Search Documents

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

By S. W. Evans, G. Pienaar

Weldable steel plate with a good combination of strength and toughness is currently produced from 0,12 to 0,28 per cent carbon low-alloy steel heat-treated by roller quenching and tempering. Alternatively, steel plate of the same strength can be produced at a lower production cost by the use of very-low-carbon steel (0,03 to 0,08 per cent carbon) processed by in-line quenching without tempering. This paper reports the results of experimental work on these steels, and compares them with the properties of conventional steel. On thinner sections, it was found that the properties of the experimental steels compare favourably with those of conventional grades.

Jan 1, 1989

By M. Buchmann, T. Mütze, F. Heinicke

Dry air classification is a well-known technique used for decades in the cement industry to separate material in the size range of 0.01-1.0 mm. Additionally, in corresponding dry grinding circuits with effective machines such as High Pressure Grinding Rolls (HPGR), the energy consumption can be reduced compared to wet applications. These dry systems are not state of the art in minerals processing plants, but first prototypes have been installed and an increasing number of projects are starting to evaluate this option. One challenge in this field is the mineral composition of ores, which have, by far, a higher variety in density and size than those of cement. High density particles such as iron- containing ones have higher settling rates than low density silica particles of the same size. The main question to answer in this paper is how to evaluate this effect, so a quantitative method using Mineral Liberation Analyses was developed to calculate two-dimensional partition curves. Additional statistical analyses allow for isolation and quantifying the interaction of density and size, enabling engineers to consider this effect for the sizing of process plants. The paper will present the method and selective results for a compounded ore of iron and silica. Keywords: HPGR, air classification, partition curve, MLA

Jan 1, 2020

By G. R. Marchant, B. K. Loveday

A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation. Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression. The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficial.

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

By K. Levin, P. Lloyd

During the commissioning phase, which is usually the most exciting part of a project involving the design and construction of metallurgical plant, the commissioning engineers interact between the client and the project management. The client wants to see whether all the equipment that he has bought and that, in his opinion, has taken far too long to erect will actually work. Project management expects the commissioning people to con¬vince the client that this is the best design ever developed and that never before have time and money been spent so well. The commissioning team has to fulfil these expectations. Commissioning work is a `shirt sleeve' function, with little of the glamour that is normally associated with fields such as engineering and operations. The team usually works in a partially completed plant with more temporary than permanent services and little (if any) office accommodation, normal working hours do not apply, and the demands made on the team change suddenly and dramatically. This article outlines the activities of the commissioning group and the systems used to smooth the commissioning path.

Jan 1, 1981

By J. Svoboda, W. J. C. Venter, R. N. Guest

The use of gravity or magnetic separation followed by upgrading on a shaking table recovered about 25 per cent of the copper and lead minerals, at a combined metal grade of 20 per cent, from the final flotation tailing at the Tsumeb Mine. Magnetic separation recovered the copper minerals more efficiently than the lead minerals; it also recovered finer particles more efficiently than standard gravity separators. However, the grade of the concentrate produced by magnetic separation was not of sufficiently high grade, and further upgrading by gravity separation was necessary. It was decided to install an 'all-gravity' plant, which would have the added advantage of acting as a monitor or 'policeman' on a plant that receives a fairly variable feed.

Jan 1, 1988

Notices STRASZACKERREPORT The Institute has received, for its information, a copy of the following letter, which was addressed to The Federation of Societies of Professional Engineers: REPORT: COMMISSION OF ENQUIRY INTO THE METHODS OF TRAINING FOR UNIVERSITY DEGREES IN ENGINEERING (STRASZACKER REPORT) Geagte Heer, VERSLAG: KOMMISSIE VAN ONDERSOEK NA DIE METODE VAN OPLEIDING VIR UNIVERSITEITSGRADE IN INGENIEURSWESE (STRASZACKERVERSLAG) Second International Symposium on Jet Cutting Technology This symposium, sponsored and organised by BHRA Fluid Engineering, of Cranfield, England, is to be held at St John's College, Cambridge, from 2nd to 4th April, 1974. Competition for student members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Techomin 74 - World Mining Fair The above World Mining Fair, under the sponsorship of the International Committee for the Organization of World Mining Congresses and the Peruvian Government, is to be held in Lima, Peru, from 3rd to 12th November, 1974, to coincide with the 1974 World Mining Congress, which is to be held in Lima. NIM Reports Report No. 1435 The determination of chromium, manganese, iron, cobalt, and nickel by atomicabsorption spectrophotometry using the nitrous oxide-acetylene flame. Report No. 1463 Liq'uidus temperatures and activities of manganese (11) oxide in slags associated with the production of high-carbon ferromanganese alloys. Report No. 1467 The spectral analysis of solutions. 1. The analysis of rare-earth minerals. Report No. 1479 Infrared studies of the adsorption of oleate species on mineral surfaces,with special reference to fluorite. Report No. 1483 The South African manpower requirements in extractive metallurgy. Report No. 1484 Cost estimates for the production of copper wirebars from sulphidic ores. Report No. 1486 Review of the jluoro-chemical industry of the World. Report No. 1490 The adsorption of krypton, nitrogen, and water vapour on sodium oleate. Report No. 1491 Technology and economics of the Olaus kiln under South African conditions. De Beers Report The dry grinding of tungsten carbide/ steel combinations with diamond wheels. Metallurgical Directory The Israel Export Institute has just published the first edition of the Israel Metal Industry Directory, which gives pertinent information relating to the 750 Israeli manufacturers of metal products-addresses, annual turnover, and products- and to consulting engineers and export companies specializing in metal products. Visiting Nuclear Scientist The National Institute for Metallurgy has announced that Professor Vincent P. Guinn, of the University of California, is to spend his sabbatical leave (April to June) working with the Activation Analysis Research Group of the National Institute for Metallurgy.

By D. E. Scheck

A computer-aided blast design consultant system has been developed. The software consists of two modules: one uses theoretical and empirical formulae and procedures to design a blast based on user supplied geological and mechanical data, while the other is an expert system that analyzes blast vibration problems and recommends remedial action using knowledge based rules. The system is currently undergoing field evaluation.

Jan 1, 1987

By D. E. Sweeney

In May of 1980, a mine operated by Belmoral Mines Ltd experienced a failed crown pillar, resulting in the death of eight miners and putting sixteen others in harm?s way. The Ferderber mine was located in the Val d?Or region of the province of Quebec in Canada, and had been under development for 19 months and production for 9 months, since the opening of the portal. The crown pillar separating the 1?7 level from overlying overburden ultimately failed, permitting an estimated 1.5 million cubic feet of liquefied sediment to gain entry into the mine. This paper back-analyses the cave-in by applying decision error theory, in an examination of the organizational culture and the collective decisions contributing to the cave-in disaster. A case will be made for a greater understanding of mining methodology, geomechanics and risk assessment when operating in such challenging geologic conditions. Boundary condition and decision (BCD) analysis will be introduced as an innovative new method for the analysis of mine accidents and incidents. It will also be shown that BCD analysis can be applied to any event in an enterprise for which standards, norms or legislation exists. A cognitive profile will be presented that provides insight into the safety ethos existing within the Ferderber mine organization at the time of the tragedy.

Jan 1, 2007

By T. K. Roy

INFACON XI has no doubt earned the distinction as the first such Congress in India. This prestigious occasion could become a reality of a long cherished dream of the Indian Ferroalloy Producers, consumers and ex-porters. The International Committee of Ferro Alloys (ICFA), South Africa, the august body for organising INFACON, every three years, could be convinced by the Indian Ferro Alloy Producers? Association (IFAPA) to award INFACON (XI) to India. This Congresss, organized by IFAPA, has opened a window for the Ferroalloy Community of India, the up-coming Asian Tiger, to register their strength and weakness to the world forum with the principal objectives of evolving long and short-term optimum road-maps for development. It is to be reckoned that India is poised to be a steel giant by 2020 when it is envisaged that the steel production may reach a level of 120 million tons of which significant proportion has to be in the categories of alloy and special steels, requiring standard and high grade ferroalloys. Keeping the above objective in view, the theme of this Congress has been rightfully designed as ?Innovations in Ferro Alloy Industry.? This Congress has also earned a distinction of more than eighty papers, finally selected for inclusion in the Proceedings. More than 100 internationally and nationally reputed experts in the field of ferroalloys (technology and manufacturing practices as well as world scenario) have been approached for critical review of abstracts and selection for the proceedings. It needs to be mentioned without the cooperation received from ICFA the high standard of INFACON could not have been assured. The papers are suitably grouped under seventeen heads, starting from world situation to production and operation followed by present and future technologies and finally to modelling and simulation. It is a Herculean task to the Technical Committee to fit these papers in proper sequence. The Commit-tee members kept no stone unturned to ensure the cogency with the subject matters and at the same timekeeping the flexibility of interests of the participant, especially in the context of three parallel sessions. The Proceedings containing only refereed papers of high quality, will serve the entire gamut of ferroalloy industry and will also highlight the present status of concerned countries. The areas of attention to make the industries globally competitive and at the same time laying emphasis on the prevailing practices, will help the industry leaders to formulate an appropriate global approach. Following the break-through step, instilled by INFACON XI, the Proceedings will be available both in bound and in searchable electronic CD-ROM format. I, as the Chairman of the Technical Committee would like to express thanks and high appreciation to all the Committee members for their whole hearted efforts in all respects without which it would not have been possible to complete these proceedings in the scheduled time. Technical Committee desires to place on record their gratitude to Organising Committee for their synergic cooperation all through in successfully executing multifarious tasks, associated with such a grand international technical Congress.

Jan 1, 2007

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By R. C. J. Goode, W. S. Rapson, W. R. Lawrie, L. W. P. Van Der Bosch

W. R. Lawrie (Member): As all the Institute members present are aware, the Ninth Commonwealth Mining and Metallurgical Congress was held in Great Britain from 3rd to 24th May, 1969. The Congress opened in London and the first week was devoted to technical sessions. Several receptions and other forms of entertainment were held in the evenings. The Congress was attended by some 1 200 delegates, many of whom were accompanied by their wives. As can be imagined a large organisation was needed to cater for all the whims of these delegates, to arrange accommodation and to provide transport for the technical trips, for the receptions and for the sight-seeing tours. Papers presented at the technical sessions proved of great interest. It was stimulating to hear of the developments taking place in the various branches of mining and metallurgy. The discussions which developed between men from so many different countries were thought provoking, led to new friendships and most of us made valuable contacts for the future. There were 141 papers presented in the one week. They were given in four separate halls with two, three and sometimes four papers coming up for discussion in each of the three sessions per day in each hall. Among the more interesting subjects were those concerning off-shore drilling and the facilities for production of petroleum and natural gas. Beach mining at Consolidated Diamond Mines drew a large audience. Automation, mechanization and other technical developments were well described and we were brought up to date with modern techniques of mineral prospecting. There was general discussion on the future of the mineral industries together with comments on the consumption and price trends of these metals and minerals. The future of uranium, of vital interest to us in South Africa, came in for much debate. During the first week, besides attending the technical sessions and seeing some of the sights of London, we were royally entertained. There was a banquet, attended by some I 400 people, where we were welcomed by Princess Alexandra, a reception by H.M. Government in the Banqueting House, and we were entertained at the House of Lords on a terrace overlooking the bustling and rather muddy river Thames. Then there was the visit to the Glyndebourne Opera. It is only in London that at 3 o&apos;clock of an afternoon, nearly 1 000 people all togged up in dress suits and long dresses and carrying packets of sandwiches for supper could arrive at a station to catch a train, and not even cause a stir of interest or a raised eyebrow! This is the way we travelled 60 miles to the opera from London. Surely there can be no more picturesque or romantic a setting for an opera than this large 400-year old red brick manor house nestling in the green valleys of the unspoilt Sussex countryside. It was a glorious evening and though we returned somewhat late and tired, not one of us would have missed this experience. After the first week in London there was a choice of tours of one week to London and the Home Counties, Cornwall, a Geological tour to Scotland, South Wales, and North England. These were followed by further one week tours to Yorkshire and Lancashire, Scotland, West Country and Midlands, a Geological tour of Wales, and a Mining and Geological tour to Jurassic Iron Mines. We then returned to London for the final session and closing banquet. Post-congress tours were arranged to Europe and to Ireland. It was a wonderful Congress, a great experience, we made many friends and may there be many more congresses! . L. W. P. van den Bosch (Member): Much has already been said in appreciation of the excellent organisation and arrangements made for the delegates who attended this Congress. This report is confined to a brief discussion of the personal impressions gained from the papers presented and the technical visits attended. The papers covered a wide variety of subjects ranging from highly theoretical observations to practical descriptions of operations. There were three main themes, VIZ: 1. The attention given to research and its forceful application to practical operation. 2. A steady development in mechanization and automation leading to savings in manpower. 3. Improvization, modernization and adaptation of exisitng facilities. Thoughts on these themes can best be illustrated by comments on some of the industries visited. COAL The National Coal Board (N.C.B.) has been most progressive and all of us have heard of the Bevercotes Colliery with its completely automatic mining and coal handling equipment. This was not, unfortunately, on show but there is no doubt that this is one of the greatest advances in coal mining leading towards continuous production. Coal in Britain is fighting for its life against oil, North Sea gas, imported gases and nuclear power. Output is dropping, the less efficient collieries are closing down and efficiencies are steadily rising as the following tabulation indicates: In 1931: 1 million men produced 300 million tons of coal In 1947: 0.7 million men produced 230 million tons of coal In 1968: 0.4 million men produced 160 million tons of coal

By P. L. Crouse

"SynopsisFluorine – in the form of hydrofluoric acid, anhydrous hydrogen fluoride, elemental gaseous fluorine, fluoropolymers, volatile inorganic fluorides, and more – has played, and still plays, a major role in the nuclear industry. In order to enrich uranium, the metal has to be in the gaseous state. While more exotic methods are known, the standard and most cost-competitive way of achieving this is by means of uranium hexafluoride (UF6). This compound sublimates at low temperatures, and the vapour is enriched using centrifugal processes. The industrial preparation of uranium hexafluoride requires both elemental fluorine gas and anhydrous hydrogen fluoride (HF). HF is prepared by the reaction of sulphuric acid with fluorspar (CaF2). Fluorine gas in turn is prepared by the electrolysis of HF. Yellowcake is first converted to uranium tetrafluoride (UF4), using HF, after which the compound is treated with fluorine to yield UF6. After enrichment, the UF6 is reduced to UO2 for use in fuel elements in pellet form.South Africa has the largest reserves of fluorspar internationally, and is the third largest producer after Mexico and China. Fluorine technology has many associated difficulties, because of the reactivity of fluorine and the toxicity of HF. The main barriers to entry into the fluorochemical industry are thus the abilities to produce both HF and F2. Both these substances are produced locally, at the industrial scale, at Pelchem SOC Ltd. Should South Africa contemplate developing its own nuclear fuel cycle as part of the awaited new-build nuclear project, it will be imperative to leverage the existing skills with respect to fluorine technology, resident at both Pelchem and Necsa, for this purpose. This paper summarizes the fluorochemical skills developed locally over the past several decades, and suggests strategies for maintaining the technology base and developing it for the next generation of scientists and engineers.IntroductionFluorine chemistry has always had a very close relationship with the nuclear industry. Although the first mention of fluorspar was recorded in the sixteenth century, and the fundamentals had been well-developed by the Second World War, it was only during the Manhattan Project (Banks et al., 1994), when almost unlimited funds were made available for the large-scale industrialization of fluorine and related compounds, that the technology took off. Expertise in both the chemistry and the engineering aspects of fluorine is essential for the design and running of several of the unit processes in the nuclear fuel cycle."

Jan 1, 2015

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The performance of the improved microclimate suit by N. B. STRYDOM M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, B.Sc. (Potch.) (Visitor), and W. H. VAN DERWALT, M.Sc. (Potch.) (Visitor) An assessment has been made of a new improved microclimate jacket when worn by men working for four hours in a hot environment (wet-bulb temperature of 33,9°C and an air speed of 0,4 m/s) and at work rates of 35 Wand 70W. At the lower rate of work in heat, the use of microclimate suits maintained the rectal temperatures of the men at almost the same level as when they worked without that protection at normal room temperature (20°C). At the greater rate of work without protection, the men&apos;s rectal temperatures rose to 40°C within two to three hours, so that they could not complete four hours of work. When they wore microclimate suits, they easily completed four hours of work, and their rectal temperatures were lower than when they worked at the lower rate without protection.

Jan 8, 1975

By E. P. Gush

Diamonds, an enigma in a mineral resource sense. Chemically, diamonds are no more than carbon crystals in a cubic system-formed one might add under conditions of great pressure and temperature. They have certain physical properties which are fairly unique. They are very hard, they have a high refractive index, they luminesce, some of them fluoresce, they have a high specific gravity, they don&apos;t wet and they are a good conductor of heat. In a way, a rather clinical set of qualities. Of course, these qualities are what give diamonds their use and their beauty. It is on the emotional side that they get complex and stir memories of legends, of beauty, of wealth and romance, of war, happiness, bad luck and curses. It is on the emotional side that the value of a diamond is established, if such a thing is possible. Diamonds are extremely varied, there are more than 5000 categories into which they are sorted, so there is room at each point across the spectrum for their individualities to emerge, and accordingly their attractiveness to each buyer is unique.

Jan 1, 1994