Search Documents

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

"Chairman: Professor J. Elbrond Rapporteur: Miss V. E. MartingPapers.Aids to planning production in coal mines by F. H. Deist and M. P. RobertsCapacity calculations, investment allocation and long-range production scheduling in German coal mines by F. L. WilkeOre reserve evaluation and open pit planning by J. M. Marino and J. P. SlamaThis session was devoted to the economic aspects of planning and scheduling. After Dr F. H. Deist had introduced the paper Aids to planning production in coal mines, Dr T. V. Falkie summarized the following formal contribution prepared jointly with Dr R. V. Ramani, describing the work that has been done at the Pennsylvania State University in the development of simulation programs for mine planning over the past 15 years:During the late 50's and early 60's, Monte Carlo simulators were developed to model continuous miner-shuttle car transport systems, track haulage systems, belt conveyor networks, etc. In the mid-60's attention was directed towards deterministic simulation of equipment performance, given the equipment characteristics and the system profile. In the late (10's all these systems (miners, shuttle cars, belts and trains) were integrated together to form a complete coal mine simulator and the program could predict the output potential of the system, given the mining dimensions, method and equipment employed. The actual sequence of coal-cutting operations is entered into the computer through the use of a special programming language which permits any type of mining configuration to be simulated. The simulator is hybrid in nature in that the shuttle cars, trains and belts are simulated deterministically, whereas rate functions with delay frequencies are entered for the continuous mining operations of sumping, shearing, fleeting, cleaning, etc. With suitable manipulation of the data, the program may be applied to all belt or conventional mining sections. Most of these simulators were developed through the assistance of grants from the Department of Mines and Mineral Industries of the Commonwealth of Pennsylvania and are available from the Coal Research Board of the Commonwealth,"

Jan 1, 2014

By R. Perlman

This paper describes the various new computer-aided techniques being used by economists in the construction of economic models. It discusses the relevance of these techniques to mining industries. In particular, it describes their role in making it possible to obtain better estimates of future price and demand developments on the markets on which metals are sold, and how these estimates can be used to improve forward planning by mining companies.

Jan 1, 2014

By G. Asbjörnsson, E. Hulthén, P. Papadopoulou, C. M. Evertsson

Crushing plant managers need to assess, manage, and communicate the environmental impact induced by their crushing plant operations as a step towards the sustainable development of the company. However, performing reliable environmental impact calculations of crushing plants can be challenging when the availability of operational and emission data is low, and when the company’s environmental expertise is not adapted and connected to plant operations (or does not currently exist). To address these challenges, this paper proposes a practical approach where the lifecycle assessment methodology (LCA) is combined with process simulations in a web-based tool. To describe what functionality such a tool should have to be incorporated into a company’s workflow, the system that surrounds a crushing plant is analysed. Further, a case study with a three-stage crushing plant is introduced to showcase how the simulated power draw results produced with the beta version of the tool can be compared to measured sensor data from the crushing plant for one operational day. The results indicate that the simulation tool can provide an adequate estimation of the specific energy for the different material fractions and give an overview of the environmental impact of the process caused by electricity and explosives consumption. Plant managers and operators can use this tool to calculate the environmental impacts of their plant and simulate how different operational strategies influence them. Keywords: LCA, environmental impact, coarse comminution, crushing plant

Jan 1, 2020

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023

By N. Mashaba, D. Botha

The aims of this study were to investigate the factors that influence women’s engagement in technical positions in the South African mining sector and to determine what could be done to promote their successful participation. A convergent parallel mixed-methods research design was used to ascertain the factors that facilitate, inhibit, and influence engagement. In the quantitative phase of the study, questionnaires were circulated to women employeees; and in the qualitative phase, semistructured interviews were conducted with employer representatives, most of whom were human resource personnel. Confirmatory factor analysis showed that the three-factor structure (vigour, dedication, and absorption) of the Utrecht Work Engagement Scale fit the sample data reasonably well. Although there is room for improvement, respondents demonstrated acceptable levels of engagement in their work. On the other hand, the qualitative findings showed that employee engagement is impacted by unfavourable working conditions, work–life balance, and the mining industry’s male-dominated work culture. The findings showed that employee engagement should be elevated to a core human resource function. To increase the participation of women in mining, human resource professionals are encouraged to collaborate with mine supervisors, managers, and employees to develop programmes that promote employees’ absorption in and dedication to their work.

Nov 6, 2023

By J. Uys, P. J. Mokganya, J. Olwagen, R. C. W. Webber-Youngman

This article discusses the critical role of leadership in the technology adoption process within organizations, particularly in industries like mining, where innovation is essential for maintaining competitiveness and operational efficiency. It highlights the limitations of traditional technology adoption models, such as the Technology Acceptance Model (TAM), Diffusion of Innovations (DOI), and Unified Theory of Acceptance and Use of Technology (UTAUT), which focus on individual factors and overlook the strategic and organizational roles of leadership. The study proposes the Ambidextrous Leadership-Technology Adoption (ALTA) model, which integrates leadership styles such as transformational, transactional, adaptive, and ambidextrous leadership into the technology adoption process. The model emphasizes the balance between exploration (fostering innovation) and exploitation (ensuring operational efficiency). The findings suggest that transformational leadership fosters innovation by encouraging risk-taking and creativity, while transactional leadership ensures efficient technology integration. The article also identifies key barriers to technology adoption, such as organizational resistance to change, which can be mitigated through adaptive leadership that addresses employee concerns. The research emphasizes the importance of a supportive organizational culture and cross-functional collaboration, which are essential for successful technology adoption. The study concludes by offering practical recommendations for leaders to foster a culture of innovation, manage resistance, and balance short-term efficiency with long-term technological advancement.

Nov 27, 2024

By U. Sachse

This paper explores a systematic approach for mining decision-makers to use when faced with choosing which method to use for a specific rockpass length. The different excavation methods available in the broad South African mining industry are compared against a number of critical parameters, as applied to rockpasses of varying length. This approach is not meant as a definitive, prescriptive planning tool, but rather as a proposed approach to enable designers and planners to choose the best system to excavate their specific rockpasses

Jan 1, 2005

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012

By Z. Levinson, R. Dimitrakopoulos

A mining complex is an engineering system where raw materials are extracted from several mines, processed, transported, and sold to the market. The uncertainty and local variability of material grades and their locations within the related mineral deposits are critical for determining the optimal life-of-mine extraction sequence, destination policy, operating modes, and capital investment decisions, which define the production schedule of a mining complex. Infill drilling is used to further characterise a mineral deposit and reveals information that changes the representation of the resource model and potentially the resulting optimal long-term production schedule. A self-learning reinforcement learning approach is proposed to determine the optimal drilling locations that maximise the net-present value of the long-term production schedule and the associated financial forecasts by adapting the schedule to additional information. A case study at a copper mining complex demonstrates a $70 M increase in project value by collecting drilling information with a $1 M budget.

Sep 1, 2021

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014

By W. Pulles

Mining can adversely affect water quality and poses a significant risk to South Africa?s water resources. Proactive management of environmental impacts is required from the outset of mining activities in order to reduce this risk. Major strides have been made over the last 7 to 8 years, by both the Department of Water Affairs & Forestry (DWAF) and the mining industry, in developing strategies and management plans for the effective management of water within the industry. This has largely been achieved through the development of joint structures where problems have been discussed and addressed through cooperation. This process, which was started around 1991, has continued through to the present time. The mining sector management strategy has been developed at a number of different levels as follows: ?A detailed Management Plan, that sets out strategic objectives, broad strategies and functional and organizational arrangements. ?Operational Guidelines, that define and document specific operational procedures. ?Technical Guidelines, that define and document best practices for pollution prevention and impact minimization from mining operations. The Technical Guidelines consist of Best Practice Guidelines (BPGs) and Regulations.

Jan 1, 1999

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, 'What is the best way to power this mine?', they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective and quantitative decision-making approaches to evaluate alternative energy delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision making tool and the decision tree-based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2012

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By J. Levin

The Bond standard grindability test provides a Work Index that is widely used to estimate the energy required for grinding, but the test cannot be applied to fine materials such as plant tailings and middlings. For such materials, a comparative grinding test must be used in which a reference material from an operating plant is ground in a laboratory mill to determine the 'equivalent' energy consumption per revolution of the laboratory mill. As the Bond grindability test mill and its operating conditions are specified, its equivalent energy consumption per revolution should be a constant, here designated as B. Once B has been determined, the mill can be used to estimate the grindability of fine materials without the need for reference materials. A value of B can be calculated from any Bond grindability test, and 245 tests that were conducted at Mintek were examined to determine its value. A wide range of values was found, but most of them were grouped around 198 x 10- 7 kWh/rev, which is taken as the best estimate of B that is available at present. Values of B that are not close to this figure are obtained from materials for which the Bond grindability test gives misleading or 'spurious' Work Indexes. These spurious Work Indexes lead to the apparent departure of B from its true value. Some limitations of the Bond grindability test arise from its use of a mill without litters and of screening, instead of classification, to close the circuit.

Jan 1, 1989

By H. Uygucgil, C. Kwang

The use of remote sensing and geographic information system techniques in mineral exploration is still underutilised. There is a need to explore the potential of new robust remote sensing and geographic information system techniques in the field of mineral exploration. In this study, we mapped the argillic alteration associated with epithermal gold-silver mineralisation. A band ratio of band5/band6 and Crósta technique on Advanced Spaceborne Thermal Emission and Reflection Radiometer within the Google Earth Engine Environment was applied. The bands 5 and 6 were selected for the band ratio after critically analysing and comparing the illite spectral extracted from the Advanced Spaceborne Thermal Emission and Reflection Radiometer image and the illite spectral obtained from the United States Geological Survey spectral library. The band ratio and Crósta technique identified and mapped the Ovacik goldmine and other argillic alteration zones. Even though both methods mapped out the argillic alteration zones associated with gold-silver mineralisation, the Crósta technique produced the optimal argillic alteration. The study demonstrates the analytical capabilities of Google Earth Engine in image processing and analysis for mineral exploration, such as discovering hydrothermal alteration associated with mineralisation.

Jul 23, 2025