Search Documents

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

Termination of membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register. Colloquium and General Meeting A General Meeting and Colloquium on 'Heavy-medium separation and ore sorting' was held on 18th September, 1974, at 09h15, in Kelvin House, Johannesburg.

Jan 12, 1975

By J. O. Marsden

The copper industry is cyclical with the price determined by market forces (i.e. the balance between supply and demand for the metal.) The period of each cycle typically varies between 6 to 9 years. These cycles drive decision making for exploration, new project and mine development, mine closures, process improvement, research and development, and technological innovation. The gold industry is fundamentally different from copper in that supply and demand do not, alone, determine metal price and many other factors play a key role, including global and regional financial conditions, political stability, and the global future economic outlook. However, the gold price experiences trends and longer term cycles that similarly drive business decision making. This paper examines developments in the copper industry that have occurred over the past few price cycles (approximately 20 years) and explores how the lessons learned can be applied to gold extraction. A number of specific examples and opportunities are discussed in detail, including; technology development and innovation, cost control and business improvement, material characterization, comminution equipment, biological heap leaching, and concentrate pressure leaching.

Jan 1, 2009

By C. P. S. Barnard, D. G. Krige

Objective justification on economic grounds for expenditure aimed at improving the quality of the underground working environment requires a suitable measure of any improvement in productivity that would result under routine working conditions. For this purpose, a composite production criterion is suggested, as well as its correlation under actual operating conditions with various factors directly affecting productivity and the environment. Of the environmental factors, wet-bulb temperature appears to be the major factor affecting productivity. The production data given indicate that a decrease in the wet-bulb temperature of 1OC can be expected to result, on average, in some 3 to 4 per cent increase in productivity; in the higher temperature ranges, this percentage could be much higher.

Jan 1, 1981

By Manoj Kumar, S. Ranganathan, S. N. Sinha

The reducibility of three different manganese ores with coke was studied. The three ores were reduced to different extents under the same experimental conditions. The investigations showed that in the temperature range of 900-1000 ×C, Fe2O3 in the ore was reduced to metallic iron. MnO2 was reduced to Mn3O4 in all cases except one in which it was reduced to Mn2O3. The kinetics of reduction was controlled by different mechanisms in the different ores. Temperature had a significant influence on the reducibility of the ores.

Jan 1, 2007

By M. Bryson, V. Deeplaul

As a national facility, Mintek?s brief is to conduct high calibre research that allows the most effective utilization of South African resources. The research takes two different forms, with the efforts being directed at both high-risk endeavours that may lead to the development or adoption of new technologies or the reapplication of technologies to potential new operations. Starting in the 80s Mintek began developing a process to upgrade the UG2 ore and invested heavily in projects, equipment and people to service the industry. Some of the highlights of that work that has been conducted here include: ?Development of a milling and flotation process for UG2 ores ?Development of the ?Mintek Process? for maximizing PGM recovery for UG2 ores ?Conversion of the UG2 milling circuits to open circuit ?Development of a robust pilot plant facility for use in plant design studies ?Use of dense media as a waste rejection option ?Use of attritioners in flotation circuits. More recently, and with the future in mind, the following processes are being researched, some of which have already been commercially applied: ?Development of a flowsheet for Platreef ores ?Use of optical sorting technology for upgrading platinum ores ?Use of a mini-plant for reagent optimization studies. Each of the highlights listed above will be discussed in the paper.

Jan 1, 2004

By H. E. Bartlett

This paper deals with the sampling and mass measurement for ore delivered from a shaft to a processing plant and the contribution of the data from these measurements to the metal balances from shaft deliveries to final metal production. Accurate measurement of the grade and tonnage of run-of-mine ore is important for four main reasons; ? It enables the measurement of the production from different profit centres to within statistically determined confidence limits for daily, monthly, or annual averages. The profit centres could be individual shafts within a mining complex or ore treated on a toll basis ? The monthly production at shaft head is compared to the grades and tonnage determined from underground sampling and mass measurement in terms of a shaft call factor ? The sum of the production from the shafts is the input to concentrators. This input is a major part of the total input into a complex with concentrators, smelters, and refineries. In terms of the Codes of Practice for Metal Accounting the inputs are compared to outputs and inventory changes to assess the efficiencies and unaccounted losses or gains at the various stages in the flow of metal from source to market ? On a daily or daily moving average basis, the grades and tons from shafts are monitored and compared against these quantities from underground measurements. This acts as a control on off-reef mining, dilution, and other factors underground. Accurate measurement of grade of ore at the shaft head has been a challenge because of the large particle size. The conventional wisdom has been that ore can be sampled accurately only after it has been milled to give a slurry that is sampled as feed to a flotation process. However, when the ore fed to a flotation plant comes from multiple sources each source has to be sampled separately. So, relying on the grades determined using the sampling of concentrator input with cross-stream slurry samplers is not an option for determining the grade from an individual shaft. Impala has developed a system for sampling and weighing run-of-mine ore from multiple shafts. The system involves sampling the inputs to the plants using cross-belt (hammer) samplers and weighing the deliveries using in-motion railway weighing systems. Many samples are taken. Individually they have a high variance but, as a consequence of the averaging effect of large numbers and as shown by statistical analysis, the mean results are fit for the purposes of daily grade control for shafts and for monthly accounting of production from individual shafts. In the metal accounting systems at Impala, the measurement of input, including ore and toll-treated material is compared to the output in the form of final metal and tailings losses, as well as any inventory change that takes place, in order to determine a final metal balance from mill feed to product. The calculated inventory is compared to that measured, and the difference, or unaccounted- for metal, is then reported as a percentage of input. The balances obtained over several years yields balances for platinum that are below 1% imbalanced. Keywords metal balancing, platinum mines, AMIRA codes of practice, metal accounting, sampling, run-of-mine ore, statistical analysis.

Jan 1, 2014

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

By K. I. Afewu, L. C. Woollacott

Little is reported in the literature that is directly useful for the interpolation film coefficients for the in-pulp adsorption circuits used in gold metallurgy. This can create a problem if the design or operation of these circuits is to be optimized by the use of simulation techniques. To address this problem, a study was undertaken on the influence of mixing intensity, scale, and geometry on the film coefficient in adsorption systems typical of the carbon-in pulp plants used for gold extraction. This, the first paper deals with the influence of these factors on the film coefficient and shows that the specific power to just disperse the carbon in the slurry is an important variable. This variable is also strongly dependent on mixing intensity, scale, and geometry-a dependence that is dealt with in the second paper in the series. From the informatlon obtained, practical scale-up procedures were developed. These procedures are considered to be applicable to resin-in-pulp as well as to carbon-In-pulp plants.

Jan 1, 1995

By J. Portal

One of the key products produced by the mineral sands industry is the titanium dioxide slag, a process that requires grinding of a coarse product down to a valuable saleable product. Traditional methods have included the vertical roller mill in tandem with dynamic air classifiers and, alternatively, two-stage grinding and crushing through an AG mill in closed circuit with a dynamic classifier and secondary gyradisc crushers. The products produced, commonly known as chloride and sulphate slag, are differentiated by the particle size distribution of the final product. The more valuable chloride slag must, by specification, be a product sized in the range between 850 and 100 microns?the more fines generated in the grinding process, the less higher valuable final chloride slag is produced. This paper will explore a technology that is new to both the mineral sands and to other mineral processing industries. Inter particle communition, or IPC as it is known, has been applied in the cement industry to improve the performance of clinker grinding mills. The principle is to create a process of material on material comminution under high pressure that fractures the material along the grain boundaries rather than breaking it smaller than a gap setting in the crusher. The process is now looked at for the TiO2slag producers because of the potential benefits of energy savings and with a minimal generation of minus 100-micron fines. Discussions will revolve around the design and functionality of the Rhodax® both from a process and maintenance perspective, a typical test regime and results on slag grinding. The development of the flowsheet necessary for the process will be examined, the ancillary equipment required and finally the scale-up from the test to an industrial plant will be investigated. Full-scale results of an operating plant will also be given showing the benefits that can be realized. A promising new flowsheet with fines reintroduction to the Rhodax® crusher will be presented.

Jan 1, 2007

1. TRAINING IN ENGINEERING WORK FOR ENGINEERS IN TRAINING 1.1 Registration as engineer in training An engineering graduate who has passed an examination recognised by the Council1 is eligible for registration as an engineer in training in terms of the Professional Engineers' Act2. Application forms can be obtained from the Registrar.

Jan 1, 1979

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987

By M. M. Oosterveld

Diamonds are mined from ancient raised beach deposits in southern Namibia where complex geological controls have resulted in patchy diamond distribution, largely related to irregularities (trapsites) in the bedrock. The distribution of the number of diamonds per sample is a discrete, reverse- J shape distribution which can be characterized by two parameters. These parameters have been transformed into a Beta and Theta Contribution which can be interpreted as reflecting the 'quantity' and 'quality' of the trapsites. The relationship of statistical parameters, obtained during the sampling of an ore deposit, to the geology of the deposit is an important element of ore reserve estimation. The large-scale regional trends in the contributions have been explained in terms of the geology.

Jan 1, 1987

By J. A. C. Diering

All underground openings are three-dimensional, and in many cases it is not valid to analyse two-dimensional sections. This has been a problem in the past owing to the magnitude and complexity of three-dimensional stress analysis. In this paper a three-dimensional boundary element approach, using non-conforming quadratic elements, which is specifically applicable to underground excavations, is described. In addition, the philosophy of application of stress analyses is discussed. Three case histories are presented to demonstrate the practical nature of the approach as a tool in solving mining problems.

Jan 1, 1987

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analysts' inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted `floor' value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009