Search Documents

By D. Xie, S. Sun

An overview of recent development of CSIRO?s Multi-Phase reaction models will be presented with examples comparing the calculated physico-chemical properties of metallurgical slags with the existing experimental data. The paper will also outline the development of a kinetically based model for molten bath reactors and its application to submerged combustion of coal in a slag bath as well as the reaction between the slag and injected coal particles. The plume model combines established models for the combustion of pulverized fuel with models for the growth and rise of bubbles from a lance or tuyere. This model predicts the extent of de-volatilization and combustion of the coal in the plume, the utilization of oxygen and the exchange rate of oxygen between the gas and the bath as well as the heat transfer rate between the gas bubbles and the bath. The slag reduction model brings together the recently measured rate data and fundamental understanding of the kinetics of CO-CO2reaction with iron oxide containing slags and predicts the changes resulting from injection of coal particles into molten slags. The top-space model covers reactions between gases and molten droplets in the post-combustion zone, where heat and mass transfer between phases results in higher utilization of the fuel values in the partly oxidized gases and transfer of heat to the molten bath. Keywords: Phase equilibria, viscosity, electrical conductivity, slags, kinetics, reaction rate.

Jan 1, 2004

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By H. A. D. Kirsten

Shotcrete has become a strategic component of support in underground mines. The ductility of reinforced shotcrete makes it a safe and economic means of surface support under adverse static and dynamic loads. The ability of ductile shotcrete to sustain load at large deflections enables excavations in squeezing conditions to be stabilized and the safety in excavations subject to rock bursting, to be assured. A Shotcrete Working Group was formed to find the configurations of fibre reinforcement that would give shotcrete the same ductility as when reinforced with mesh. Beams and panels reinforced with various types and lengths of fibre were accordingly tested. A single mix design consisting of river sand, ordinary Portland cement, fly ash, condensed silica fume and gunite dust and segregation suppressant was used. Steel and polypropylene fibre varying in length from 25 to 50 mm were used in nominal contents of 5 % and 0.5% by mass respectively. Beams, panels and control specimens were shot into specially made formers. Suitable mixing procedures were developed for the different types of fibre. The test specimens were shot in a semi-dry mix process. The shotcrete was cured until tested 28 days after shooting. The fibre contents and uniaxial compressive and Brazilian tensile strengths of the shotcrete were determined from the control specimens. The beams and panels were tested in bending in specially manufactured test rigs. The beams were examined for simple supports and fixed ends. The panels were fixed in a manner that simulated underground conditions and were loaded statically under uniform pressure. The beams were loaded and the corresponding deflections measured up to failure. The panels were loaded up to mid-span deflections of 150 mm. The results are presented in the form of load-deflection graphs. The peak loads and ultimate deflections for the fixed end beams were considerably larger than for the simply supported beams for the various types of fibre considered. None of the beams tested, however, were able to sustain load at relatively constant value beyond the peak load. The panel tests showed that 40 mm and 50 mm long steel fibre and 30 mm, 40 mm and 50 mm long monofilament polypropylene fibre reinforcement gave shotcrete the same ductility as mesh.

Jan 1, 1998

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and1580ºC under 0.03 atm, 0.05 atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged toSiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S) systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations, the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80 and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC, respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermo-dynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on a pseudo ternary SiO2? (AI2O3+CaO+MgO) ?(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: chromium, slag, equilibrium

Jan 1, 2004

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By D. Grabowski, Z. Pokryszka

A study carried out in the iron basin of Lorraine (North-East of France) highlighted the existence of under-oxygenated and noxious gas emissions (carbon dioxide, radon…) in vast built-up areas related to former mine workings. Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes in buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, iron mine, pyrite.

Jan 1, 2003

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 24th August, 1977. Dr M. D. G. Salamon (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : C. G. Evans, J. P. Rees, Life Fellows ; S. R. Bryant, H. MacConachie, M. Mrost, and A. W. van Zyl, Fellows; L. T. Campbell-Pitt, F. W. Collins, A. J. Duncan, I. G. Evans, F. W. Kleinschmidt, P. L. Vaughan, R. W. Wallace, and H. Wason, Members. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on 23rd March, 1977, as published in the June issue of the Journal? Agreed.

Jan 1, 1978

By J. D. Bosman

The problems associated with squeezing rock conditions in tunnels are well known and have been extensively investigated in the past. Although squeezing conditions are predominantly found in tunnels developed in weak rock types it has been noted at the No. 6 Shaft of Hartebeestfontein Mine where the host rock consists of hard, brittle quartzites. This paper investigates typical time-dependent deformation mechanisms in the rock at Hartebeestfontein Mine. The paper will focus on observations made in a strike-orientated tunnel that intersected weak quartzite layers, that were sandwiched between two competent quartzite beds. The observed squeezing mechanism is dominated by creep along bedding planes with a soft talcaceous infilling that behaves in a clay-like fashion when saturated in water. Stress-induced deformation processes, some distance into the sidewall of the excavation, force the already fractured periphery of the excavation into the void. A laboratory study of the creep of intact rock and discontinuities collected at this site was conducted to characterize the time-dependent behaviour. The difference in creep rates between the two types of quartzite found at this site is described in the paper. Creep tests performed on the talcaceous infilling material found that its presence allows substantial shear creep along discontinuities. Attempts were also made to simulate the squeezing mechanism observed underground with numerical techniques. Due to the discontinuous nature of the mechanism described above, a viscoplastic displacement discontinuity technique was used as it allowed for the explicit simulation of discontinuity creep. The results of the modelling and how it compared with the observed behaviour are described in the paper. Environmental impact statement The work described in this paper will not cause any new, or contribute to any existing, hazards confronting the environment.

Jan 1, 2000

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

By J. Thompson

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree A study into the stability of strike gullies at TauTona mine was to be carried out. In reaching the conclusions to follow, a three-stage process was followed. ?A literature study as well as discussions with management and workers alike to gain their inputs and perceptions. ?An ESH Department survey into the history of transgression from proper mine standard in TauTona strike gullies. Unfortunately records were found to be scarce and obscure and the importance of better inter-departmental recordings cannot be stressed enough. ?An underground survey of 11 pre-selected gullies distributed in both the UCL and LCL reef horizons. This stage is to carry the greatest weight in the points to be brought forward in this report. The process highlighted and ranked the following areas as the most critical role players in the deterioration of strike gullies: ?Poor blasting practice ?Sub-standard siding depth and lead-lags ?Split sets ?Off line gully development ?Adverse geological features. The following has been suggested to the mine to help reduce strike gully instability. ?Where possible, maintain lead-lags below 7 m?else increase the siding depth to suit. ?Decrease the gully width standard to 1.2 m (especially in ?high risk areas?). ?Discourage drillers from drilling side holes in gully face blast pattern. This will allow for time in which tendon support can be kept up to date. ?Ensure split sets are installed 1 m behind the gully face so as to prevent opening up of fractures. ?Utilize the centre split set in the 1:2:1 pattern to maintain the proper gully line. ?When adverse conditions prevail, it is necessary to apply a special support plan not only to the panel face, but also (just as importantly) to the gully as well. Shotcreting of the gully hanging is a suitable long-term consideration for providing the additional a real coverage needed. List of Abbreviations [CL Carbon Leader M/O Mine Overseer UCL Upper Carbon Leader FOG Fall of Ground LCL Lower Carbon Leader H/W Hanging Wall ERR Energy Release Rate F/W Foot Wall WDL Western Deep Levels ESH Environmental Safety and Health ]

Jan 1, 2002

By V. Tathavadkar

Worldwide TiO2is extracted from natural ilmenite, rutile, and anatase minerals via the sulphateand chloride processes. The sulphate process generates large volumes of less toxic wastes, whereas the chloride process, including the ilmenite-chloride process of DuPont, yields much lower volume of wastes, which are highly toxic and hazardous. The treatment and disposal of such hazardous chloride wastes is both expensive and difficult in terms of long-term monitoring. Besides the waste management and disposal, there is also a shortage of high-grade titanium dioxide minerals in nature, which consequently yields much larger tonnages of sulphate and chloride wastes. In the present investigation we report the results of an alternative titaniferous mineral beneficiation process based on soda ash roasting of minerals. Compared to the conventional processes for beneficiation of TiO2- ores, the alkali roasting of titaniferous offers several advantages including the zero process wastes. In the soda ash roasting process, the mineral is mixed with sodium carbonate and heated above 1023 K in air. The oxidative roasting of ores yields several complex alkali compounds, some of which produce a liquid mixture above 1123 K. In this paper, we have attempted to characterize the composition and physical chemistry of alkali-rich liquid phase. The phase equilibria in the Ti-(M:Fe)-Na-O system are evaluated and compared with the phases formed as a result of roasting reaction. The experimental results revealed that the composition of complex alkali liquid at the reaction interface plays an important role in determining the transport of O2-ions and decomposition of ilmenite. The roles of the crystal structure of mineral phases and their energetics are also emphasized in controlling their decomposition during alkali roasting. The presence of molten alkali in controlling the partitioning of water-soluble alkali salts and insoluble sodium titanate is also explained. Keywords: ilmenite, anatase, alkali roasting, phase equilibria.

Jan 1, 2004

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By A. V. Roschin, V. E. Roschin

Composite ores are more often used for production of iron in connection with reserve depletion of traditional ore crude in the regions with developed metallurgy. In particular, the majority of perspective ferrum-ore deposits of the Urals are presented by titanferous magnetite ores which contain a significant amount of titanium and vanadium alongside with ferrum. Thus, the deposits of titanferous magnetites of the Southern Urals on the average contain about 20 % of Fe, 8,7 % TiO2 and 0,24 % V2O5. Due to a high content of titanium oxides it is impossible or it is inexpedient to process such ores in blast furnaces. During work just on titanferous magnetite ore refractory titanium-containing slags are formed in a blast furnace, and in case of its dilution by ores of different types the titanium due to the small content in slag is thrown out. It is often impossible to separate such ores into ferriferous and titanferous concentrates because ferrum and titanium are present in the same minerals. This work attempts to selectively reduce ferrum in solid oxide and to separate metallic iron from titanferousslag with fast fusion. Solid-phase reduction of ferrum has been carried out with carbon at temperature of 1000? 1300°?. In products of solid-phase reduction the extremely disperse mix of metal iron and only partially reduced titanium oxides have been achieved. It is impossible to separate such a mix mechanically. However, the fast fusion of the mix allowed separating it into cast iron and slag with the high content of titanium. Thus the cast iron contained less than 0,1 % of titanium, and the slag did not contain practically any ferrum.

Jan 1, 2007