Search Documents

By M. Vandewalle

What separates the support of mining openings from the support of similar civil engineering structures is the fact that mine openings have to survive large deformations as a result of changing stress conditions induced by progressive mining. Steel fibres impart to concrete and shotcrete a high degree of ductility which not only allows the shotcrete and concrete linings to absorb important rock movements but also to increase its bearing capacity by a redistribution of the loads. A range of applications will be discussed technically and economically.

Jan 1, 1998

By U. C. Galimidi, J. M. Stewart, A. J. Van Rensburg

The effect of body movement on convective heat transfer from a man performing a block-stepping task was investigated experimentally by direct measurements of convective heat transfer. A series of experiments was conducted in which a nude man was required to stand at rest or to block step at 12 and 24 steps per minute. Wind speed, which was kept constant during each experiment, spanned the range 0,5 to 3,5 m/so Air temperature was kept constant at 43 °C in all the experiments. The results showed conclusively that the convective heat-transfer coefficient depends on the stepping rate. The effect of body motion can be regarded as being equivalent to an increase in the velocity of the free stream. The equivalent increase in air speed was found to be 0,36 and 0,77 m/s for 12 and 24 steps per minute respectively. Data from various sources, including the present study, indicate that wind speed should be increased by about 0,30,0,55, and 0,80 m/s to account for low, moderate, and vigorous body movements respectively. These findings are of direct relevance to the practical assessment of heat stress.

Jan 1, 1979

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

By R. Kumar, N. R. Mandre

"The beneficiation of iron ore slimes by selective flocculation was studied. Polyacrylamide (PAM) and guar gum were used as flocculant, along with sodium hexametaphosphate (SHMP) as a dispersant. The samples collected were initially subjected for chemical and mineralogical studies. The mineralogical studies indicated the presence of haematite and goethite as the principal iron-bearing minerals, with quartz and kaolinite as gangue minerals. The selective flocculation tests showed that the Fe grade can be enhanced from 58.24% to 64.60% Fe at a recovery of 66.33% using polyacrylamide as the flocculant. A Fe grade of 63.20% at a recovery of 68.04% was obtained using guar gum as flocculant. The efficacy of the studies was analysed using a separation index, which indicated that the higher separation index was obtained with the tests employing polyacrylamide as the flocculant. IntroductionIndia is endowed with huge reserves of highgrade iron ore and is one of the prominent producers in the world. As the high-grade iron ores have been exhaustively mined, it has become imperative to use low-grade iron ores, fines, and slimes to meet the growing demand. Also, generation of fines and slimes during mining and processing contributes to loss of minerals to the extent of 30% of the total value (Mandre and Panigrahi, 1997). These fines/slimes are often discarded as waste into tailing ponds, containing considerable amounts of iron. Therefore beneficiation of tailings/slimes has become necessary for optimal utilization of the resources.In recent years, interest in recovery of valuable minerals from low-grade ores, slimes, and tailings has increased worldwide. These activities are initiated not only to recover minerals but also to address various environmental issues associated with fine particle treatment. The literature reveals that several technologies have been employed in this regard, including flotation, advanced gravity separation, and high-intensity magnetic separation. However, these processes are found to be ineffective for fine particle treatment due to lower collision probability in flotation, decreased gravitational effect in gravity separation, and reduced drag force in magnetic separation, among other factors (Batisteli and Peres, 2008; Das et al., 2007; Dworzanowski, 2012; Rocha, Caneado, and Peres, 2010). Therefore, it is in this regard that selective flocculation has gained importance in treating slimes in recent years."

Jan 1, 2017

By J. Xiao, Y. Jiang, Y. Tanabashi, Z. Song

Modelling the effect of blasting-caused damage, anisotropy of rock masses and excavation sequence on deformational behaviour and stability of large-scale underground caverns is important in the design and information-oriented construction of the pumped storage power plant. A powerful three-dimensional numerical method that can be applied for that purpose is presented in this paper. Damaged range caused by blasting and mechanical properties of rock masses near to the walls of caverns are determined by using the back analysis approach in which three lines of the measurement results during the arch part excavation process were used to verified the simulations. Finally, applying the improved model and properties of rocks, the cavern stability and reinforcement effect of the preliminarily designed support system are also estimated for the safety in the bench excavation process. La création de modèles des effets relatifs aux dommages résultant des explosions, à l’anisotropie des masses rocheuses et à la séquence d’excavation quant au comportement à la déformation et à la stabilité des cavernes souterraines de grandes dimensions est une étape importante dans l’étude et la construction sur ordinateur de centrales hydrauliques à accumulation par pompage. Cet article traite d’une méthode numérique tri-dimensionnelle puissante applicable à cet effet. La gravité des dommages résultant des explosions et les propriétés mécaniques des roches à proximité des parois de la caverne sont déterminées par une analyse du fond dans laquelle les simulations sont vérifiées à l’aide de trois lignes de résultats de mesures prises durant le processus d’excavation de la partie arche. Finalement, la stabilité de la caverne et les effets du renforcement du système de support préalablement conçu sont estimés par application du modèle amélioré et des propriétés de la roche, pour application à la sécurité durant le processus d’excavation en gradins. Nachahmung der Wirkungen von durch Explosionen hervorgerufenen Schäden, Anisotropie der Gesteinsmassen und der Ausschachtungssequenz auf das Verformungsverhalten und die Stabilität großräumiger Untergrundhöhlen ist für das Design und den informationsorientierten Bau von Pumpenkraftwerken wichtig. Entsprechend der Vorgaben in dieser Arbeit kann ein leistungsfähiges, dreidimensionales numerisches Verfahren für diesen Zweck eingesetzt werden. Der durch Explosionen und die mechanischen Eigenschaften des Gesteins bedingte Schadensumfang im Bereich der Höhlenwände kann mit Hilfe eines retroversen Analyseansatzes bestimmt werden, bei dem die drei bei der Ausschachtung resultierenden Messlinien dazu genutzt wurden, die Simulationen zu bestätigen. Abschließend wurde außerdem durch Einsatz verbesserter Modelle und Gesteinseigenschaften die Auswirkungen vorläufig entworfener Unterstützungssystem auf die Höhlenstabilität und Verstärkungswirkungen hinsichtlich der Sicherheit bei Böschungsausschachtung abgeschätzt.

Jan 1, 2003

By J. L. Fuentes-Cantillana, J. B. Solar Menéndez, A. O. Cámara

The Principality of Asturias is a region situated in Northern Spain with two centuries of tradition in underground coal mining. In addition, its uneven relief has obliged the construction of a great number of tunnels both for railways and roads. Basing on this experience and an ever increasing need to improve on safety, the Barredo Foundation dependent on the Regional Government and the University, provides and manages a Centre for Research of Fires and Ventilation in Tunnels. The Centre has as its most important infrastructure, a tunnel 540 m long, 9,5 m wide and 8,0 m high at centre. This section coupled with ventilation equipment allows the simulation of risk conditions at real scale, which is achieved by modifying the geometry of the section and through two powerful stations situated one at either en of the tunnel. In addition, the Centre houses two test benches for fans and electrical motors at high temperatures. One bench with a re-circulation conduit is the most appropriate for tests in Transversal and Semi-transversal type of installations. The other, is for the testing of electrical motors or fans which operate in zones where the surrounding temperature is high. In this Centre, training has also been developed for Fire Fighters and Civilian Protection Personnel who have to work in fire and smoke rescue conditions in underground structures. Testing conducted at real scale enables this formation and also to improve different computer programmes in the field of Fires and Ventilation.

Jan 1, 2003

By J. W. Neale

Mintek and BacTech have joined forces to provide the metallurgical industry with bacterial-oxidation processes for the treatment of sulphide ores. The processes are aimed at both refractory gold-bearing and base-metal concentrates. Previously, BacTech had commercially implemented the refractory gold process at the Youanmi Gold Mine in Western Australia. More recently, the process has been incorporated in the Sulphide Treatment Plant at the Beaconsfield Gold Mine in Tasmania, Australia. In addition, Mintek and BacTech have recently signed an agreement with the Laizhou Gold Metallurgy Plant in China?s Shandong Province, which will see the third commercial realization of the technology for refractory gold. Development of the base-metal technology is the subject of several papers in the proceedings of this colloquium. The implementation of the refractory gold technology at Beaconsfield is discussed in detail. Some important aspects that are covered include: ?Test work, and the choice of bacterial culture ?Process design choices, and the advantages of the Mintek-BacTech process ?Inoculum build-up ?Plant commissioning ?Plant performance. Besides the Laizhou project, Mintek and BacTech are currently investigating several other commercial prospects for the technology. These include the use of the technology for a gold-copper deposit, where the production of both gold and copper is envisaged.

Jan 1, 2000

By Willem C. A. van Niekerk, David A. Baldwin, Nardus Potgieter, Willie A. Gericke

Authorities that regulate environmental issues pertaining to industrial wastes in South Africa regard landfill disposal as the only effective environmental management option for slag and other inorganic by-products from the ferro-alloy industry. Metallurgical slags are widely utilised in civil engineering and construction applications in other countries in the world and in line with the overall philosophy of conserving mineral and other natural resources, these materials should be assessed for the possibility of resource recovery, recycling, reclamation, direct re-use or alternative uses. This presentation describes a risk-based approach for the assessment of by-products from the ferro-alloy industry for alternative use. Once a by-product from an industrial process has been identified for alternative use, its intended use would be defined, but it will not be possible to control its actual use or misuse in society, nor will it be possible to control its fate during the application life cycle. In the interest of protection of human health and the environment, potential risks associated with the handling and uses of a material throughout its life cycle therefore have to be quantified. The assessment has to include both human health and ecological risks and must cover the entire life cycle of a product, from its production up to its end-of-life disposal. The presentation introduces the concept of tiered risk assessment and demonstrates how this applies in the overall assessment of by-products from metallurgical industry sector for safe use in society.

Jan 1, 2007

By J. D. Bosman

The problems associated with squeezing rock conditions in tunnels are well known and have been extensively investigated in the past. Although squeezing conditions are predominantly found in tunnels developed in weak rock types it has been noted at the No. 6 Shaft of Hartebeestfontein Mine where the host rock consists of hard, brittle quartzites. This paper investigates typical time-dependent deformation mechanisms in the rock at Hartebeestfontein Mine. The paper will focus on observations made in a strike-orientated tunnel that intersected weak quartzite layers, that were sandwiched between two competent quartzite beds. The observed squeezing mechanism is dominated by creep along bedding planes with a soft talcaceous infilling that behaves in a clay-like fashion when saturated in water. Stress-induced deformation processes, some distance into the sidewall of the excavation, force the already fractured periphery of the excavation into the void. A laboratory study of the creep of intact rock and discontinuities collected at this site was conducted to characterize the time-dependent behaviour. The difference in creep rates between the two types of quartzite found at this site is described in the paper. Creep tests performed on the talcaceous infilling material found that its presence allows substantial shear creep along discontinuities. Attempts were also made to simulate the squeezing mechanism observed underground with numerical techniques. Due to the discontinuous nature of the mechanism described above, a viscoplastic displacement discontinuity technique was used as it allowed for the explicit simulation of discontinuity creep. The results of the modelling and how it compared with the observed behaviour are described in the paper. Environmental impact statement The work described in this paper will not cause any new, or contribute to any existing, hazards confronting the environment.

Jan 1, 2000

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l'étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L'étude de champs a démontré l'interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l'influence d'augmenter de dimension de l'excavation. La raideur de piliers overburden, la proportion d'extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d'influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d'un pilier a reçu l'influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L'impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d'interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003

By F. S. Hoseinian, D. Deglon, L. leal Filho, M. Safari, T. C. Souza Pinto

This paper investigates the effect of chemical and physical operational parameters on the reverse flotation of Timbopeba itabirite iron ore in a pilot-scale pneumatic flotation cell. Operational parameters include collector and depressant dosages, feed rate, superficial gas velocity and solids concentration. Results show that increasing collector dosage results in an increase in quartz recovery, particularly for the coarser quartz where recovery increases by nearly 30%. Increasing depressant dosage results in a decrease in both quartz recovery and hematite loss, for the coarser hematite particles. Increasing the feed rate has no effect on quartz recovery or hematite loss, suggesting that the pneumatic flotation cell is not residence time constrained. Increasing the superficial gas velocity results in an increase in quartz recovery to an optimum at a Jg of around 0.6 cm/s after which it decreases significantly, particularly for the coarser particles where recovery decreases by as much as 50%. Decreasing the solids concentration does not affect quartz recovery but results in significant decreases in hematite loss. Here, fine and coarse hematite loss decreases from around 25% to 12% and 10% to 2% respectively. Superficial gas velocity and solids concentration are operating parameters which have the largest effect on the flotation performance of the pneumatic flotation cell. Results suggest that this flotation cell should be operated at relatively low superficial gas velocities and solids concentrations. However, these are pilot-scale findings and would need to be tested at an industrial-scale where different operating conditions may be optimal. Keywords: Operational parameters, reverse froth flotation; entrainment; iron ore

Jan 1, 2020

By N. Barton, E. Quadros

This paper addresses the prediction of groutable joint apertures, grout penetration limitations, and possible grout take volumes per cubic metre of rock, as a result of 5 to 10 MPa pre-injection pressures ahead of tunnels. Joints are obviously opened more than in the preceding Lugeon tests, and many rock mass properties can apparently be improved if stable micro-cement based materials are used. Cet article concerne la prédiction des ouvertures des fractures injectables, les limites de pénétration du coulis et les volumes injectés par mètre cube, d’après les résultats des injections à l’avant tête des tunnels sous pressions de 5 à 10 MPa. Evidemment les joints s’ouvrent plus que dans les essais Lugeon précédents. Maintes propriétés du massif peuvent apparemment être améliorés si l’on emploi des coulis a base de micro-ciment stable. Die Publikation widmet sich der Prognose injizierbarer Kluftöffnungen, Grenzwerte für Injektionsreichweiten und erreichbarer Injektionsvolumen pro Kubikmeter injizierter Fels, durch die Anwendung von 5 bis 10 MPa Vorinjektionsdrücken vor der Tunnelfront.Die Klüfte werden offensichtlich weiter geöffnet als in den vorhergegangenen Lugeon Versuchen und mehrere Felsparameter können durch die Verwendung von stabilisierten Micro-Zement basierten Injektionsmaterialien verbessert werden.

Jan 1, 2003

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008

By N. McEwan

Keywords: refractories, chromite, Marico This paper examines the role of refractory-grade chromite in refractories. The chromite deposit at Verref?s Marico Chrome mine is described. The refractory properties of chromite and their role in basic refractories are described. The properties and metallurgical applications of chrome-containing refractories are described and finally environmental issues associated with chrome-containing refractories are discussed.

Jan 1, 2011

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no.1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc. During the 1st quarter of the year 2007, Chemical Initiatives undertook a study to up rate the sulphuric acid plant output by 10% (i.e. from 500 tpd to 550 tpd).

Jan 1, 2009

By B. van Beek, J. Ndlovu, K. T. Hara, J. M. A. Geldenhuis

This paper describes the development of an alternative technique for measuring the matte level height in sulphide smelting furnaces. The initial studies involved applying electrochemical oxygen probes in a smelting furnace to measure the oxygen potentials of the matte and slag phases. However, these measurements were not successful as a result of low temperatures, preventing there ference electrode from attaining equilibrium during the measurements. These trials were followed up by using oxygen probes containing a (Mo + MoO2) reference electrode instead of the(Cr + Cr2O3) reference electrode used previously. It was shown that with some further development work, it should be possible to measure the oxygen potential of these mattes accurately. Further measurements were performed with a magnetic sensor in sulphide mattes. It was shown that an electronic signal, which is proportional to the magnetic susceptibility of the surrounding material, was generated during immersion into liquid matte. These measurements were extended and done in a smelting furnace. Initial results indicated that when the magnetic sensor was dipped through the slag layer into the matte, a signal was generated as soon as the sensor came in contact with the matte. Measurements are ongoing in order to record (on a computer for improved accuracy) the signal as a function of distance when the sensor is immersed through the slag layer into the matte phase. The magnetic sensor measurements may be the solution to a matte level measurement problem that has existed for a few decades in matte smelting furnaces.

Jan 1, 2004

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020