Search Documents

Carbon-concentration Meter The latest of these, the ultrasound-based carbon concentration meter, was developed by Mintek with original sponsorship by the Chamber of Mines Research Organization, and is now being manufactured and marketed worldwide by Debex Electronics in Johannesburg. Testing of detonators* The Chief Mining Engineer has asked the South African Bureau of Standards to monitor locally manufactured, as well as imported, detonators. This could ensure greater safety in fiery mines.

Jan 1, 1990

By L. Archambeault

This paper describes preliminary research on the application of Markov Decision Processes (MDP) to Real Option Valuation (ROV) and the optimisation of mine scheduling. The MDP framework is a novel approach to option valuation and scheduling in mining operations. A learning agent is introduced into the valuation process of an open pit, where prices and block ore grades have probabilistic values. The prices are modelled using a mean reverting diffusion process and the block grades using sequential Gaussian simulation. The agent is asked to learn which production parameters should be used in order to maximise the overall value of the project. The introduction of the agent permits a real option approach to mine valuation, such that the value associated with the robustness of a design to uncertainty can be measured. A simulated example is used in which there are ten blocks to be extracted under conditions of grade and price uncertainty. Using policy iteration, an optimal policy is generated and the value of production options is found. The potential financial gains from applying MDPs to mine valuation and optimisation are substantial and warrant further investigation.

Jan 1, 2007

By L. Cheng, Y. Liu, Z. Shen, H. Shang, Y. Li

The pre-concentration process of magnetic coarse particles can discharge waste rock or liberated gangue before milling, which is an effective means to reduce cost and increase the efficiency of the concentrator, but the weakly magnetic ore doesn’t have the effective separation method of coarse particle such as hematite, limonite, ilmenite and so on, Because the composite iron minerals contain both strong and weak magnetic elements, the pre-concentration process cannot be applied, or the existing pre-concentration process has problems of complicated configuration and high operation cost. By researching a new type of external magnetic separation technology, the pre-concentration process of composite iron ore was realised by single equipment, which can have a good recovery rate with simple arrangement. In this paper, the separation principle and structure characteristics of the external magnetic separator were researched, and the magnetic circuit characteristics of the external magnet were analysed. The laboratory tests of vanadium titanium magnetite were conducted, and the test results proved that the external magnetic separator can be applied for the pre-concentration process. The industrial application shows that a product of TFe 24.76% with 90.08% recovery, TiO2 10.10% with 91.78% recovery can be achieved from the feed of TFe 20.67%, TiO2 8.33%. Keywords: Coarse particle pre-concentration, composite iron ore, external magnet, magnetic separator

Jan 1, 2020

By R. C. Urquhart, W. P. Channon, D. D. Howat

Discussion: The mode of current transfer between electrode and slag in the submBerged-arc furnace by w. P. CHANNON, R. C. URQUHART, and D. D. HOWAT J. MEINTJES I have read the paper with much interest, and I should like to make a few observations. (I) The experimental work deals with resistance heating by an electrode immersed in a slag... AUTHORS' REPLY We thank Mr Meintjes for his critical analysis and helpful comments arising out of his study of our paper. Possibly we should emphasize at the outset that our experiments all related to the conditions in which the lower portion of the electrode was immersed in molten slag. We believe, however,

Jan 12, 1974

By N. Thorp, S. J. Bluhm

It has long been recognized that the provision of an acceptable thermal environment minimizes the danger and the adverse effect of heat stress, which is directly linked to decreased productivity, increased accident rates, and excessive physiological strain in workmen. Refrigeration in one form or another helps to provide this acceptable thermal environment. This paper outlines the problems encountered in a working area, and the steps taken to alleviate environmental conditions in some stopes with the introduction of selective cooling employing small water-chilling units in conjunction with specially designed stope coolers. Performance figures are given for plant and stope coolers, and the effectiveness of the system is assessed from an evaluation of the improvement achieved in the environmental conditions.

Jan 1, 1986

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

By W. K. C. Boemer, G. A. Davies

Vanadium slag production in the shaking ladles started in April 1968, steelmaking was begun in July 1968 and the first continuously cast blocks were produced soon after on the 29th July, 1968. Nominal monthly production of over 20 000 tons was reached in seven months and by December 1970 about 12 000 heats were cast and a monthly production of 35000 tons has been achieved.

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By M. C. van Blerck

Since its introduction in 1956, the capital allowance has been increased and its scope widened. At present the allowance is 10% in respect of two categories of gold mine (post-1973 and other deep level mines) and 6% in respect of natural oil mines. The allowance is a significant incentive encouraging the development of new mines, to the benefit of both the fiscus and the South African economy as a whole. A strong case can be made for increasing the amount and the scope of the allowance. The Margo Report recommendation that the allowance should possibly be replaced with a system of direct grants is, in theory, neutral. However, practical difficulties exist with cash grants and there is concern with the implications elsewhere in the Margo Report that the capital allowance is excessive and that, as a consequence, such direct grants will represent an effective reduction in this incentive. I believe that the best course of action would be the retention (and enhancement) of the capital allowance and the expansion of its scope.

Jan 1, 1988

By P. E. Venteer

The Grootegeluk coal-processing plant treats 3 kt of raw coal per hour to produce a middlings fuel coal and a coking coal fraction with ash contents of 35 and 10 per cent respectively. The plus 0,5 mm fraction is treated by heavy-medium processes, the final top size of the coal being 15 mm. About 400 t of minus 0,5 mm coal per hour is subjected to froth flotation. The routes originally considered for the processing of this fine coal were froth flotation, shaking tables, heavy-medium cyclones, and water only cyclones in combination with froth flotation. The results from tests on the fines arising from a small-trial open-cast mine are discussed. When the froth flotation route was decided upon, further tests were conducted on the selection of the equipment most suited to the particular requirements of this coal and the rest of the plant. Tests using different types of flotation cells and dewatering equipment are discussed. During the commissioning, several operational problems were encountered, and the work done to find the best solutions is discussed.

Jan 1, 1984

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

This paper provides a review of the chemical reactions occurring in the submerged arc processing of chromite ores. The excavations of industrial furnaces have shown that the charge, as it descends through the furnace, passes through a number of distinct reaction zones. Each zone is characterised by differing process conditions and reaction products. The phase equilibria, reaction steps and mechanisms occurring as the charge progresses through the furnace are examined, and the potential influences of these factors on the process outcomes are discussed.

Jan 1, 2004

By D. Francois-Bongarcon

The ?Poisson effect? is defined and characterized. It takes place even when the material to sample is not liberated. Gy, Pitard, Ingamells, and others, including the author, recommend that a minimum average number of particles of mineral of interest characterize the recommended sample size. How many? Recommended numbers range from 6 to 40 particles depending on authors, corresponding to standard deviations of 41% to 16%. Some guidelines are proposed, and the often alleged ?double-Poisson? effect is examined.

Jan 1, 2009

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By E. H. van Niekerk

The production of high-strength Iow-alloy (HSLA) steels containing either niobium or vanadium as the principal micro-alloying element is discussed, including recent developments in steelmaking practice that have had a great effect on the development of HSLA steels; strengthening mechanisms, as well as the principles of thermomechanical treatment during controlled rolling on a hot-strip mill; and the results of production heats with various amounts of micro-alloying elements.

Jan 1, 1984