Search Documents

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By J. Gómez-Hernández, P. K. Kaiser

Abstract The process of stress-induced fracturing around underground excavations in brittle rock is associated with dilation or volume increase of the failed, fractured rock. Different attempts to account analytically for this dilation have been made within the framework of plasticity theory. This theory has been developed mostly for metals, strain-hardening materials or soils, but brittle failure of rock-like materials is characterized by strain-softening behaviour and the volume change is dominated by geometric factors, which may violate stability principles of plasticity. In this work a semi-empirical Rock Mass Bulking Model (RMBM) was developed, using as starting concepts: dilation angle, plastic strain rates, effective deformation modulus, effective Poisson's ratio, Griffith locus, and the definition of a bulking factor BF introduced by Kaiser et al. (1996). The model was calibrated in order to obtain bulking factors that are consistent with experimental data and case studies of measured bulking around underground excavations. Résumé La fracturation provoquée par le stress autour des excavations souterraines dans le minéral friable est associée à la dilatation ou à l’augmentation du volume de la roche en rupture. Dans le cadre de la théorie de la plasticité, différents essais ont été faits dans le but de trouver une justification analytique pour cette dilatation. Cette théorie a d’abord été élaborée pour les métaux, les matériaux ou les sols d’écrouissage, mais la rupture fragile de matériaux d’aspect rocheux est caractérisée par un comportement d’amollissement et le changement de volume est dominé par des facteurs géométriques, ce qui pourrait ne pas être conforme aux principes de stabilité de la plasticité. Dans le présent ouvrage, un Modèle semi-empirique de masse rocheuse a été élaboré, dont les concepts initiaux sont les suivants : angle de dilatation, vitesse de fluage plastique, module effectif de déformation, coefficient effectif de Poisson, locus de Griffith, et la définition d’un facteur de foisonnement FF apportée par Kaiser et al. (1996). Le modèle a été calibré afin d’obtenir des facteurs de foisonnement qui soient conformes aux données expérimentales et aux études de cas sur le foisonnement mesuré autour des excavations souterraines. Kurzfassung Der Prozess von Brüchen in unterirdischen Abgrabungen in sprödem Gestein ist mit der Ausweitung oder der Volumenzunahme des gebrochenen Gesteins verbunden. Verschiedene Versuche im Rahmen der Verformbarkeitstheorie haben versucht, diese Ausweitung analytisch festzustellen. Die Verformbarkeitstheorie wurde hauptsächlich für Metalle, kalthärtende Werkstoffe oder Böden entwickelt, da sprödes Versagen von Gestein ähnlichen Werkstoffen von kaltenhärtendem Materialverhalten gekennzeichtnet ist, und die Volumenveränderung von geometrischen Faktoren beherrscht wird, die die Stabilitätsprinzipien der Plastizität übertreten. In dieser Arbeit wurde ein halbempirisches Rock Mass Bulking Model (RMBM) (Modell für das Aufgehen der Gesteinsmasse), entwickelt, für das die folgenden Anfangsprinzipien benutzt wurden: Ausweitungswinkel, plastische Fliessensätze, wirksames Verformungsmodul, leistungsfähiges Poissons Verhältnis, die Griffith Ortskurve und die Bestimmung eines Aufgehensfaktor BF1 der von Kaiser et al. (1996) eingefürt wurde. Das Modell wurde so kalibriert, dass es die Aufgehenfaktoren erzielte, die mit den Vesuchsangaben und den Fallstudien von Aufgehensmessungen in unterirdischen Abgrabungen übereinstimmen.

Jan 1, 2003

By C. Lemire, A. Biscaro

Ferro-alloys are sold according to the size grading specifications of users. Fines are produced during crushing and the amount produced depends on the crushing process and the physical characteristics of the ferro-alloy. The market value of fines has declined. Market demand is very weak and in some extreme cases is nonexistent. An induction furnace melt process has been developed to solve this problem. The process feasibility has been demonstrated on a small scale with charges of approximately 2.5 kg. The piloting was carried out using a 100 kW furnace with a metal liquid capacity of 140 kg. The operating parameters were determined during the pilot process. The procedures were defined and the equipment required for melting fines produced at the client's site was sized. With the production of ingots, the client can now recover the full value of ferro-alloy fines.

Jan 1, 2004

By Y. F. Bulgakov, Y. V. Melnikova, V. S. Zakharov

A new technology of atmosphere in inertization of fire section with the help of gazeous nitrogen is presented in the report. This technology is based on membrane air subdivision into two streams, concentrated with nitrogen (up to 99%) and with oxygen correspondently with subsequent giving them into the place of fire. This technology belongs to environmentally friendly ones and it has a great number of technical, mobile and economic advantages comparing with the rest of well-known methods of fire extinguishing. This technology application in Ukrainian coal mines allowed to reduce the member of isolated places of fire at the expense of their extinguishing efficiency.

Jan 1, 2003

By Siemag Transplan GmbH

At the Hansa Mine in Dortmund, Germany, coarse run-of-mine coal, up to 60 mm in particle size, has been brought to the surface hydraulically from a depth of 850 m since November 1977. Hoisting is done by a three-chamber pipefeeder, by means of which up to 400 t/h can be lifted. The pipefeeder operates without problems, and has so far shown itself to be efficient and reliable. Vertical hoisting can be carried out by water supplied from the surface, from underground, or from a surface water supply in combination with minewater from underground. Water that flows into the mine, which would in any event have to be pumped to the surface, can be utilized for hoisting operations. The energy costs per ton of coal for a lifting height of 850 m vary between 41 and 62 South African cents, and therefore lie within the range of costs that apply to conventional hoisting.

Jan 1, 1980

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

By D. E. Kraushaar

Ruhrkohle in West Germany evaluates and compares the net present values of long-term periods from its coal mines by a computer assisted long-term planning system. Two main parts of this system are computer programs for the prediction of: (a) mineable reserves and their distribution in longwall panels as a function of dependent geological variables; (b) daily outputs and costs of longwall panels as a function of dependent geo- logical, layout and operational variables. This paper describes the investigations, which ended in the above computer programs: ? the collection of information from past workings and their organization in databases; ? the statistical evaluation of the databases, and ? the resulting correlation formulas. The correlation formulas vary the mean dependent variables as a function of independent variables which can be indicated with high reliability for planning projects in the long run. The system thus serves the purpose of facilitating long-term planning and excluding biased individual judgement of local planning staffs.

Jan 1, 1987

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By R. Strydom, J. H. Selby

Published information is available on the radiological impacts of disposing of zircon sand in a landfill. Zircon flour by virtue of its finer particle size presents a different set of issues during disposal. This paper describes two options for disposal of such fine grained materials – namely incorporation into concrete aggregates and agglomeration by addition of cement. The study considers the radiological exposure of the public from such disposal methods and concludes that these options are viable alternatives for the safe disposal of waste zircon flour. The disposal of zircon into concrete aggregates at a rate of 10 per cent produces a sufficiently low effect to allow such aggregates to be used in building foundations or other such mass concrete applications. The use of cement agglomeration methods will also provide a safe method of landfill disposal provided at least 20 cm of soil cover is included.

Jan 1, 2003

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By C. E. Hales

In an effort to improve efficiencies and reduce costs, AngloGold has embarked on a process to develop and deliver consistent, high quality, tailings based support or construction products to stopes and tunnels on request. A three-phase approach of product conceptualisation, design and delivery has been adopted. To date a substantial amount of laboratory development has taken place with promising results, indicating that the project aims are achievable. Dans un effort pour améliorer le rendement et réduire les coûts, AngloGold s’est embarqué dans une opération qui vise à développer et fournir aux chantiers d’extraction et tunnels, sur demande, des produits de construction ou de support basés sur rejets qui sont réguliers et de haute qualité. Une méthode à trois volets a été adoptée : conception, création et livraison. A ce jour, un développement important en laboratoire s’est produit, avec des résultats pleins de promesses, qui semblent indiquer que les buts du projet peuvent être atteints. In der Bemühung, die Effizienz zu steigern und Kosten zu verringern, hat AngloGold begonnen ein Verfahren zu entwickeln welches auf Anfrage konsistent hochqualitative auf Haufwerk basierender Unterstützung oder Bauprodukte für Abbaustellen und Tunnels entwickelt und liefert Eine Dreiphasenplan zur Produktkonzeptualisierung, Design und Lieferung wurde adoptiert. Bis jetzt hat eine substantielle Anzahl an Laborentwicklung mit vielversprechenden Resultaten stattgefunden und aufgezeigt, daß die Projektziele erreichbar sind.

Jan 1, 2003

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By P. J. Bhonde, R. D. Angal

Conventionally low carbon ferromanganese is manufactured globally by refining high carbon ferromanganese in liquid state. This process is an expensive and lengthy technique. Hence, the present work was undertaken with the objective of understanding the feasibility and kinetics of the solid state refining of ferromanganese. The process involved transformation of carbon rich carbides viz. Mn3C2, Mn7C3 into metal rich carbide i.e. Mn15C4, Mn23C6 by subjecting the alloy powder to a flowing stream of carbon dioxide. Effect of the process governing parameters such as time, temperature, particle size, pressure on the extent of decarburization was studied. Without any loss of manganese in the form of fumes or slag, it was observed that, there was substantial reduction, viz. 65 per cent in the total carbon content, by this technique. Subsequently, the process was investigated to find out the mechanism of carbon removal. Depending upon the temperature and the particle size, it was found that the rate controlling mechanism changes from chemical reaction control to product layer (ash) diffusion control. The activation energy for each of the aforesaid mechanism was computed. The values thus obtained substantiated the aforesaid mechanisms.

Jan 1, 2004

The South African Institute for Mining and Metallurgy celebrated its 95th anniversary with a banquet at The Carlton on Friday, 2nd June, 1989. This event was attended by 600 people, including the Presidents of AS&TS, constituent societies, and other kindred bodies, together with members and their guests. The guest speaker was Mr Muray Hofmeyr, Chairman of the Johannesburg Consolidated Investment Company Limited, who gave an interesting and thought-provoking talk entitled 'Will we still be the best in the year 2001'

Jan 1, 1989

To the trustees of The SAIMM Scholarship Fund We have audited the annual financial statements of The SAIMM Scholarship Fund set out on pages 587 to 592 for the year ended 30 June 2005. These financial statements are the responsibility of the trustees. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with International Standards on Auditing. Those standards require that we plan and perform the audit to obtain reasonable assurance about whether the financial statements are free of material misstatement. An audit includes: examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, assessing the accounting principles used and significant estimates made by management, and evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the trust at 30 June 2005 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice.

Jan 1, 2005

By S. Kauvosaari, M. Olofsson, O. Haavisto, M. Kosonen, J. Martikainen

The target in grinding circuit operation is usually to maximise the throughput and energy efficiency while keeping the product particle size on an optimal level for downstream operations. Furthermore, feed ore variations in size and hardness need to be compensated in order to stabilise the process. This is a challenging task for any circuit and requires good instrumentation, combined with careful control design. This study investigates the control of a two-stage iron ore grinding circuit with an AG and pebble mill at LKAB Kiruna KA3 concentrator in northern Sweden. A new control approach based on multivariable model predictive control (MPC) is designed, implemented and evaluated for the circuit. Additionally, advanced instrumentation including a volumetric charge measurement for grinding mills is utilised. The MPC control approach starts with step tests that are used to model the effect of manipulated variables (MVs) like feed rate, water addition and primary mill speed on controlled variables (CVs) such as final product particle size, power consumption and volumetric charge of the mills. In the control implementation phase, the models are then utilissed together with current process measurements and known operating limits to predict optimal future changes for the manipulated variables in order to reach the desired process output values. It is shown that the new control approach improves the stability of the circuit and reduces energy consumption. Keywords: Model predictive control, grinding, optimisation

Jan 1, 2020

By G. R. W. Walker

A unique means of obtaining sea-water by G. R. W. WALKER, Pr. Eng., B.Sc. (Hons.) (Min. Eng.) (Member) Although the mining and treatment operations at The Consolidated Diamond Mines of South West Africa, Limited, are located within an average distance of I km from the Atlantic Ocean, the supply of clear sea-water in large and continuous quantities for use in treatment plants is made difficult by siltation of water-holes and the amount of sand in suspension in the sea itself. The need for sixty million litres of sea-water per day at the new No. 2 treatment plant necessitated the construction of a system that would ensure a continuous and reliable supply. Several sea-water intake schemes were proposed. This paper outlines the need for an improved means of obtaining water and describes the construction of the scheme eventually chosen - a tunnel driven through bedrock for over 400 m beneath the Atlantic Ocean. At the end of the tunnel, two large chambers were excavated from which vertical holes were drilled to intersect the sea-bed.

Jan 5, 1976

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001