Search Documents

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By M. J. Little

Potgietersrust Platinums Ltd is Anglo Platinum?s only open pit operation and annually extracts 57 million tonnes of rock from 2 open pits. Over the past 3 years ~220 km of exploration drilling has been done, ~1000 km of rock face have been exposed for face mapping and over 7000 laboratory and field tests have been conducted. This has produced large amounts of geotechnical data to be utilised for feasibility studies, initial slope design and ongoing slope optimisation. It was necessary therefore to develop geotechnical databases to manage the vast amounts of data collected. SABLE and MineMapper 3D databases were created for logging and mapping respectively, with rock testing data incorporated into both. A pit inspections database was developed in MS Access and the existing groundwater and slope monitoring database was improved. The databases were linked to AutoCAD and Datamine to ensure that the latest geotechnical data is used for planning, draughting and modelling. The use of geotechnical databases ensures that no data is lost, standards are maintained and analysis can be easily performed. This increases the confidence of the analysis and allows the geotechnical engineers to optimise slope designs and blast designs on a regular basis. This reduces the risk of slope failure thus making the open pits more economical and safe.

Jan 1, 2006

By R. E. Phillips, L. A. Cramer, R. T. Jones

Atomaer (Pty) Ltd is a technology-driven company with interests in Western Australian nickel. Atomaer (RSA) Pty Ltd is a process technology company operating in Southern Africa. It is a subsidiary of Atomaer Holdings Pty Limited (Atomaer), which has operating companies in Australia, Africa, South America, and Europe. In addition, Atomaer has substantial shareholdings in Braemore Resources Plc, a nickel company with interests in sulphide nickel projects in Western Australia and Southern Africa listed on the Alternative Investment Market of London Stock Exchange (AIM); Mintails Limited, a gold company with interests in gold operations in South Africa listed on the Australia Stock Exchange; and Brinkley Mining Plc, a uranium company with interests in Southern Africa listed on the AIM. Independence Platinum Limited (IPt) has been formed by Atomaer to undertake the commercial development and exploitation of Mintek's ConRoast technology with the strategic objective of providing independent smelting and refining facilities with lower capital and operating costs for the treatment and processing of platinum concentrates, including those with high chrome and/or nickel and/or low platinum group metal values, for the development of platinum projects by junior resource companies in South Africa. The platinum mines of South Africa have traditionally exploited the Merensky Reef of the Bushveld Complex for platinum production. However, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the ore bodies at deeper levels. In the past decade, all of the platinum producers have begun to mine the UG2 reef because of its cheaper mining costs. UG2 ore usually has lower platinum group metal contents and higher chrome values. The new junior resource companies have gained access primarily to UG2 reefs. Consequently, platinum mining is becoming more UG2-based and the resulting concentrates contain high levels of chromitite. UG2 concentrates are difficult to smelt in the current six-in-line submerged arc furnaces, and this leads to increased capital and operating costs for those smelting operations. The platinum mines of South Africa produce the majority of the world's platinum metal used in automotive catalysts and jewellery. As the platinum market is forecast to grow at a healthy rate into the future, the SA producers Anglo Platinum, Impala, Lonmin, and Northam are planning to expand mining operations in the next decade. Furthermore, a number of smaller new producers who are accessing other mineral resources are entering the buoyant market and will produce platinum concentrates for purchase or toll treatment. Hence, a shortage in both smelting and refining capacities is anticipated. Further smelting and refining facilities independent of the major platinum producers will be required in South Africa by 2010. Mintek's ConRoast technology is best suited to fill the need to treat a high proportion of UG2 concentrates in a cost-effective and technically efficient manner. Atomaer base metals technology has been developed for rapid leaching of nickel and other base metals from alloy. Significant reductions in capital and operating costs are expected from the combination of the two advances in process technology compared with that installed at the existing smelters and refineries that were established over 20 years ago. Independence Platinum will be listed on AIM and the Johannesburg Stock Exchange (JSE) in 2007, and developed as an independent, vertically-integrated platinum company using its independent smelting and base metals refining facilities as a strategic platform to promote the development and mining of platinum projects by junior resource companies in South Africa through technical co-operation, strategic alliances, joint ventures, off-take, toll-refining, and marketing agreements.

Jan 1, 2006

By N. Watson

Historically the insurance industry's involvement in any project has been relatively late in the process. Often it was a case of the last item to be ticked off the checklist has been to ensure that the insurance is in place. However, in more recent times insurers have imposed more restrictions on the cover they are prepared to provide, which has in some cases necessitated a change in the contracting structure to accommodate the insurance policy(ies). In addition, changing contractual practices have changed the allocation of risk between the various parties involved. This calls for a more proactive approach to the design and implementation of an insurance program for both the construction and operational phases of any resource project. This paper explores how a risk managed approach to the design and implementation of an insurance program for a resource project can align itself with current management approaches to project development. From the authors' experience, this approach is best adopted early on in the project (often in conjunction with the bankable feasibility study) and follows AZ/NZS4360 to objectively examine and compare a wide range of risk exposures of the project in a time-effective manner across the following areas: ? personnel; ? environment; ? general management; ? compliance - legislation, systems, protocols; ? asset management; ? change management; ? financial impacts to the organisation; ? products/services; ? service delivery; and ? technology. Having identified and then analysed the risk exposures according to common consequence and likelihood ratings the next step is to develop a risk map of all considered exposures. The true value of this approach lies in the development and implementation of a risk treatment plan for identified exposures where the exposure is unacceptable. The plans will lead to the optimal solution to the appropriate risk prevention, risk mitigation and risk transfer options available. This paper also examines other benefits to the project that may arise from adopting a risk managed approach in addition to the ability to design an insurance program which recognises the exposures and the ability of the organisation (and other project parties) to retain risk.

Jan 1, 2007

By P. J. Foster

This paper summarizes a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialed at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this, a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By M. R. Khalesi, Y. Kianinia, A. Seyedhakimi, F. Soltani

"The feed ore to Agh-Darreh gold processing plant (Takab City, Iran) contains 2 ppm Au, 7 ppm Ag, and 120 ppm Hg. After cyanide leaching of the feed at pH 10.4, 80% of the total mercury (in the form of cinnabar and metacinnabar) goes to the tailings dam. In this research, separation of mercury from the tailings by flotation was investigated. The effects of collector type and dosage, pH, and the number of cleaner stages were studied. The results showed that after two stages of cleaning a 40–62% recovery of Hg at a grade of 14.3% Hg is attainable. Recycle water from a test in which 50 g/t amyl xanthate and 30 g/t pine oil was used in the flotation stage showed no adverse effect on the leaching and adsorption of gold onto activated carbon.IntroductionMercury, most commonly found in the nature as the mineral cinnabar (HgS), is a hazardous substance because of its mobility and toxicity (Kyle et al., 2012). Roasting is the wellestablished treatment method for mercury ores, in which the sulphur is burned and volatilized and mercury recovered subsequently by cooling and condensation. However, for low-grade ores, flotation is mainly applied for primary concentration due to its comparatively low costs, low environmental hazards, and flexibility regarding feed variations (Bulatovic, 2007). Particularly, cinnabar can be easily recovered by flotation using pine oil and a collector such as xanthate (Bulatovic, 2007; Crozier, 1991). Floatability of cinnabar is reduced due to surface oxidation when it is exposed to the atmosphere after crushing. This problem can be eliminated by adding copper sulphate and lead nitrate or acetate. The best pH for cinnabar flotation is in the range of 6.5 to 8.5 according to Erspamer and Wells, (1954), who reported that cinnabar and stibnite can be floated with long-chain xanthate collectors and an alcohol frother, with cumulative recoveries of 97.8% and 94.7%, respectively. Lead acetate was used as an activator."

Jan 1, 2017

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By C. Birch

"Mineral reserve statements as well as optimizing mine planning require a block model with grades for each mining block. A cut-off grade is determined by considering the mining costs as well as the expected revenue for each block. These grades are estimated using various techniques, but in reality there is uncertainty in the grade values. These uncertainties result in two types of error. A type I error is where material is classified as ore and mined, but the true value is below the cut-off grade and the material is therefore waste. This material constitutes dilution. The type II error is where material is estimated to be below the cut-off grade and is classified as waste, whereas the true grade is actually above the cut-off grade. This material is not mined and the value is lost.This research considers the value of the lost ore and the costs of dilution under various degrees of uncertainty. Simulation using @Risk and mixed integer linear programing (Excel Solver) is used in a financial optimizer model to maximize either profit or net present value. This is applied to four Witwatersrand tabular gold deposits to investigate the impact of block grade uncertainty on cut-off grades.When optimizing for profit, value may be added by adjusting the cutoff grade slightly downwards. When optimizing for NPV, value may be added by lowering the cut-off grade significantly for the lower discounting rates. At higher discount rates, the lowering of the cut-off grades should be reduced, and in some cases an increase in cut-off grade may be required. Each mine reacted differently to the optimization and thus there is no single rule that can be applied across all tabular Witwatersrand gold deposits."

Jan 1, 2017

International Solvent Extraction Conference 1971 ISEC '71, which will be held in The Hague, The Netherlands, from 18th to 23rd April, 1971, is being sponsored by the Society of Chemical Industry in association with the Koninklijk Instituut van Ingenieurs, the Institution of Chemical Engineers and the Koninklijke Nederlandse Chemische Vereniging. The Working Party on Distillation, Absorption and Extraction of the European Federation of Chemical Engineering is participating in the Conference, which is the 101st event of the Federation. The scope of the Conference covers the entire science and technology of liquid-liquid extraction as applied in all branches of industry. Thus sessions will cover both chemical and chemical engineering aspects of the subject as applied to both inorganic and organic solutes. The conference aims to bring together academic and industrial workers in the field from all parts of the world. The programme includes over 100 papers by authors in 26 countries. Full details of the papers, together with registration forms, are contained in a detailed programme, copies of which are now available from: ISEC '71, 14 Belgrave Square, London, S.W.1, U.K. Department of Mining and Mineral Technology of the Royal School of Mines Postgraduate Courses Technical and economic challenges facing the minerals industry, together with progressive change in methods and equipment, increasingly necessitate re-training of experienced professional engineers who aim for top places. In order to meet this need, this Department has for some years run one year M.Sc. courses. Engineers, often sponsored by their employers, have a choice of three courses which are respectively devoted to mining, applied rock mechanics or mineral process design. The course in Mining is divided into five subjects, which are treated from the business management point of view. It is intended to provide middle management with a knowledge of those techniques that are required by the mining engineering function in the preparation of modern projects. The course in Mineral Process Design provides a systematic use of mineral sciences, engineering and economics for ore testing and process design, so as best to balance the technical and financial requirements for specific mineral resources. The course in Engineering Rock Mechanics is designed to provide a specialized training in the engineering applications of rock mechanics for engineers and geologists, so that they are equipped to treat a wide variety of problems in mining and civil engineering. Prerequisite qualifications are a good first degree in a related subject, plus industrial experience: The rewards include an M.Sc. of the University of London and the Diploma of the Imperial College (DIC). The limited number of places available (12 in each group) makes early application advisable. Full details are available from the Registrar, Imperial College, London, S.W.7.

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By A. Koursaris, J. B. See

An investigation is described in which the resistivities of Mamatwan manganese ore, Delmas coal, and Iscor coke, at temperatures or up to 1400°C were determined, as well as the resistivities of mixtures of ore of a constant size range with Delmas coal or Iscor coke of three different size ranges. The resistivities of the ore and the coal were characteristic of those for semi-conducting materials, were strongly influenced by temperature, and decreased by several orders of magnitude between room temperature and IOOO°C. The resistivity of the coke changed only slightly between room temperature and 1400°C, and the resistivity of the coal approached that of the coke at I300°C. This provides support for the theory that the resistivity of carbonaceous reducing agents is primarily a function of heat treatment, and not of the rank and composition of the coal. Above 1200°C, the resistivity of mixtures of ore and coke fell steeply owing to an increase in the volume fraction of coke in the mixture and to the formation of slag. The results were similar for the three different size ranges of coke. The extremely high resistivities of ore-coke and ore-coal mixtures at Iow temperatures indicate that there is unlikely to be much conduction of current in the higher regions of a furnace. Thus, the resistance of a furnace is governed mainly by the conditions at the electrode tips and in the molten regions. To explain the very Iow resistances of furnaces, usually, about I m£?, it would be necessary for investigations to be conducted under conditions similar to those in the active zone of a furnace.

Jan 1, 1980

By D. D. Aksenova, V. A. Ignatkina, L. A. Samatova, A. V. Lygach, E. D. Shepeta

Calcium minerals such as scheelite, phosphate, apatite are valuable minerals, which have similar flotation properties to the calcium gangue minerals. An additional problem is the fine dispersion and close mineral association of valuable and other minerals. Low polar compounds (non-ionic surfactant), such as fatty iso alcohols, neonol and phosphol, and their combinations with sodium oleate have been studied using flotation of monominerals and ore flotation; ATR IR spectroscopy and TEM for study surface of minerals; UV spectroscopy for control solubility, aggregation and de-aggregation processes. Increase in solubility of fatty acid collectors was confirmed by low soluble (heteropolar) compounds. Oxyethylated esters of phosphoric acid are adsorbed on phosphorite by -O2PO2R2 and on other rock minerals by donation of OH bond. Same effect shows difference of adsorption of fatty iso alcohols on calcite and scheelite. The different forms of adsorption of ionic and nonionic compound on a sparingly-soluble mineral surface creates distinction of the flotation kinetics and technological balance of ore flotation. The results of the separation of flotation of scheelite from calcite depend on the order of pouring into pulp of fatty iso alcohols and oleate, and their ratio in the mixture. Increasing scheelite recovery into rougher scheelite concentrate by 3.6% for both the flotation and sludge classes was obtained. Calcite recovery varied slightly upwards or downwards by 0.8-2.4%. The use of the non-ionic surfactant phosphol in combination with a fatty acid soap allows for obtaining a phosphate concentrate with more than 28% P2O5 content and almost 80% recovery in flotation operation. It is not obtainable with other reagent regimes. Keywords: Flotation, calcium minerals, oleate, fatty isoalcols, neonol, oxyethylated esters, adsorption

Jan 1, 2020

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

By J. R. Dixon

Gold mining has been undertaken in South Africa for more than a century. A great proportion of that mining has been from the Witwatersrand Basin; a geological phenomenon that has few parallels throughout the world. It has produced some 47 000 tonnes of gold mainly from underground mines, many of which have been truly world class gold mines. The gold mines of the Witwatersrand Basin have dominated world gold production from their inception and their production has been one of the cornerstones of the development of South Africa as a whole. The mines have some very specific characteristics; their sheer size, the depth of extraction, the nature of the orebodies, and their labour-intensive methods. The mines have also been part of the Mining House concept-a concept unique to South Africa. South African production has declined from a maximum of 1000 tonnes in 1970 to 470 tonnes in 1997. This, as a percentage of western world production, has declined from a maximum of 79 per cent (in 1970) to 21 per cent of world production (in 1997). The nineties' have seen South Africa and its mining companies move onto the world stage and face the harsh realities of having to compete in all spheres of business with their aggressive counterparts principally in Australia, Canada and the USA. The fight is for investment funds with the owners looking for the best returns on their money. In his address Roger Dixon will examine the current situation in the gold mining industry and examine the competitiveness of the mines of the Witwatersrand Basin compared with their peers worldwide. He will also discuss some of the fundamental challenges facing South African gold mines in the areas of legislation, technology, industrial relations, and health and safety. The environment in which the mines operate has changed radically in recent years and their ability to respond to these challenges will determine their future existence.

Jan 1, 1998

By S. J. Moema, M. G. Maruma, L. A. Mampuru, M. E. Maja

"The most commonly used high-chromium white cast iron (HCWCI) is the hypoeutectic white cast iron that contains 2–3.5 wt.% C and 10–30% Cr. This type of material relies on hard, brittle M7C3 carbides to impart good wear resistance. Due to its good wear resistance, this material has found application in the mining industry and cement industry. However, it has low fracture strength and this challenge led to research aimed at refining the microstructure. This was done by the addition of niobium in the range between 0.1 and 0.6 wt.%. In the as-cast condition, the addition of niobium was found to increase the fracture strength due to the finer eutectic microstructure. The hardness was also found to have increased slightly compared to the reference alloy with no niobium additions. Low fracture strength after heat treatment was observed in the Nb-added HCWCI, which is believed to have been caused by the precipitation of secondary carbides and the transformation of the matrix from austenite to martensitic. IntroductionFor the past few years Mintek has been involved in a project in which a number of alloys have been identified for grinding media applications. The high-chromium white cast iron (HCWCI) alloys were among the alloys researched for this application. The knowledge acquired from the grinding ball media research has now been extended to mill liners, which have traditionally been made of manganese-, chromium- and chrome-molybdenum steels. The replacement of worn mill liners costs the mining industry a significant amount of money and this has led to a need for continuous research to prolong the life of the liners. During milling operations, liner wear has an adverse effect on the capacity of the mill, the energy efficiency and milling efficiency and finally leads to relining, to replace worn liners."

Jan 1, 2016

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

By J. A. Venter, M. K. G. Vermaak, J. G. Bruwer

Electrostatic separation is employed in the concentration of zircon and rutile. The zircon concentrate undergoes an acid treatment to remove impurities from the surface of both the zircon and rutile. The purpose of the acid treatment is to increase the difference in the resistivities of the two minerals, thus ensuring the best possible electrostatic separation efficiencies. Previous test work suggested that these impurities are not removed, but only modified; the surface modification seemed more prevalent in the case of the rutile. The resistivity of the rutile changes with pH and thus the electrostatic separation of the rutile is influenced. X-ray photoelectron spectroscopy (XPS) indicates that there is an increase in the OH and adsorbed H2O concentrations on the rutile surface. XPS also showed significant differential charging on the rutile surface, which indicates that the species on the rutile surface have different resistivities. The zircon particles from the conducting and non-conducting streams have similar resistivities and no major differences in their surface species. Zircon losses during the final electrostatic separation appear not to be due to surface effects, but due to shielding of particles during the separation.

Jan 1, 2007

Knelson concentrators are commonly used to recover fine liberated gold in gold processing plants. The decision to employ a gravity gold circuit consisting of centrifugal devices such as Knelsons is primarily taken on the results of GRG tests, among other considerations. While the GRG test is considered a material characterisation test, which is useful in the design stages, its use in evaluating the performance of an existing unit is questionable. The problem is exacerbated by the fact that it is time consuming and costly. This paper examines the validity of the GRG test for performance evaluation and discusses alternative test work that can be performed to evaluate the performance characteristics of an operating machine. Principles that are useful in selecting optimal operating parameters, such as optimal fluidising water flow rate for a given ore/machine combination, are also discussed and illustrated with laboratory and plant data.

Jan 1, 2007