Search Documents

By N. A. Smith, R. J. Fowell, J. L. Hislam

Abstract: Data are presented from two sites in southeast England, where problems were encountered in tunnelling through ground containing flint. In response to the difficulties, substantial laboratory testing programmes were initiated to determine the strength of the flints.It is shown that the strength varies very considerably, even within a single flint particle and that the practice of estimating unconfined compressive strength by a single multiplier applied to the point load strength index (Is(50)) may give misleading results. The preparation of UCS specimens for testing was found to be very difficult and it is recommended that tunnel machine capacity is assessed relative to Is(50). Résumé: Des données sont presentées sur deux sites dans le sud-ouest de l’Angleterre,où le perçage d’un tunnel dans un sol contenant du silex a posé des problémes. En consequences de ces difficultés, des programmes substatiels de recherché en laboratoire ont été initiés afin de déterminer la resistance des silex. Il est demontré que la resistance varie considérablement, même au sein d’une particule de silex, et que la pratique de estimation de la résistance en compression non confinée, (UCS) par le biais d’un simple coefficient appliqué au ‘point load strength index (Is50)’ pourrait donner des resultants trompeurs. La préparation de specimens UCS destinés aux tests s’est avérée trés difficile et il est recommandé que la capacité de la machine de perçage de tunnels soit calculée relativement au Is50. Zusammenfassung: Daten von zwei Standorten in Südosten von England, wo Probleme beim Tunnelbau durch feuersteinhaltigen Grund antraffen, sind angegeben. Wegen diesen Schwierigkeiten wurden Laboratoriumsforschungsprogramme eingeleitet, um die Festigkeit von Feuersteinen zu bestimmen. Es wurde gefunden, dass die Festigkeit sehr unterschiedlich war, selbst bei einzelnen Feuersteinstücken, und dass die Praxis, die unbegrenzte Kompressionsfestigkeit (uKf) auf Grund eines einzigen Multiplikationsfaktors vom Punktladefestigkeitsindex (Is50) abzuschätzen, zu irreführenden Resultaten führt. Die Vorbereitung der uKf Prüfstücke war sehr schwierig und es wird vorgeschlagen, dass die Kapazität der Tunnelbaumaschine in Abhang der Is50 bestimmt wird.

Jan 1, 2003

By A. Fouchee, N. Naudé, K. Schommarz

"This article presents laboratory test work conducted on an African haematite ore to determine the influence of the flotation pulp pH on the final iron grade and recovery. Results show that a combination of an isodecyl ether propylene amine/amino acetate and 1,3-propanediamine, N-(3-(C10-C16-alkyloxy)propyl)-derivatives collector is suitable for separating haematite from quartz. Higher iron grades were obtained at pH levels between neutral and pH 9. This underlines the importance of the surface charge effect of the ore on its flotation characteristics. The results serve as good baseline conditions for further optimization. IntroductionBeneficiation of iron ore by flotation is widely used in Brazil, India and China. In Africa, however, this practice is not yet commercially developed.The aim of this test work is to serve as a starting point by establishing suitable pH conditions for the development of a practically implementable reagent suite, which will then be included in a larger beneficiation circuit for producing high-grade iron ore sinter feed.In the literature, African iron ore types are graded as low-grade (60.0–62.9% Fe; 8.6– 12.5% SiO2 and insolubles), high-grade (66.0– 69.9% Fe; 0.8–4.5% SiO2 and insolubles), and meduim-grade as the remaining portion (Astrup et al., 1998). The low-grade ore used in this work contains less than 60% Fe.For Brazilian ores consisting of a combination of haematite and quartz, it is common to use corn starch as a depressant and ether amine blends as collectors with additional frothing characteristic (Araujo et al., 2005). Work by Turrer and Peres (2010) shows the possibility of using other depressants successfully as well.The main mechanism of the reverse flotation of quartz from iron ore is based on the electrostatic theory of flotation. This is due to the strong pH dependence of the zeta potential of the mineral edge planes on silicate particles (Fuerstenau and Pradip. 2005)."

Jan 1, 2016

By M. Gao

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By C. P. Naudé

Mechel, a large, integrated steel, stainless steel, and ferroalloy producer in Russia is committed to upgrading its facilities to world class pyrometallurgical process and environmental practice. Yuzhural Nickel currently uses shaft furnaces to produce a matte containing iron, nickel and traces of cobalt. This rather old technology is thermally inefficient and is characterized by high operating costs. Mechel has investigated suitable equipment and processes to upgrade the plant, and awarded a contract for the construction of a 12 MW DC smelter, located near the town of Orsk, to Bateman Engineering Projects in June 2008. The selection of DC furnace technology for laterite smelting can be considered as a strategic highlight for the pyrometallurgical treatment of low-grade lateritic ores, and could be the first industrial-scale implementation of this technology. This project has been designed to achieve multiple goals including the demonstration of the process and associated equipment technology at commercial scale, to confirm the scale-up design parameters of the forthcoming 2 x90 MW, twin electrode DC furnaces, and to prove the environmental emission superiority of closed furnaces. It also provides a valuable operator training platform. This paper deals with the process design, key technology building blocks and design features which have been incorporated to produce a pyrometallurgical vessel capable of (i) resisting slag superheat and chemical aggressiveness, (ii) process fine material without pre-agglomeration, (iii) achieve high nickel recoveries and(iv) being tolerant to the variations in chemical composition of laterite ore. The approach to increasing campaign lives between partial and complete rebuilds, through the use of composite furnace module (CFM) technology originally developed and patented by the University of Melbourne, is also followed in more detail. Unfortunately, results from hot commissioning and lessons learned from initial operation are not available because the project completion has been delayed due to the worldwide downturn in demand for commodities. Keywords DC furnace, ferronickel laterite smelting, corrosive slag, coppercooler technology.

Jan 1, 2010

By G. R. Lane

My opportunity to serve as President of the prestigious Southern African Institute of Mining and Metallurgy (SAIMM) was made possible by an Anglo American scholarship 39 years ago—a pivotal moment that set me on a career path spanning various roles and start-up ventures in the mining industry. Over the past decade, I have been privileged to broaden my experience by consulting across diverse industries globally. This exposure revealed something profound: what I had previously considered mining-specific challenges are, in fact, universal across many sectors. At its core, a mining operation is a complex system of interconnected activities—from exploration through mining operations like drill and blast, load and haul, to beneficiation, and outbound logistics. My cross-industry work has clearly shown that diverse sectors, such as chocolate manufacturing, tissue paper production, toilet paper converting facilities, labgrown diamonds, or high-tech equipment lifecycle management, all rely on value streams of interconnected activities to transform products. The objective is to maximise throughput while effectively managing performance variability. The primary difference lies solely in the specific technical expertise required for each industry, such as chemical, mining, processing, or metallurgical engineering. Across all these industries, I have observed a consistent pattern, that is, performance is primarily driven by individual efforts, where people react and work diligently as situations unfold in real-time. General managers and their teams often operate tactically, focusing on explaining yesterday’s poor performance rather than proactively setting up operations for success. This often resembles an ‘‘under-7s soccer match’’, with everyone chasing the ball. The common response to issues is to add more ad hoc meetings. This effort-driven organisational behaviour persists regardless of whether operations are greenfield digital manufacturing facilities, advanced digital mines with advanced process control, or operations run on paper and Excel spreadsheets for data acquisition. Paradoxically, more real-time data can lead to increased data noise, greater indecision, and sometimes, lower performance. Despite value streams often operating significantly below capacity, organisations continue to invest heavily in additional equipment or in ‘‘glossy brochure promises’’ of Industry 4.0 digital technology and real-time data solutions, which frequently fail to deliver value. This leads to a critical question: Have we underinvested in our most valuable resource— people? Even Tesla faced this challenge with their underperforming fully automated Model X facility. We must shift our focus to designing the ecosystem, or operating model, of our organisations. This extends beyond the traditional triad of people, process, and technology, and moves beyond simplistic views of change management. Artificial Intelligence (AI) has the potential to add significant value, but it also introduces another layer of complexity into designing the organisation of the future. My full presidential address below at the SAIMM AGM discussed the symptoms of an effort-driven organisation and covered the fundamental building blocks and requirements of an operating model, including recommendations on implementing a people-centric approach.

Oct 2, 2025

The statistical methods described in the previous chapter permit the estimation of the average value p of a deposit, and the calculation of confidence limits for this value. They are based on the assumption of independence of sample values. As soon as a reasonable number of samples has been obtained from a deposit, local valuation, or estimation of blocks of ore within the mineral deposit, becomes necessary. The assumption of independence of values must then be rejected. Local valuation is possible only if there is a relationship between the value of a sample and the value of the surrounding ore, provided this relationship is a function of the position of the sample with respect to the blocks of ore to be valued. Whichever method is used for the valuation of a block of ore, the following assumptions are always made: ? The values of samples located near or inside the block are related to the value of the block. ? The values of the samples located closest to the block are most closely related to the value of the block. These assumptions will hold true only if the following assumption can also be made: ? There exists a relationship between sample values which is a function of the distance between samples. We are saying that the value x (z) of a sample centred at a point z has properties which are functions of this point. A certain spatial structure exists in the sample distribution. We are therefore dealing with a regionalized phenomenon, and we must treat x (z) as a regionalized variable. This can be done statistically by means of a model chosen to represent the spatial structure of the phenomenon. We shall see that the relationship between block values and sample values can be deduced from the relationship between sample values, and all local valuation problems can be solved using the statistical model obtained from the analysis of the sample values. It is important to realize that this statistical model is obtained by analysing the properties of known sample values, and will be used for the estimation of unknown block values. Such a statistical inference is valid only if the model developed represents the properties of both the sampled section of the ore body and the section to be valued: some stationarity conditions must be satisfied, and the model with the least restrictive conditions is preferred. In the following chapters, the most important models used in spatial geostatistics are presented. The models which can be used when there is no significant drift (trends) in values are described in Chapters 3-1 1. These models can also be used to solve some specific valuation problems when a linear drift is present. A general study of the more difficult problem of analysis of an ore body whose values present a drift is described in Chapter 12. Note that the area considered for local valuation of a block of ore is often small enough for any drift which might be present to be ignored.

Jan 1, 1978

Notices EIGHTH WORLD MINING CONGRESS The Eighth World Mining Congress will be held in Lima, Peru, from 3rd to 8th November, 1974. The theme of the Congress is 'Prognosis of mining development up to the year 2000', with the following subthemes: INF ACON 74 Readers are reminded of the International Ferro-alloys Congress being organized by the National Institute for Metallurgy, in conjunction with the Ferro Alloy Producers' Association of South Africa and the South African Institute of Mining and Metallurgy.

By H. G. M. Rose

Contribution to the above paper by H. G. M. Rose* (Fellow) INTRODUCTION Dr Lawrence is to be congratulated on his most interesting and instructive paper, particularly on his suggestion for a model to increase mining productivity through improved management performance. In view of an experiment initiated in one Union Corporation mine (Mine A) and later extended to a second mine (Mine B), it might be of interest to review the many human factors involved and the initial productivity results achieved.

Jan 7, 1974

By A. N. Brown

The Hendrik van der Bijl Memorial Lecture is arranged annually under the auspices of the Pretoria Engineers Liaison Committee. This is a multidisciplinary Committee with representatives from eleven societies and associations, and serves the interests of engineers resident in the Pretoria area. Coal preparation The Japanese Organizing Committee of the 11th International Coal Preparation Congress is now busy making the necessary arrangements for the Congress, which is to be held in Tokyo from 22nd to 26th October, 1990.

Jan 1, 1989

Proceedings of a General Meeting held at the Witbank Golf Club at 19h30 on 3rd November, 1977 Geomechanics colloquy The 27th Geomechanics Colloquy is to be held on 12th and 13th October, 1978, in the Salzburg Congress Hall. The themes of the four half-day sessions will be as follows: Conference on pneumoconiosis The Vth International Conference on Pneumoconiosis is to be held in Caracas (Venezuela) from 29th October to 3rd November, 1978.

Jan 1, 1978

By D. I. Hoyer, M. F. Dawson

The results obtained from the operation of a batch centrifugal ball mill are reported, together with the development of a model for the behaviour of a particle in free flight within the mill, and the introduction of a cumulative breakage rate function. Schumann and Rosin-Rammler plots show the change in particle-size distribution with time at various configurations of the mill. Graphs showing the rate of production of fines and the rate of breakage of coarse particles are included.

Jan 1, 1982

By H. E. James

GOLD 100, the most comprehensive international conference on gold ever held anywhere in the world, took place in Johannesburg from 14th to 18th September, 1986. The Conference was followed by a series of one day visits and an extended technical tour. The Conference was organized jointly by the Council for Mineral Technology (Mintek), the Chamber of Mines of South Africa, the School of Business Leadership of the University of South Africa, and The South African Institute of Mining and Metallurgy.

Jan 1, 1986

By D. A. Viljoen

An account is given of the development of man's interest in the recovery and working of minerals from Palaeolithic times to the present. This is followed by a discussion of future production trends for the more important minerals, and of likely technological developments in the recovery of various minerals. The crucial importance of energy minerals is stressed, as are several other factors of significance to a flourishing minerals industry: manpower, education, financial climate, Industrial health and safety, and preservation of the environment.

Jan 1, 1979

By D. Yu Pleev, V. G. Krivolapov

Mines of Southern Kuzbass working out, basically, coal formations of flat seams. Seams, as a rule, are inclined to self-ignition. Detection at early stages of the centers of endogenous underground fires has great value for safe conducting mountain works. One of methods of detection of an early stage of underground fires in the worked out space is the method of superficial radon survey. In the report the method is de-scribed and examples of superficial radon survey on concrete layers are given.

Jan 1, 2003

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By F. K. Mulenga, M. Lusambo

"Geometallurgical models are a strategic tool used primarily in planning, diagnosis, and process optimisation. This paper discusses the development of a predictive model for flotation recovery at Kansanshi concentrator in Zambia as a function of key operational parameters. Daily data for milling and flotation from the circuit processing the copper sulphide ore was analysed. This data, recorded over a period of one year of production, was collected from diverse sensors measuring semi-autogenous milling and flotation parameters. Statistical analysis showed that copper head grade, acid-insoluble, and acid-soluble copper, SAG mill throughput, ball mill load, and tonnage of feed material to the SAG mill in the -125 +63 mm size fraction contributed to the prediction power of the proposed empirical model by as much as 90%. Finally, a proposal was made for the development of a simulation model under MODSIM®, a flexible tool for mineral processing applications. This was to test the limitations of the empirical model for future refinement. IntroductionKansanshi is the largest copper mine in Africa and the world’s eighth largest copper producer, with a total of 253 272 t of copper produced in 2016 (Newall, 2017). It is located approximately 10 km north of Solwezi, the capital and administrative headquarters of the North Western Province, Republic of Zambia. The ore deposit consists predominantly of chalcopyrite and malachite with variable amounts of chalcocite, bornite, chrysocolla, and azurite. Because of the varying proportions of sulphide and oxide copper minerals, the ore is classified into three distinct categories: sulphide, mixed, and oxide ores. As such, three separate processing circuits are used to mill the ore down to a standard targeted grind size of 80% passing 150 µm before froth flotation and leaching.A lot of research and development has been done to improve the performance of the sulphide ore circuit at Kansanshi. Despite the research efforts and subsequent operation, the sulphide ore circuit did not attain the target recovery and grade for 2016, primarily because of the complexity of the orebody.The constant drive to achieve the set production target of recovery and concentration grade after froth flotation motivated the development of a tool for the prediction of recovery. The anticipated benefit is not only to enable the plant to apply corrective actions when needed, but also to make a tool available for the quick assessment of the plant performance of the. For that purpose, data spanning June 2016 to May 2017 was analysed, cleaned up and curvefitted to an empirical model. In doing so, key parameters were determined and calibrated to represent the behaviour of the plant."

Nov 1, 2018

"Chairman: Mr W. S. GALLAGHERRapporteur: Professor A. M. STARFIELDPapers:Long-term mine production scheduling by G. C. S. BurneAn application of linear programming to investment analysis by A. ErlandssonOptimizing medium-term operational plans for a group of copper mines by M. Splaine, D. C. Atkinson, W. Davison and L. SmithThe simulation of underground stoping and transport operations in gold mining by F. H. Touwen and N. C. JoughinProduction planning is a subject that lies at the interface between the computing centre and mine management. Discus¬sion during this session was thus largely concerned, directly or indirectly, with communication between computing and mining personnel, and as such was relevant to the symposium as a whole.Mr A. Weiss set the tone of this discussion by referring to `user-orientated systems'. He congratulated Mr Burne in this regard, pointing out that his long-term production scheduling program, as a computer system, was similar in approach to the manual system it replaced, and was therefore easily understood by planning engineers. He asked whether the schedule engineer had his 'hands on' the system, to which Mr Burne replied that the engineer did in fact spend several days running alternative schemes through the computer. Mr Weiss commented on the advantage of having terminals on site for this sort of engineer-computer interaction. He also commented on the flexibility of Mr Burne's approach to scheduling and how preferable this was to a one-step optimization package. This was brought home by a question from Mr H. D. Small: Mr Burne's program sometimes found it necessary to temporarily halt an advancing face, and he asked whether the logic of the program could be altered to avoid this (e.g. by suitably slowing down the rate of face advance). Mr Burne replied that it was in fact easier for the planning engineer to sort this problem out manually. The way in which the computer results were presented made it particularly simple for the production engineer to see how to avoid or remedy a stopped face.On the technical side, both Mr Weiss and Mr H. M. Wells questioned Mr Burne on the handling of grade control by his program. From answers by Mr Burne and his colleague Mr K. H. Thomson it emerged that a spot-check on grade every now and then was all that was necessary at Mufulira, and that the idea of actual grade control was more a question of short-term than of long-term planning."

Jan 1, 2014

On 23rd October, 1969, 54 members of the Institute set out at an early hour from Rand Airport in two chartered Dakota aircraft for a visit to the Hendrik Verwoerd Dam site. The weather was at the start rather unpromising but after passing Bloemfontein the overcast cleared and it turned into a glorious day for a most memorable visit. The Institute is indebted to U.C-Dumez-Borie Dams Limited, the main civil engineering contractors, and Mr J. D. McNamara their executive manager, for the very excellent arrangements made for this excursion. From the time the aircraft landed till a slightly belated departure the organisation of the extensive tours arranged for the parties was quite outstanding and a matter for congratulation to all concerned. At each of the many places visited there was a senior official to give an authoritative and comprehensive description of the work under his control. In addition the guides on the buses, loaned by the Department of Water Affairs, kept up an interesting running commentary throughout the day. A further much appreciated facet was the introduction of many of the experts on the site and a brief talk by each after an excellent lunch served at the recreation club. Each visitor also received a brochure with a progress report and a detailed site plan, with various sections highlighted in colour, and obviously prepared at the cost of much time and effort. The visit included tours of the large dolerite quarry, where some 150 000 tons of rock are removed each month, the 42 in. gyratory primary crusher, the secondary crushing and screening plant, the rod mill plant for sand production, and the automated blending and concrete batching plant. The transport of mixed concrete by 'silobuses' to the 6 cu. yd buckets of four Blondin cableways, two of which are radially movable and two with buffing towers, and the placing of the concrete in the huge blocks of the wall was watched from a vantage point. The most interesting part of the visit was without a doubt the inspection of the wall itself and the explanations of the many intricasies of its design and care in construction, covering aspects such as positioning of galleys, interlocking of blocks, reinforcement, refrigeration, actual concrete placing, subsequent grouting, etc. Other points of interest were the very complicated design of the wall itself, the river diversion plans, with three stages of coffer dams, the spillways, and the very well cut penstock tunnels.

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l'excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d'analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017