Search Documents

By J. J. Schoeman

In South Africa and in the rest of the world, the two mica minerals that have the most important commercial value are muscovite and vermiculite. Muscovite has been making a comparatively small but steady contribution to South Africa's mineral exports since about 1960. Vermiculite mining and concentration were started by the late Or Hans Merensky at Phalaborwa during 1946. Vermiculite has enjoyed good overseas sales since then, and during the past four years has become an important earner of foreign currency for South Africa. The various aspects of the micas that could be of general interest are briefly reviewed, such as the history of their exploitation, their mineralogy and chemistry, and their mining, concentration, production, sales, and future

Jan 1, 1989

By G. Chitiyo

Prediction of pothole characteristics is a challenging task, confronting production geologists at the platinum mines of the Bushveld Complex. The frequency, distribution, size, shape, severity and relationship (FDS3R) of potholes has a huge impact on mine planning and scheduling, and consequently cost. It is with this in mind that this study was initiated. Quantitative analysis of potholes indicates that pothole size (area covered) can be described by two partly overlapping lognormal distributions. These are referred to as Populations A (smaller) and B (larger). The range of observed pothole sizes conforms to a simple double exponential growth model based on Newton's Cooling Curve. A third size range of very large potholes (Population C) that could not be modelled properly within the proposed growth model is interpreted as to represent a very early phase of aggressive regional thermo-chemical erosion and potholing. In general, potholes are dominantly quasi circular with only a subordinate tendency of elongation. In the UG2, potholes with elongated forms are more prevalent in the size range between 20 and 500 m diameter. In the Merensky Reef elongated potholes are more common in the size range above 50 m in diameter. Although not distinctly visible, elongation of potholes in both the UG2 and the Merensky Reef show a net north/south orientation. Using shapes of pothole rims and floor areas, documented for the UG2 in the Waterval Shaft area, it is demonstrated that the northern, down-dip edges of potholes have steeper dips than the southern, up-dip edges. Spatial distribution studies using a uniform quadrant method suggest that in both the UG2 and the Merensky Reef, the potholes are randomly distributed, with a tendency towards clustering. Clustering appears to be more prevalent in the smaller Population A potholes. Bearing all findings in mind, it is found that the model of thermo-chemical erosion of the cumulus floor by new influxes of superheated magma best explains the observed data. Partial to complete melting of the cumulate floor occurred in three phases. The first represents the emplacement of hot magma. This magma, due to turbulent flow and high chemical and physical potential, aggressively attacks the existing floor (crystal mush on the magma/floor interface). Regional erosion is manifested by large, often coalescing potholes. During the second phase, when the magma emplacement process ceased and cooling in situ started, two distinct periods of pothole formation ensued. The first is related to rapid cooling along the relatively steep part of the Newton Cooling Curve, when Population B potholes nucleated randomly and grew rapidly with concurrent convective overturn and largely laminar flow condition. The second period of cooling occurred on the shallow-dipping part of the Newton Cooling Curve. Population A pothole growth became more subdued and nucleation appears to have been, at least locally, clustered. The final phase of this proposed 'super magma cycle' was introduced when chromitite crystallization and precipitation terminated pothole formation. This was followed sequentially by pyroxene and plagioclase crystallization to form the typical cyclic units of the Critical Zone. No suitable proxy could be found for the prediction of pothole density of potholes associated with the UG2 (likely due to limited spatial data coverage), and these are best predicted by extrapolation. The Merensky Reef slope index, in contrast, provides a proxy for pothole density, enabling prediction with reasonable confidence. This predictive model has been verified using underground information. The findings made during the course of this investigation have, when implemented, significant impact. Successful implementation will not only allow enhanced resource and reserve definition, but also better mine planning and scheduling.

Jan 1, 2008

By P. Greenfield

The German steelmaking industry has come up with a novel solution to the problem of waste plastics-grind them into particles and use them in the steelmaking process. Plastics make ideal agents for removing oxygen from iron ore in blast furnaces, and save on oil and coal as well. The aim of replacing heavy oil and coal with plastics in blast furnaces is to use them as reducing agents as well as an additional energy source.

Jan 1, 1996

By B. Friedrich, A. Birich

Gold has been a metal of special importance for mankind for several thousand years. Its outstanding chemical resistance is an important property of this noble metal, but becomes a disadvantage when it comes to gold recovery. The established processes are based on highly aggressive and toxic reagents. Different alternative leaching reagents with a significantly lower toxicity proved to be promising alternatives in the last decades. Major research activities in this field focused on gold ores, so that leaching of secondary resources were not described sufficiently. Based on literature research and extensive experimental investigations, a reagent assessment was conducted for hydrometallurgical gold recovery from electronic waste. It was found that besides thiourea and halides, thiosulfate in particular represents an alternative of major relevance. A variety of different electronic waste (e-waste) specimens were investigated to identify suitable leaching conditions. As a result, an almost complete and selective gold recovery in less than 48 hours from different electronic waste types and components was achieved by thiosulfate leaching. Within the experiments conducted, it was found that the leaching behaviour of cyanide alternative lixiviants differ strongly from leaching of primary ores. Keywords: Gold leaching, cyanide alternative, thiosulfate, electronic waste

Jan 1, 2020

By Godofredo F. Barrios

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings from as fine as 100 microns and coarser have been used. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies which allow an end user to consider urethane screen surfaces for fine screening applications. These technologies allow an end user to use the inherent advantages of urethane with regards to wear resistance while also realizing the benefits that a high oper area urethane screen surface can bring. These benefits include non blinding characteristics and feed capacities that which rival that of traditional stainless steel surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines they are used in conjunction with. There will also be a presentation of case studies of commercial installations where these technologies are utilized. These case studies are from the base metals industry therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints which must be taken into account when considering urethane screen surfaces such as temperature and chemical attacks. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities' and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

By T. Lee

The mining industry, both here and internationally, is continually developing increasingly sophisticated software to compute mineral resource estimates, but these processes cannot compensate for a flawed geological interpretation of the geology of the economic commodity(s) concentrations. Quality assurance and quality control (QA/QC) is becoming increasingly common in association with the sampling and assaying practices within the industry. However, it is rare in the case of a geological interpretation associated with mineral resource estimation. Why? In the context of this paper, QA/QC relates to the use of statistical and graphical tools to show that the geological economic commodity concentrations have been appropriately domained. Domaining is essential to improve the chance of getting a mineral resource estimate right. Commodity value and acceptable concentration variation within a mineral resource can be ingredients that make mineral resource estimation difficult to get right. But it is possible to get it right a very high proportion of the time. It is more likely to occur when inappropriate data consolidation is minimised. In any case, inappropriate data consolidation is significantly reduced when the geological interpretation is strongly consistent with the data and it is demonstrable. To achieve quality global estimates of geological domain concentrations, it is essential that the geology of the prospect is understood sufficiently that the deposit is appropriately domained. Appropriate domaining occurs when sample populations are separated in such a way that only data in harmony with each other within the population contributes to the domain's concentration estimate. The paper will use four brief case studies to illustrate how QA/QC can be used to display data and validate the underpinning geological interpretation through its associated domaining to get it right when it comes to a mineral resource estimation.

Jan 1, 2007

By R. L. Attridge

Namibia's newest mining enterprise, the Navachab Gold Mine, was officially opened by President Sam Nujomo during June 1990. The mine is a joint venture between Erongo Mining & Exploration Company Limited, Metal Mining Corporation of Canada, and Rand Mines Windhoek (Pty) Ltd. Erongo has a 70 per cent interest in the mine, while Metal Mining and Rand Mines hold 20 per cent and 10 per cent respectively. Anglo American Corporation and its associates hold two-thirds of Erongo shares and CDM (Pty) Ltd one-third. The Mine is managed by Erongo Mining & Exploration Company. The property is located some 10 km southwest of the town of Karibib and 170 km west-northwest of the Namibian capital of Windhoek (Fig. 1), the name of the Mine being taken from the farm on which the gold deposits were discovered. Navachab is an opencast operation and was brought into production in December 1989 at a cost of around R84 milion-RS,2 million under budget. The plant is designed to treat 840 kt annually at an average gold grade of 2,6 g/t. This wil produce 1900 kg of gold per year, which at today's prices will earn Namibia more than R60 million in foreign exchange.

Jan 1, 1991

By R. T. Jones

Base metals and platinum group metals can be collected in metallic alloy form, via a wide variety of smelting processes. The recovery, or degree of collection, of the valuable metals is a function of the extent of reduction in the furnace, which, in turn, is indicated by the fraction of iron present in the feed materials that report to the alloy. An equation has been developed that relates the recovery of various metals (such as Ni, Co, Cr, and PGMs) to the recovery of Fe. This recovery equation (for each metal) is characterized by a single parameter (K?) that can either be empirically fitted to the data, or expressed in terms of the equilibrium constant and the ratios of the activity coefficients involved. Data from a number of varied DC arc furnace campaigns are presented to illustrate this behaviour.

Jan 1, 2009

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By A. J. Van Der Merwe, N. A. Barcza, M. Boyes, N. R. Clarke

Oriel Resources has with the support of SRK (Cardiff) and DRA and Mintek (South Africa) carried our a Definitive Feasibility Study (DFS) to recover high grade chrome ore from its Voskhod deposit very close to Chromtau that is near to Aktobe in Kazakhstan. Voskhod is a large podiform ore body that contains nearly 20million tons of chromite grading about 48% Cr2O3 and with a Cr/Fe ratio of over 3/1. Selected bore hole core samples were obtained from the confirmation drilling programme during the DFS phase of the project in 2005 for pilot plant test work to design the mineral beneficiation plant. The chrome ore is characterised by four main types, namely high grade lumpy and chip sized ore, high-grade fine ore, lower grade (subordinate) lumpy ore and lower grade fine ore. Gravity separation tests carried out by Mintek showed that the large density difference between the high grade (at over 3.7t/m3) and lower grade ore (at less than 2.97t/m3 ) should ensure very good separation in the DMS drum and DMS cyclone stages resulting in high recoveries of Cr2O3 - rich chromite ore products. Very high chrome ore grades of up to 64% Cr2O3 and Cr/Fe ratios of 4 to 1 were obtained at an 80% mass yield from selected samples of lumpy and chip ore size fractions. The overall predicted recovery from the design work on the mine and plant is expected to be closer to about 70% of the ROM (Run of Mine) feed. DRA has completed the design of the mineral processing plant to recover about 900 kt/a of chrome ore from the 1.3 Mt/a of ROM feed. The plant has been sized to handle up to 1.5 Mt/a and will also be able to address the variability in ore feed as different regions in the deposit are mined. The lumpy high-grade product and the chips size fraction is expected to grade around 48% Cr2O3 and the fine concentrate between 56 and 58%Cr2O3 The ratio of products is expected to be about 70, 15 and 15 percent respectively but will vary to some extent during the expected 20 year life of the mining operation based on including the associated adjacent Karaagash deposit together with the Voskhod deposit. The prediction of the product split from the processing plant depends on many factors such as the geology, mineralogy, mining, handling and metallurgical processing. An overall process flow model has been developed that covers the ROM ore, the various types of chrome ore feed to the mineral beneficiation plant, the projected products and the subsequent smelting of the chromite ores to produce High Carbon Ferrochromium. The model allows the optimisation of the quality of the chrome ore in terms of Cr2O3 content, Cr/Fe ratio and recovery to be studied. This information can also be evaluated in terms of the economic requirements for smelting High Carbon Ferrochromium (HCFeCr) at a given location. Oriel is planning to supply chrome ore to Ferrochrome plants mostly in China and Russia. The use of the model will assist to maximise the value of the Voskhod project to its owners and also assist the users of the chrome ore in selecting the appropriate supply quality to meet their needs for a given smelter operation. The smelting of high grade Voskhod ore requires a limited addition of about 5 to 7% quartz to flux the MgO and Al2O3 and about 25% coke as a reducing agent to produce an alloy containing from about 65 to 74%chromium depending on the Cr/Fe ratio.

Jan 1, 2007

By D. N. Ferguson

The separation of certain minerals by electrostatic techniques can be difficult due to their similar electrical conductivity, and any technique to improve this can be useful in certain difficult separation applications. Triboelectric differences between mineral scan result in certain minerals acquiring small positive or negative charges prior to inductive electrostatic separation. By changing the polarity of inductive separation, relative changes in mineral recovery can be observed, which may be beneficial. In this brief study a JKTech mineral liberation analyser (MLA) was used to evaluate the effect of polarity change on selected minerals present in the Richards Bay Minerals deposit, and an approximate triboelectric series based on this behaviour is presented.

Jan 1, 2010

By Franz E. Pawlek

Synopsis This is a summary of investigations in the field of pressure leaching carried out at the Institute for Extractive Metallurgy of the Technical University of Berlin-West during the last seven years. The efficient dispersion of gas in a liquid and its dissolutions as well as the events at the phase boundary when leaching ZnS are reported. At the end two examples are given for the use of pressure leaching in the processing of smelter by-products. INTRODUCTION About 20 years ago, experiments were independently started in Canada and in Berlin on the subject of dissolving sulfidic ores without preliminary treatment by means of leaching under increased oxygen pressure. In Canada ammoniacal solutions were mainly employed, and F. A. Forward and his co-workers were successful in applying this process on a large industrial scale1, 2. This process is used in Fort Saskatchewan to produce about 15,000 tons of Ni per year. In Berlin, investigations were started on leaching with acid solutions3, 4. This process had also been used on a large industrial scale in the D.S.A., but the choice of unfavourable working conditions led to great difficulties, and to giving up this process for industrial use. Later on in Berlin work was carried out especially on the kinetics of pressure leaching 5, 6, 7, 8, 9 and its applications to the processing of smelter by-products, in particular of mattes and speisses10, 11, 12, 13, 14. The dissolution of ores and by-products can be subdivided into four steps: 1. the efficient dispersion of the gas, so that its dissolution occurs over as great a surface area as possible, since only the dissolved oxygen reacts with the solid, 2. the suspension of the solid, so that the entire surface can take part in the reaction, 3. the phase boundary reaction, 4. the removal of the reaction products. The first two steps belong to the field of process engineering and will be discussed from this point of view. The aim of these experiments15 was to find out first of all the limits of efficiency of self-sucking stirrers in solutions of low viscosity with regard to the mass transfer. In addition, the effect of ultrasonics in the same reaction system was studied. The experiments were carried out in a lucite container as shown in Fig. 1. Four baffles of 0.1 d width were in the stirring vessel. The height of these baffles was adjustable. For every experiment one litre of liquid was used. An infinitely variable direct current motor, which was fixed with a hollow shaft, served as the driving power for the stirrer.

By N. T. Beukes

An engineering house?s perspective of required inputs in designing a copper electrowinning tank house and ancillary equipment calls for both understanding of the key fundamental controlling mechanisms and the practical requirements to optimize cost, schedule and product quality. For direct or post solvent extraction copper electrowinning design, key theoretical considerations include current density and efficiency, electrolyte ion concentrations, cell voltages and electrode over potentials, physical cell dimensions, cell flow rates and electrode face velocities, and electrolyte temperature. Practical considerations for optimal project goals are location of plant, layout of tank house and ancillary equipment, elevations, type of cell furniture, required cathode quality, number and type of cells, material of construction of cells, structure and interconnecting equipment, production cycles, anode and cathode material of construction and dimensions, cathode stripping philosophy, plating aids, acid mist management, piping layouts, standard electrical equipment sizes, electrolyte filtration, impurity concentrations, bus bar and rectifier/transformer design, electrical isolation protection, crane management, sampling and quality control management, staffing skills and client expectations. All of the above are required to produce an engineered product that can be designed easily, constructed quickly and operated with flexibility.

Jan 1, 2009

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well proven Swiss Tunnel Seismic Prediction System TSP has been substantially augmented for online geological prognosis in underground construction. In its latest version, the Integrated Seismic Imaging System ISIS provides high resolution seismic images of the rock mass around a tunnel face via an array of standard anchor rods. These rods contain 3D-geophones at their tips and can be readily installed during excavation work. A further innovative component of the system is the newly developed high-power repetitive source for application in hard rock: a pneumatic hammer with laser triggering to be mounted on construction machinery. A user-friendly software package permits online data acquisition and processing, 3D-visualization, and a first geological interpretation. Tomographic images of compressional and shear wave velocity fields at fault zones in metamorphic rock of the Gotthard Base Tunnel in the Central Alps are presented. Das langjährig bewährte Schweizer Tunnelseismische Vorauserkundungssystem TSP wurde inzwischen wesentlich weiterentwickelt. In seiner neuen Version, dem Integrierten Seismischen Imaging System ISIS, ermöglicht es hochauflösende seismische Abbildungen des Gebirges im Vorfeld und Umfeld einer Tunnelauffahrung mit Hilfe einer Anordnung von Felsankern, die an ihren Spitzen 3-Komponenten-Geophone enthalten. Eine weitere Neuerung von ISIS ist die pneumatische Hochleistungs-Impulsquelle mit Laser-Triggering. Eine benutzerfreundliche, interaktive Software ermöglicht die online Datenerfassung und -auswertung, 3D-Visualisierung und eine erste geologische Interpretation. Tomografische Abbildungen von Kompressions- und Scherwellengeschwindigkeitsfeldern an Störungszonen in metamorphem Gestein des Gotthard-Basistunnels werden gezeigt. Basé sur de nombreuses années d’expérience, le système suisse, bien établit, de reconnaissance sismique à l’avancement des tunnels (système TSP), a été sensiblement amélioré pour obtenir une prévision géologique en temps réel durant l’avancement de travaux souterrains. Sa dernière version, le Système Intégré d’Imagerie Sismique (ISIS), fournit des images sismiques haute-résolution du massif rocheux à l’avant d’un tunnel grâce à un réseau de tiges d’ancrage standard. Ces tiges, équipées à leur extrémité de géophones 3 composantes, s’installent très aisément durant les travaux d’excavation habituels. Le élément d’innovation récente concern le nouvelle source très répétitive et de forte puissance pour les applications aux roches dures: un marteau pneumatique déclenché par un système à laser. Un ensemble de programmes informatiques convivial permet l’acquisition et le traitement en temps réel des signaux et produit une vue 3D ainsi qu’une première interprétation géologique. Nous présenterons des images de réflexion d’ondes de compression et de cisaillement ainsi que des inversions tomographiques de zones de faille dans des terrains métamorphiques obtenues à l’occasion du creusement du tunnel de base du Gothard, dans les alpes centrales.

Jan 1, 2003

By H. Sekimoto, T. Matsuoka, K. Yasuhara, M. Ota, S. Akutagawa

A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of the material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface. This technique was applied to measure stresses of H-beams used in tunnels. The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction of underground structures. Une sonde magnétique anisotropique est utilisée pour des mesures non-destructives de stress sur la surface d' unmétal ferromagnétique, comme l'acier. La sonde est construite sur le principe de l'effet magnéto-strictif dans lequel les changements dans la perméabilité magnétique due à la déformation du metal est mesurée avec une manière non-destructive, qui peut être alors traduite en valeurs absolues des stress existants à la surface. Cette technique a été appliquée pour la mesure de stress des poutres en H utilisées dans les tunnels. Les résultats montrent que cette méthode peut être l'une des technologies promet tantes concernant les mesures non-destructives de stress pour des constructions sûres de strcutures souterraines. Ein magnetischer Anisotropie-Sensor wird für die zerstörungsfreie Messung von Spannungen an Oberflächenvon ferromagnetischen Materialien wie z.B. Stahl verwendet. Der Sensor kann Änderungen in der magnetischen Durchlässigkeit auf Grund von Verformungen des Materials erkennen, die dann in Absolutwerte der Spannungen an der Oberfläche umgerechnet werden können. Die Methode wurde auf Messung von Spannungenvon H-Balken in Tunnels angewendet. Ergebnisse zeigen, dass dies eine vielversprechende Methode für diezerstörungefreie Messung im Tiefbau ist.

Jan 1, 2003

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981

By M. Bailey-McEwan

The application of refrigeration on deep South African gold mines is mostly achieved through the medium of chilled water which is produced in central installations either on surface or underground. The amount of refrigeration has been increasing rapidly over recent years, and the total installed capacity on all gold mines now exceeds 1000 MW(R), with annual running costs exceeding R100 million for electricity alone. Hence, there are strong incentives to design such installations for optimal cost-effectiveness. The duty required of these installations varies considerably, owing to daily and seasonal climatic changes and the varying nature of the water demand. It has long been recognized that a computer program to predict installation performance as a whole under any given conditions would be highly desirable. An interactive computer program, CHILLER, is described which enables the user to build an installation, consisting of any configuration of cooling towers, water storage reservoirs and packaged water chilling machines. Externally-dictated conditions such as the weather and chilled water demand must be specified, and all quantities under control of the installation, including internal water flow rates and compressor capacity regulators, must be set. The time-varying performance of the installation can then be simulated. Examples are given of the application of the program in the design of a new installation, and in evaluating the effect of any modifications to existing installations.

Jan 1, 1987

By E. J. Magri, R. M. Murray

This paper describes the application of linear programming to the monthly 'set up' planning of stopers' sections on two gold mines. On one of these mines, the purpose of the exercise was to maximize the total stoping production (measured in centares per month). On the other mine, the maximum stoping contribution (rands per month) was required. Maximization was to be achieved through improved planning, independently of the various other productivity improving activities that were taking place at the same time. The results to date show that, when linear programming is used, an average increase of about 9 per cent in stoping production (or contribution) can be obtained for these two mines.

Jan 1, 1978

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017