Search Documents

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By P. J. Lloyd

There are few data on the composition of discard coal in South Africa, and no overall view of the discards for the entire industry. As a result of work on coal qualities in South Africa, a database was established which enabled a good estimate to be made of the composition of the discard from every mine. The data are presented in the form of histograms of ash, volatile matter and fixed carbon content of the 43 million tons of material which were discarded in 1990. The results are discussed in terms of the closeness of the composition of much of the discard material to presently used power station coal. It is concluded that it is mainly developments in equipment, particularly fluidized bed boilers, which inhibit the wider use of discard coal. However, other factors must be noted, including the relatively high sulphur content of the discards, and the fact that even with the most careful storage the material ages and may become unusable after about 15 years.

Jan 1, 2000

By L. Forsbacka, M. Nakamoto, L. Holappa

Viscosity of the slag is one of the central parameters when producing FeCr in submerged arc furnaces. It contributes to smelting behaviour and reduction kinetics of chromite ore as well as to the Cr recovery by influencing the separation of dispersed metal droplets from the slag. A typical FeCr process slag contains 5-10pct chromium oxides, CrO and CrO1.5. The neural network computation was applied to the evaluation of viscosity for slags containing chromium oxides, and the prediction of viscosity in FeCr process slag was conducted. The main results in this estimation were that the chromium oxides in FeCr process slag lower its viscosity, and that the effect of CrO on the viscosity decrease is greater than that of CrO1.5.

Jan 1, 2007

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African platinum group metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky Reef is low in chromium and does not pose significant melting problems. Concentrates from the UG-2reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8?10-9bar at temperatures of 1550°C to 1600°C). During the converting process, care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation of Fe2NiO4 (trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever-increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3.A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Keywords: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium

Jan 1, 2004

By T. Khumalo, L. P. Coetzer

This paper addresses the impact of the variable speed drive on the particle size distribution in the product of a fully autogenous UG2 grinding circuit. It further discusses the impact of a varying particle size distribution in the product of the mill on the downstream classification and milling circuits. An industrial case study was used and data is presented to illustrate the techniques applied to identify the root cause of the shift in operational efficiency. The results achieved from both the investigation into the shift in plant efficiency and the sub-sequent corrective action taken illustrate that the root-cause methodology used in advance control can be effectively applied on production sites to both detect the shift and identify probable root-causes. The industrial example used confirms that the variable speed drive in a UG2 autogenous milling operation is a critical control parameter to ensure that the plant operates to design specifications.

Jan 1, 2006

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

By J. L. Fuentes-Cantillana, Á. Rodríguez, P. Morillo

Evacuation operations from work places in the case of an emergency are the key to minimising the effects of catastrophic type accidents such as fires, explosions, cave-ins, floods, etc. The correct planning of these operations, having the necessary means for sounding alarms and communicating and suitable training of personnel are the key factors for guaranteeing successful evacuation. The article gives an analysis of the problem in the case of subterranean mining and various types of work developed by AITEMIN in this field, including the development of new alarm and communication means specially adapted to the characteristics of mining operations, development of tools for help in the preparation of emergency plans and experiences in the education and training of personnel.

Jan 1, 2003

By M. Arlandi, J. C. Monge

In this paper, the finite element method is used to obtain deformations of a rock tunnel. More than 3,000 numerical simulations and calculations were carried out. The analysis of this results has allowed to achieve mathematical formulations and graphs, to obtain in advance support monitored displacements in tunnelling construction, so they can be predicted before excavation and supporting woks. The application of the presented formulations and charts will aid engineers to control tunnel monitoring, reducing decision time when problems occur. The analysis is limited to cases involving elastic behaviour of the terrain for tunnels of average to good quality in rock, and to excavation sections of average or smaller dimensions for road tunnels. The results show that, in all cases, mathematical expressions to obtain induced displacements around tunnel excavations, have similar pattern than Kirsch (1898) expressions for circular excavations. As corollary of the achieved results, a method to estimate in situ natural geostress ratio K0=sh/sv , by means of convergence measurements, is presented. In diesem Beitrag wurden die Verschiebungen eines Tunnels durch die Methode de Finiten Elemente berechnet. Mehr als 3000 numerische Simulationen und Berechnungen wurden ausgeführt. Die Analyse dieser Resultate hat es ermöglicht, mathematische Formeln und Grafiken zu entwickeln, die zur Voraussage der Verschiebungen in Tunnel dienen, auch unter Betrachtung der verschiedenartigen Abstützungen. So können die Verschiebungen vor den Erdarbeiten und dem Bau der Abstützung abgeschätzt werden. Die abgeleiteten Formeln und Grafiken werden vor allem einen grossen Dienst für Ingenieure bei der Mithilfe zu zeitsparenden Entscheidungen im Tunnelbau und bei der Tunnelkontrolle leisten. Die analysierten Fälle sind auf eine elastische Modellierung des Baugrunds beschränkt, sowie auf eine mittlere bis gute Qualität des Felsens und auf die Aushebung von Abtragungsabschnitten mittlerer oder geringer Grösse für den Strassenverkehr. Die Resultate zeigen, dass in allen Fällen die hergeleiteten Formeln zur Berechnung der durch den Tunnelbau verursachten Verschiebungen um den Tunnel die gleiche mathematische Struktur haben wie diejenigen von Kirsch (1898) für kreisförmigen Bodenaushub. Als Korollarium der ausgeführten Berechnungen wird eine Methode zur Abschätzung der vorherrschenden in situ Geospannungs-Verhälniss K0=sh/sv angegeben, die von den Messungen der Verschiebungen im Tunnel ausgeht. Dans cet article, la méthode des éléments finis est utilisée pour obtenir les déformations d’un tunnel creusé dans la roche. Plus de 3000 simulations numériques et calculs ont été effectuées. L’analyse de ces résultats a permis de définir des modèles mathématiques et des abaques afin de prédire, avant l’excavation et les travaux de soutènement, les déplacements auscultés pendant la construction du tunnel. L’application de ces modèles et abaques permettra donc aux ingénieurs de contrôler les déplacements durant l’auscultation du tunnel et de réduire le temps de décision lorsque des problèmes surviennent. L’analyse est limitée au cas du comportement élastique du terrain pour des tunnels creusés dans de la roche de moyenne a bonne qualité, et à de sections d’excavation de petites à moyennes dimensions pour des tunnels routiers. Les résultats montrent que, dans tous les cas, les expressions mathématiques permettant d’obtenir les déplacements induits autour des excavations de tunnel, présentent des similitudes avec celles de Kirsch (1898) pour des excavations circulaires. Comme corollaire aux résultats obtenus, une méthode pour estimer le rapport des

Jan 1, 2003

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By Phillip J. Mackey, Rodney T. Jones

"Copper and copper alloys remain key materials for society today, with important uses found in the electrical, transportation, and construction industries. Copper demand is rising, with projections indicating that by 2025 global refined copper demand will increase to 29.5 million tons, up from the 22.4 million tons anticipated for 2015. This will require the opening up of dozens of new mines and numerous new smelters over this time period. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in contributing to meeting the rising global demand for copper. This paper provides a brief overview of the current copper smelting operations in Southern Africa. INTRODUCTION Copper and copper alloys are essential materials for today’s modern world. The familiar green copper patina colour seen on buildings and other structures sometimes belies its true “green” characteristic – copper is essential for key emerging technologies such as wind turbines, tidal generating systems, solar energy systems, electric cars and the like. Consequently, it is believed that there will be continued growth in copper demand in the years ahead. Projections indicate that by 2025, as an example, global refined copper demand will increase to 29.5 million metric tons, up from the 22.4 million ton level anticipated for 2015. This will require dozens of new mines, and of the order of the equivalent of 10 to 12 new 0.5 million tons of copper/year-sized copper smelters (after factoring projected copper produced by electrowinning (EW))—overall, a huge undertaking. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in supplying this rising global demand for copper. Africa’s share of global mined copper production was about 10% in 2014; however this will increase significantly in future if announced new projects eventuate. Southern Africa has an important role to play in this process. The present paper provides a brief overview of copper smelting in Southern Africa."

Jan 1, 2015

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By V. V. Nazimko, A. I. Hohotva, S. N. Alexandrov, V. P. Sazhnev, V. S. Zaharov

Ground behaviour in the vicinity of a roadway has been investigated using a physical model and in situ tests during a roof fall. It was discovered that behaviour of the ground is governed by irreversible displacements of adjacent rock clusters. The cluster is a short-living sector of a rock mass that moves as a solid body. For the lack of degree of freedom, the rock mass must be divided into clusters that are forced to move one after another in space and in time. These clusters permanently rearrange and reform during irreversible (inelastic) ground deformation. The crowded clusters have to yield to each other and alter their velocity and direction of movement to accommodate their motion into the excavation. Such behaviour involves uneven and irregular vertical deflection and the movement of adjacent rock blocks in the roof, sides and floor of an opening. Such movement destroys the symmetry of horizontal displacements with respect to the centre line of the opening. A set of indicators that a roof fall is imminent has been identified. Horizontal displacements and dilation must be controlled in order to maintain the stability of an underground opening. Such a state retains the self-supporting effect of the roof and contributes to rock bolts bearing capacity.

Jan 1, 2003

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

By L. Andrews

Electron microbeam analysis of metallurgical samples covers abroad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion. Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistry can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis complements bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect. This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly.

Jan 1, 2007

Dr H. J. van Eck (Honorary Life Member): "Mr President, I regard it as a signal honour that I was invited to address the South African Institute of Mining and Metallurgy on its 75th Anniversary. I also wish to add my congratulations and good wishes to the many you have already received on this memorable occasion. Seventy-five years is indeed a good age and the achievements of your Institute certainly justify this special celebration. South Africa owes her present prosperity largely to the technological ability and determination of her own people. Members of the Institute contributed in large measure to this great development of our country and through the years have upheld their high reputation for scientific integrity, dynamic enterprise and dedicated service. It was their knowledge which provided the key to unlocking the mineral wealth which lay dormant for countless ages. The history of world mining dates back many centuries. We know of the mercury mines of Spain, the tin mines of Cornwall and the zinc mines of Poland, but it was not until colonization of the western hemisphere started in about 1500 that mining of any consequence began in North America. It is true that the peoples of South America and Mexico had accumulated wealth out of gold and silver, but industrialized mining was not a feature of these agrarian cultures. The mining wealth that eventually developed in North America was based on advances in the technology of processing minerals and served as an incentive to people in other new countries. Big mines were opened elsewhere in the world. From Canada, Mexico, Venezuela, Brazil, Peru, Chile, Bolivia, Rhodesia, Australia, Burma and India, to name but a few, there has been a steadily increasing production of an expanding range of minerals and metals. By the middle of the 20th century the trend was to increase the production and use of such comparatively uncommon metals as cobalt, nickel, titanium, and others, and a great mining rush started to search for, and develop, the deposits of uranium, and related radio-active minerals. It is worth pausing a few minutes to reflect that most of early mining was based on the recovery of virgin metals like gold and silver or easily treated high grade ores of copper, tin and zinc. Today, much of this type of mining would be regarded as picking the eyes out of the mine. With the development of improved ore separating, ore concentration and recovery processes, we developed into bulk mining and bulk treatment and in South Africa we have some very big mines, also outside the gold mining industry at Phalaborwa, for instance. Mining techniques are applied which compare with the best in the world. These large mines could only develop because of the perfection of new concentrating techniques and, of course, because of the development of markets. We have mentioned nickel and cobalt. These names were given to those mischievous mining sprites called nickels and kobolds to whom the suspicious miners ascribed their inability to smelt copper from copper nickel or arsenious copper ores. In South Africa, the presence of minerals was known to the modern Western world as far back as 1497 when Vasco da Gama found the native 'strandlopers' at the St. Helena Bay wearing copper rings. In 1669, after the British East India Company had formed their settlement, they employed miners and assayers in prospecting for minerals and in 1685 found traces of copper in the copper mountain of Namaqualand where some 170 years later a rich deposit of copper was to be opened up. This deposit also had a chequered

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006