. Purushotham, Y. R. Murthy, M. Narasimha, S. K. Tripathy, M. Kumar

Spiral concentrators are gravity-based separators widely used to beneficiate coal, heavy minerals and beach sand. It consists of a helicoid trough that spirals downward in the helical configuration around an axial column. The particle segregation takes place based on size and density under the influence of gravity as the particles spiral down within the thin water layer. In the last century, most design modifications of this equipment were based on trial and error based lab-scale experimentations and empirical approach. The use of Computational Fluid Dynamics (CFD) has gained interest in the past two decades to understand the underlying flow physics in the spiral concentrators. In this paper, we used CFD to model the fluid flow and investigate the particle segregation inside a conventional LD9 spiral concentrator. Firstly, the Volume of Fluid model was used to resolve the liquid-air interface. The liquid depth and flow field predictions for varying flowrates were validated against the experimental literature data. One-way coupled VOF-LPT model was then used to describe the particle dynamics in the spiral flow field assuming dilute particulate flow. Moderate dense particulate flow (20 vol.%) was then modelled using the Algebraic Slip Mixture (ASM) model. Four particle-phases representing particles of different sizes of dual-density were simulated, and the component particle segregation was analysed. Keywords: Spiral concentrator, two-phase flow, multiphase, discrete phase model, ASM model

Jan 1, 2020

By M. Klapwijk

Ancient Metallurgy - In addition to the preceding three papers, the following three contributions were received for publication 1. An analysis of Bantu-made iron implements from the Letaba district M. KLAPWIJK INTRODUCTION It has often been stated that it is hardly possible in South Africa to classify Bantumade iron hoes according to their places of origin and manufacture. It is well known that these hoes were used for barter, and as currency in the purchase of livestock or the payment of lobolo, although reports of the value of the hoes differ widely. The difficulty in their classification has arisen from their distribution over a very wide area.

Jan 1, 1974

By X. Cao, R. Wang, H. Han, Y. Hu, Z. Wei, W. Sun, H. Tang, J. Wang

Flotation reagents play a vital role in mineral flotation. In the past century, most studies focused on the modification of anion or cation collectors and the synergistic effect of mixed collectors, which have contributed to research. In this study, we reviewed brand-new reagents, metal-organic/inorganic complexes, with the functional group of metal ion, which are totally different from the traditional anion or cation collector and show absolute specificity for some minerals. For example, Pb-BHA complex collector was developed to realise the atmospheric flotation of scheelite due to the absolute specificity for calcium minerals. Calcium oleate collector was found to be the effective species in the flotation of calcium minerals, and has been employed to selectively separate fluorite from calcite. Selective adsorption of Al-Na2SiO3 polymer on calcite surfaces proved the self-assembly of H2SiO3 polymer using Al3+ had stronger selectively adsorption ability than Na2SiO3. Also that Fe3+-starch complex was a better depressant for iron minerals than caustic starch and contributed to a more efficient reverse flotation. In conclusion, metal ions are good templates for molecular assembly and can be used to control the structure of metal complexes and exhibit special properties, which provide possibilities for the design of new flotation agents. Keywords: Metal-organic/inorganic; flotation; collector; depressant

Jan 1, 2020

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By Y. Tanaka, H. Miki, Y. Aoki, H. Okamoto, G. P. W. Suyantar, T. Hirajima

Due to environmental limitations and the scarcity of freshwater, flotation using seawater or desalinated seawater as process water becomes more common for mining operations. On the other hand, seawater has been reported to affect the flotation behavior of sulfide minerals. Few reports are available on influence of pyrite depression, recycled seawater and lime consumption on flotation by using seawater. In this study, the flotation tests were performed using ore sample to investigate the effect of pH with seawater and process water used in plant on the flotation behavior in a laboratory-scale flotation cell and a pilot plant-scale. The results of laboratory scale flotation indicated that copper and molybdenum flotation kinetics decreased with increasing pH. Furthermore, the iron (mainly pyrite) recovery decreased with increasing pH. The pilot plant-scale flotation test showed that water with a higher concentration of magnesium and calcium (plant processes water) consumed a higher amount of lime. Because of low lime consumption and high copper and molybdenum recovery and grade, pH 8 is suitable compared with pH 8.5 for flotation. Keywords: seawater, process water, copper-molybdenum rougher flotation, pH, pilot test

Jan 1, 2020

The Institute has concluded an agreement with the Chamber of Mines whereby the Chamber Librarian maintains a section in the Library for the Institute. Surface effects of underground mining South Africa is blessed with vast mineral resources. It is essential to exploit those reserves if the country is to remain economically viable. Surface-mining equipment The Goldfields Mining Expo &apos;86 is to be held in Kalgoorlie, Western Australia, from 30th October to 1st November, 1986, in conjunction with the Annual Conference of the Western Australian School of Mines. Mintek reports Report M142D Characteristics of gold and pyrite flotation at the Chemwes plant. (1st issued May 1984.) Report M159D Beneficiation tests on andalusite ore from the Marico district. (1st issued Aug. 1984.) Report M164D The recovery of tungsten from South African low-grade schee/ite concentrates. (1st issued Sep. 1984.)

Jan 1, 1986

By F. S. Hoseinian, D. Deglon, L. leal Filho, M. Safari, T. C. Souza Pinto

This paper investigates the effect of chemical and physical operational parameters on the reverse flotation of Timbopeba itabirite iron ore in a pilot-scale pneumatic flotation cell. Operational parameters include collector and depressant dosages, feed rate, superficial gas velocity and solids concentration. Results show that increasing collector dosage results in an increase in quartz recovery, particularly for the coarser quartz where recovery increases by nearly 30%. Increasing depressant dosage results in a decrease in both quartz recovery and hematite loss, for the coarser hematite particles. Increasing the feed rate has no effect on quartz recovery or hematite loss, suggesting that the pneumatic flotation cell is not residence time constrained. Increasing the superficial gas velocity results in an increase in quartz recovery to an optimum at a Jg of around 0.6 cm/s after which it decreases significantly, particularly for the coarser particles where recovery decreases by as much as 50%. Decreasing the solids concentration does not affect quartz recovery but results in significant decreases in hematite loss. Here, fine and coarse hematite loss decreases from around 25% to 12% and 10% to 2% respectively. Superficial gas velocity and solids concentration are operating parameters which have the largest effect on the flotation performance of the pneumatic flotation cell. Results suggest that this flotation cell should be operated at relatively low superficial gas velocities and solids concentrations. However, these are pilot-scale findings and would need to be tested at an industrial-scale where different operating conditions may be optimal. Keywords: Operational parameters, reverse froth flotation; entrainment; iron ore

Jan 1, 2020