Search Documents

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009

By J. Alexis, G. Ye, E. Burström

Over the past twenty years the 3 MW DC arc furnace at MEFOS has been frequently used for development of new processes. These processes include recovery of valuable metals from slag, sludge and dust from steel and other metallurgical industry, treatment of ashes from power plant and incinerators, smelting reduction of minerals and zinc recovery from EAF dust. The process characteristics of the DC arc furnace operation in terms of: ? selective reduction, ? total reduction, ? process stability and flexibility, ? dust carry-over, ? thermodynamic conditions provided in the hot spot area, ? precision in composing slag products These are analysed and described in this paper based on technical results from selected test campaigns over the years and thermodynamic considerations. The electromagnetic properties of DC arcs beneath the electrode have been studied by CFD simulation. The calculated result enables us to understand some interesting technical phenomena observed. The heat balance has also been considered based on data obtained from test campaigns and heat balance calculation.

Jan 1, 2004

By H. Immink

Keywords: Kyoto Protocol, carbon credits, global warming, energy, auditing Climate change is nowadays being taken increasingly seriously, and the link between global warming and the carbon dioxide released in the generation of energy is coming under increasing scrutiny. The Kyoto Protocol was signed in 1997, after five years of negotiation. So far, about 84 countries have ratified this agreement, under which terms developed countries have strict targets linked to their 1990 level of emissions. However, ?greenhouse gas? (such as carbon dioxide) emissions continue to rise alarmingly. According to the World Resources Institute, greenhouse gas emissions in the USA increased 13% from 1990-2002, while Australia recorded a 22% increase. In contrast, the European Union, a Kyoto signatory, has seen a small decline in its emissions during the same period. This is led by the UK and Germany, who reduced their emissions by 15% and 19% respectively. The concept of ?carbon credits? provides a funding mechanism for companies in the developed world to compensate for some of their CO2 emissions by paying companies (trading credits) elsewhere in the world to undertake projects to bring about reductions in emissions. In the southern African mining industry, it will be possible to get refunded for undertaking voluntary emission-reduction projects. Concern about the environment is creating business opportunities. A preliminary calculation has shown that various projects in South Africa (those in the pipeline, with quite a high likelihood of coming off) could earn a combined total of about R2.5-billion, under the initial phase of the Kyoto Protocol's carbon-credit scheme, which allows developed-country companies to trade credits with developing countries. A number of local companies are planning projects that could comply with the Clean Development Mechanism (CDM), in which they will implement techniques to achieve certified emission reductions (CERs) of greenhouse gases. In order to prevent abuse of such a system involving vast sums of money, vigorous audits need to be carried out. A company has to prove it has made real changes and is not simply conducting business as usual under a cloak of claimed environmental improvements. PricewaterhouseCoopers has applied to become one of only a few international agencies that will be accredited to conduct validation and verification of the credits, by auditing what is called the ?designated operational entity?. An independent validator needs to confirm that the project meets the strict requirements of the Kyoto Protocol. The company has to demonstrate that it?s not business as usual. So, if you refurbished every five years, the next refurbishment is not a good CDM project, unless you can demonstrate that you will do something beyond the maintenance - that is what can be registered. So, Kyoto intends to get additional projects going, and the money for that is actually quite good - prices of 14 euros per ton of carbon dioxide not emitted have been seen. The price depends on who takes the risk for non-delivery if a project doesn?t deliver the emission reductions on time. The highly energy-intensive South African mining industry is heavily dependent on coal. There should be many opportunities for the pyrometallurgical industry to come up with creative ideas to reduce emissions, and there is now an additional financial incentive to encourage this. Companies can actually get money in return for doing these types of projects, in addition to the contribution to corporate social responsibility.

Jan 1, 2006

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

R. C. J. Goode (President): South Africa is known for its sunshine and mineral deposits-especially its gold and its diamonds-and as this year marks the 75th Anniversary of the establishment of the South African Institute of Mining and Metallurgy, it is appropriate that I say a few words about mining and metallurgy and the part this industry and our Institute has played in the life of this country. Africa, as the Dark Continent, with its fascinating tales of Prester John, Ophir, Queen of Sheba and its myths and legends has throughout the ages fired the public imagination. Pharaoh Necho, 600 years before the birth of Christ, sent an expedition from Egypt around the Cape to probe this strange land. The gold for King Solomon's throne was said to come from Monomotapa-the country now known as Rhodesia. Centuries later the Arabs and Portuguese searched for this mineral wealth. The Arabs found little gold but unfortunately established a lucrative trade in black slaves. Now let us take a brief look into the closing stages of the Stone Age when the indigenous population of the lower portion of this continent consisted of the Bushmen, a nomadic hunting people who knew no metals and kept no stock, and the Hottentots who were a pastoral folk with cattle and sheep. Then somewhere about the 11th century the Bantu started their long migration southwards and brought with them the knowledge of smelting of iron ore. One of their settlements was here in Johannesburg on the Melville Kopje at Emmarentia. These people were the first miners and metallurgists on the Witwatersrand and the beautifully preserved iron smelting furnace constructed nearly 1,000 years ago is a tribute to their technical ability. This ability to use iron to make better spears for hunting or to fashion hoes for cultivating the soil led to their establishment as a superior tribe. The earlier Bushmen were pushed back to the inhospitable swamps and deserts and the Hottentots fled to the south. The Bantu also knew the art of copper smelting. In the days of the Dutch East India Company, at the end of the seventeenth century, Bantu workers brought copper from the north-west Cape to Simon van der Stel, but it was another two hundred years before the white man turned this to advantage. Stories of the Bantu mining gold spurred the early European hunters to travel deeper into the heart of Africa in search of wealth, and we are told that Karel Kruger, in 1834 whilst leading an ivory hunting expedition, discovered gold on the Witwatersrand, and took samples to Cape Town; but when he returned with a larger expedition a few years later his party was attacked by Moselekatze's Matabele near Potchefstroom. Kruger was killed and only the legend survived. The real spur to mining in this country was the discovery of diamonds in Griqualand West in 1867. The field seemed fabulously rich and diggers flocked to the scene from the four corners of the earth. With them came Cecil Rhodes, Barnato, Beit and some of the finest mining and financial brains the country had yet seen. These giant entrepreneurs were not tempted by the small deposits of gold in the Barberton and Pilgrim's Rest areas when these were made a few years later but

By R. Boom, J. Halder, B. Snoeijer, B. Deo, A. Overbosch

Operational data of BOF and the slag samples for different starting conditions of phosphorus(0.06–0.26 per cent P) and silicon content (0.3–1.2 per cent Si) of hot metal have been analysed. The contribution of parameters that are well known to affect phosphorus distribution at tap, like basicity, temperature, FeO content of slag, slag mass etc., is investigated through the models of ionic theory of slag, optical basicity, regular solution approach and molecular theory of slag. The best overall results are obtained by the model based on molecular theory of slag in which several operational parameters are also incorporated. The investigations of different slag samples, based on optical, SEM, EPMA and X-ray studies, reveal the effect of MgO and Al2O3on slag morphology and phosphorus distribution in different phases. It is important to consider phosphorus distribution ratio in the solid and liquid part of slag. The solid part of slag, which is mostly dicalciumsilicate, can contain up to 5 per cent phosphorus. The phosphorus content of the liquid part of slag may depend upon the phosphorus content of hot metal or phosphorus load of slag. It is found that incorporation of effect of dicalciumsilicate in the model improves the accuracy of prediction. For better process control, the addition of iron ore towards the end of blow must be avoided while treating high phosphorus hot metal or during the production of ultra low phosphorus steels. Keywords: steelmaking, BOF, phosphorus distribution, slag morphology, MgO, Al2O3,dicalciumsilicate, process control, models

Jan 1, 2004

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By R. Rumpold

The platinum group metals (PGMs) palladium, platinum, and rhodium represent the key materials for automotive exhaust gas treatment. Since there are currently no adequate alternatives, the importance of these metals for the automotive industry is steadily rising. The high value of PGMs in spent catalysts justifies their recycling. The state-of the-art technology is to melt the ceramic carrier and collect the precious fraction in a liquid metal bath. As the feed material has quite high melting points, huge amounts of energy are required for this process. Hydrometallurgical treatments of the spent catalysts offer the possibility to recycle the PGMs with less energy and time demands. Moreover, automotive catalysts contain further valuable materials to improve the exhaust gas treatment. These compounds, like cerium oxide, cannot be recovered in pyrometallurgical processes. This paper deals with a special process that uses hydrometallurgical principles to recycle the valuable metal fraction from spent automotive catalytic converters. Hydrochloric acid in combination with hydrogen peroxide is used as leaching agent. This combination selectively dissolves the PGMs and the cerium, which can be recovered in separate steps. As the leaching solution is regenerated and reused, wastewater generation is minimized. Furthermore, the process residues constitute potential byproducts.

Jan 1, 2012

By K. C. Corin, M. S. Manono

The drive to reduce water usage globally has led to the mining industry reassessing its water usage - owing to past environmental degradation due to effluent discharge, tailings disposal and process water seepage into the water-table (Haggard et al., 2015). Factors such as water scarcity and environmental restrictions have created the necessity for recycling of process water in mining and other industries. Water recycling, however, causes an accumulation of ions in the process water, which may affect the strength of reagent action on the target mineral and in turn critical aspects of flotation may be impacted. Prior studies have shown that certain ions have specific effects on flotation: for example, calcium and copper have been found to enhance the adsorption of depressant onto gangue (Feng et al., 2013, Wang et al., 2016). Calcium and sulfate ions have been seen to give a higher concentrate grade than other ions present in process water (Manono et al., 2012). An increase in ion concentration will increase the mineral grade due to a decrease in entrainment (Corin et al., 2011). This study considers the impact of ion accumulation on reagent action and flotation response. Keywords: Flotation chemistry, water quality, ionic strength

Jan 1, 2020

By Kurt RP Petersen, Hendriena van der Walt

With the decline in fine diamond production from the Argyle mine in Australia, there is a greater emphasis on efficiently treating the finer size fractions through a DMS circuit. Although it is generally well understood that smaller diameter cyclones are more appropriate for this application, practical results do not necessarily meet this expectation. In this paper the operational performance of particular sized cyclones throughout the group was compared. Based on the results there is evidence that under certain practical operating conditions, small cyclones are not necessarily best for fine size particle treatment, particularly given the production pressures faced by all mines. However, there seems to be considerable merit in using larger sized cyclones, which tend to exhibit less performance variability, irrespective of operation conditions.

Jan 1, 2006

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By N. C. J. Dempers, J. A. L. Parker, R. A. Wildenboer

More than half of global cobalt reserves are located in the Southern African Copperbelt, stretching over the northern tip of Zambia and southern area of the Democratic Republic of Congo. In these areas, cobalt is not typically produced as a primary product but as a byproduct of copper production. Ores from this region often contain uranium, which is readily leached under typical copper leach conditions and enters the process. Uranium does not pose a challenge to copper production, but it becomes a significant problem when it follows cobalt to the cobalt precipitation process and results in unacceptably high levels of U in the final Co product. This paper evaluates the existing process technologies that can be used to remove uranium from cobalt-bearing process streams, including phosphate precipitation and ion exchange. Advantages and disadvantages of the uranium removal processes are discussed, and important design considerations are highlighted.

Jan 1, 2023

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world?s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of ca. 160 ? 250 Mt; however, all previous attempts to extract the PGE from this ore type proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas arsenide- and sulphide-PGMs, making up ca. 25 per cent of the original Pt content of the ore, largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd)-oxides or hydroxides, or in iron-hydroxides, Mn?Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2012

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By A. R. Leach

Anomalous mining conditions can be described where the level of hazard is increased relative to normal conditions within a mining area. Normal conditions would be those defined as a Ground Control District in a mine’s code of practice, and for which mine standard support layouts are generally developed. It has been found that up to 80% of fall of ground accidents occur where anomalous mining conditions exists, typically in the vicinity of geological weaknesses. These areas require specific attention to ensure they are readily anticipated and identified and that appropriate strategies are used to reduce the hazards associated with them. As part of SIMRAC project GAP 607 checklists to aid identification and best practice mining methods were identified for a range of geotechnically anomalous conditions.

Jan 1, 2003

By R. C. W. Webber

Mining up to depths of 5 000 m would be a world first and, accordingly, no previous experience in the determination of acceptable heat stress limits, criteria or indices is wholly applicable. However, some South African gold mines are already operating at depths beyond 3000 m and much of the knowledge gained in reaching and working at such depths will be helpful in making adequate provision for acceptable environmental control at the greater depths being contemplated. Accordingly, it is necessary to take cognisance of the industry?s experience in deep-level mining and of standards and regulations already established in South Africa and elsewhere in order to ensure acceptable working conditions and control standards, that compare favourably and defensibly with those in other mining industries. The local and international use of heat stress limits, criteria and indices were investigated as it was necessary to determine to what extent any other indices, limits or criteria would be applicable to South African deep mine conditions. In addition, it was necessary to establish whether there was a single heat stress index that could be used for South African ultra deep mining conditions. It was found that an appropriate combination of heat stress indices would be required in planning for and ultimately controlling thermal conditions in ultra-deep mining. The depths being contemplated and the concomitant potential heat hazard present too great a risk for reliance on a single environmental component of heat stress, such as wet-bulb temperature at present in common use locally. The study recommends that a heat stress index, preferably Air Cooling Power (ACP), be used to design an ultra deep mine?s ventilation system and that wet-bulb temperature be used to monitor and control the system once it is implemented.

Jan 1, 2003