Search Documents

Ground control problems in the form of large dome or wedge collapses have been experienced at Tau Lekoa Mine since production began. Crush pillars in various configurations have been used and through a process of trial and error the current pillar layout has been derived. A strike pillar layout is used and additional mid-panel pillars are left spaced a maximum of 10m or 16m apart, depending on conditions and mining direction. Pillar spacing is based on an empirical relationship between fallout height and pillar spans. Analysis of the spatial distribution of large falls of ground indicates that there may be several geotechnical relationships contributing to stable pillar spans. The current focus is to define the relationship between geotechnical areas and hangingwall stability so that area specific support strategies can be formulated that could result in increased production efficiencies. Depuis le début de la production, la mine Tau Lekoa a connu des problèmes de contrôle au sol, sous la forme d’effondrements de grands dômes ou coins. Des piliers d’écrasement, dans des configurations variées, ont été utilisés et une série d’essais a résulté en la disposition de piliers en cours. Une configuration de piliers de direction est utilisée, et des piliers mi-panneau supplémentaires sont laissés, espacés d’un maximum de 10m ou 16m, selon les conditions et la direction de la mine. L’espacement des piliers est établi sur une relation empirique entre la hauteur des retombées et les intervalles entre piliers. L’analyse de la distribution spatiale de grandes tombées de terrain indique qu’il peut y avoir plusieurs relations géotechniques qui contribuent à des intervalles de piliers stables. L’intérêt présent est de définir la relation entre les zones géotechniques et la stabilité du toit, pour pouvoir formuler des stratégies de support spécifiques à un endroit, ce qui entraînerait des accroissements de production. Bodenkontrollprobleme traten seit Produktionsbeginn in Form von grossen Keil oder Dachhaubenbrüchen in der Tau Lekoa Mine auf. Bruchpfeiler in verschiedensten Konfigurationen wurden verwendet und auf Grund empirischer Fakten wurde das gegenwärtige Pfeilerlayout abgeleitet. Ein Layout für Strukturpfeiler wird verwendet und zusätzliche mittig situierte Pfeiler in einem Maximalabstand von 10m bis 16m installiert, abhängig von den Konditionen und der Vortriebsrichtung.Der Pfeilerabstand basiert auf dem empirischen Verhältnis Fallhöhe und Pfeilerspannweite. Die Analyse der räumlichen Verteilung großer Bodenabsenkungen deutet an, daß es einige geotechnische Verhältnisse geben kann, die zu stabilen Pfostenspannweiten beitragen. Der gegenwärtige Fokus soll das Verhältnis zwischen geotechnischen Bereichen und Stollendeckenstabilität definieren, damit bereichspezifische Unterstützungsstrategien formuliert werden können, welche in erhöhter Produktionsleistung resultieren könnten.

Jan 1, 2003

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

By P. den Hoed, J. Nell

Tests were conducted on samples of rutile, titaniferous slag and ilmenite; each sample was mixed with coke and chlorinated in a bubbling fluidized bed at 1000°C. Profiles of the rates of chlorination of species were constructed from chemical compositions of the bed residues at different durations. From the start FeO and MnO are chlorinated quickly and all but entirely in a fraction of the time it takes to chlorinate all the TiO2. When the level of FeO is significant, as in slag and ilmenite, FeO is chlorinated faster than TiO2is. In these oxides, there is an inverse relationship between the rates of chlorination of FeO and TiO2during this first stage; the relationship, moreover, correlates linearly with the initial percentage of FeO in the oxide. We identify three stages in the chlorination process; a first, in slag and ilmenite, when FeO is being chlorinated; a second, when TiO2is most readily chlorinated; and a third, towards the end, when the levels of TiO2are reduced to those of other species. The rates at which individual species are chlorinated are analysed in terms of their appreciation or depreciation with respect toTiO2

Jan 1, 2003

Professor G.T. van Rooyen has guided the Department of Materials Science and Metallurgical Engineering at the University of Pretoria in South Africa for the past 32 years. During this period, 54 masters' degrees have been awarded in the Department, and 17 doctorandi promoted. He has also made a major contribution to industry by his incisive analysis, relevant and practical synthesis, and his exceptional talent in innovative design. He is still active in fracture analysis, thermal fatigue, weld simulation transformation kinetics, and fracture mechanics, and continues to contribute to a better understanding of metallurgical problems encountered in practice. He has advised many companies, and has received many honours and recognitions.

Jan 1, 1994

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l'Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l'index RMR ont été exigés. SRC et des index RMR et d'autres données geomechanical appropriées ont été obtenu pendant l'enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d'accent) in situ, l'analyse de structures tectoniques et des problèmes d'instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l'état de stress(d'accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d'appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l'index RMR.

Jan 1, 2003

By A. M. Clegg

In general, overall experience has shown that the approach to the appointment of a project manager is given much attention, but little specific attention is given first to the risk associated with the project conceptual design and its overall executability within either the new legislative framework or the sustainability of the outcome. The risk in project executability and sustainability within the ?new age? legislative framework of the Mining Charter, etc, is itself however, of far greater importance. The degree of importance being defined by the intended projects impact on the business going forward. This is particularly the case where the intention of the implementation is effectively to turn around or even enhance a loss-making strategic investment like a mine or process plant operation in an ?old-order rights? or Brownfield?s operation. This paper attempts to highlight the importance of a ?pre-project project? (PPP) to mitigate the risk in the ?new age?, with specific reference to operational due diligence (ODD) and project conceptual design.

Jan 1, 2005

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

By K. S. Rao, R. P. Tiwari, V. K. Shrivastava

ABSRACT: In this paper numerical simulation of jointed block mass behaviour obtained in an experimental study has been presented. Singh et al. (2002) conducted extensive tests on the jointed model materials with several joint configurations. The results of this experimental study were used to validate the strength behaviour of numerical block mass model developed using professionally available software. This software basically contains different kinds of material models. From the results of numerical simulation the existence of strength anisotropy was observed. The strength anisotropy so obtained has been compared with the experimental values reported by Singh et al. (2002). The anisotropic curves in both cases are U-shaped with flat base. They show good agreement in sliding mode of failure zone in which inclination ß (= 90° - ?) of joint set-I lie between 20° to 40° for all cases of interlocking. ZUSAMMENFASSUNG: In dieser numerischen Papiersimulation des verbundenen Blockmasse Verhaltens, das in einer experimentellen Studie erhalten wird, ist dargestellt worden. Singh et al. (2002) leiteten umfangreiche Tests auf den verbundenen vorbildlichen Materialien mit einigen gemeinsamen Konfigurationen. Die Resultate dieser experimentellen Studie wurden verwendet, um das Stärke Verhalten des numerischen Blockmasse Modells zu validieren, das mit professionell vorhandener Software entwickelt wurde. Diese Software enthält im Allgemeinen unterschiedliche Arten der materiellen Modelle. Von den Resultaten der numerischen Simulation wurde das Bestehen von Stärke Anisotrophie beobachtet. Die Stärke Anisotrophie also erreicht ist mit den experimentellen Werten verglichen worden, die von Singh et al. (2002) berichtet werden. Die anisotropen Kurven in beiden Fällen sind mit flacher Unterseite u-förmig. Sie zeigen gute Vereinbarung in gleitender Erscheinungsform des Ausfalls Zone, in der Neigung ß (= 90° - ?) von der Verbindung stellenSie Lüge zwischen 20° auf 40° für alle Fälle vom Ineinandergreifen ein. RESUME: Dans cette simulation numérique de papier du comportement joint de la masse de bloc obtenu en étude expérimentale a été présenté. Singh et autres (2002) ont effectué les essais étendus sur les matériaux modèles joints avec plusieurs configurations communes. Les résultats de cette étude expérimentale ont été employés pour valider le comportement de résistance du modèle numérique de la masse de bloc développé en utilisant le logiciel professionnellement disponible. Ce logiciel contient fondamentalement différents genres de modèles matériels. Des résultats de la simulation numérique on a observé l'existence de l'anisotropie de force. L'anisotropie de force ainsi obtenu a été comparée aux valeurs expérimentales rapportées par Singh et autres (2002). Les courbes anisotropes dans les deux cas sont en U avec la base plate. Elles montrent la bonne concordance dans le mode coulissant de la zone d'échec en lequel la inclination ß (= 90° - ?) du joint placez-Je le mensonge entre 20° à 40° pour tous les cas d'enclencher.

Jan 1, 2003

By G. B. Quaye

The deep level gold mining environment is characterized by high stresses that give rise to intense mining induced fracturing of the rock mass surrounding the stopes. In a geologically disturbed region where the intensity of mining induced stress fracturing is high, the degree of faulting and/or the frequency of other geological features such as joints may pose serious strata control problems. Unfavourable intersection of these discontinuities namely, faults, joints and mining induced stress fractures tend to divide the immediate hangingwall into unstable keyblocks which, if not supported, may result in extensive falls of ground. Effective support strategies therefore demand detailed investigation of the predominant inclinations and orientations of these discontinuities. The orientations and inclinations of these discontinuities surrounding a deep level stope have been measured. The results are projected onto the lower hemisphere of a stereographic net to determine the factors that contribute to the falls of ground in the stope. The analyses reveal that unfavourable intersection of these discontinuities divides the immediate hangingwall into unstable wedges that may become dislodged between support units.

Jan 1, 1998

By F. M. C. C. Vieira

The DEEPMINE Research Programme sought to develop the technology and competence to mine gold safely and profitably at depths of 3 to 5 km. Among the many issues addressed was the stability and support of rockpasses at ultra-depth. It was found that high virgin and mining-induced stresses could cause the walls of rockpasses to spall, leading to the deterioration and failure. A comprehensive programme of numerical modelling was conducted to investigate alternative mining layouts and sequences to ameliorate the problem.

Jan 1, 2005

By B. Haimson

A new loading apparatus was fabricated and used to conduct true-triaxial compression tests on KTB amphibolite, a crystalline basement rock. Tests in dry jacketed samples reveal that the intermediate principal stress has a significant effect on the onset of dilatancy and on rock strength, contrary to the implicit assumption made by Mohr-type failure criteria. Failure is induced through a shear fracture that dips steeply in the direction of the least principal stress. Experimental results lead to a new generalized strength criterion in terms of all three principal stresses. Unjacketed KTB amphibolite specimens, exposed to confining fluid, are considerably weaker than the jacketed ones, despite the negligible porosity and permeability. Failure is facilitated by several closely spaced subparallel tensile cracks normal to the least stress direction. SEM analysis suggests that microcracks developed upon dilatancy onset are penetrated and extended by the confining fluid, bringing about the unexpected rock failure mechanism at reduced stress levels. Un nouveau dispositif à chargement fut fabriqué et utilisé afin de réaliser un vrai essai de compression tri-axial sur KTB amphibolite, une roche cristalline du sous-sol. Les essais effectués sur échantillons enveloppés et secs révèlent que les contraintes principales intermédiaires affectent considérablement le début de la dilatance et la résistance de la roche, contrairement à la supposition fondée sur le critère de rupture de Mohr. La rupture est produite grâce à une cassure de cisaillement très incliner en direction où la contrainte principale est moindre. Ces résultats expérimentaux indiquent un nouveau critère de rupture général en fonction des trois contraintes principales. Les échantillons de KTB amphibolites sans enveloppe, exposés à un liquide confiné, sont considérablement plus faibles que ceux enveloppés, malgré la porosité et la perméabilité négligeable. La rupture est facilitée par plusieurs fissures de traction adjacentes et sub-parallèles, normales à la plus petite contrainte principale. L’analyse SEM suggère que les micro-fissures développent suivant le début de la dilatance, elles sont pénétrées et agrandies par le liquide confiné, produisant un mécanisme de rupture de roche inattendu, ceci à un niveau de contrainte réduit. Ein neuer Ladungsapparat wurde hergestellt um real - triaxiale Druckfestigkeitsversuche in KTB Amphibolit, einem kristallinen Grundgebirgsgestein, durchzuführen. Messungen in trockenen, bedeckten Proben zeigen that die mittlere Hauptspannung eine bedeutende Wirkung auf das Einsetzen von Dilatanz und auf die Stärke des Gesteins hat, im Gegensatz zu der impliciten Annahme auf Grund von Mohr-ähnlichen Versagungskriterien. Versagen ist induziert durch eine Scherfraktur die sich steil in die Richtung der geringsten Haupspannung nach unten senkt. Messergebnisse führen zu einem neuen, verallgemeinerten Stärke Kriterium dass auf alle drei Hauptspannungen basiert ist. Unbedeckte KTB Amphibolit Proben, die unmittelbar den umgebenden Fluiden ausgesetzt sind, sind wesentlich schwächer als bedeckte, trotz geringfügiger Permeabilität und Porosität. Versagen wird gefördert durch mehrere, nebeneinander liegende, sub-parallele Spannungsbrüche, normal zu der geringsten Spannungsrichtung. SEM Analyse lässt vermuten dass Mikrobrüche, die sich beim Überschreiten der Dilatanzschwelle entwickeln, durch die umgebenden Fluiden fortgepflanzt und weiter verbreitet werden, und unerwartet, auf Grund der reduzierten Spannungswerte, den Versagungsmechanismus des Gesteins einleiten

Jan 1, 2003

1. New books 1979 Louisville Coal Conference proceedings. Epping (England), Bowker Publishing Co., 1980. 4 vols. $43.00. Proceedings of a joint meeting of the Institution of Mining and Metallurgy, the Society of Mining Engineers of AIME, and the Metallurgical Society of AIME, held in London, 27 to 30 May, 1980, by M. J. Jones (ed.). London, Institution of Mining and Metallurgy, 1981. 350 pp. £46. Economic mineral deposits, by M. L. Jensen and A. M. Bateman. 3rd ed. New York, John Wiley, 1981. 752 pp. $22.95. E & MJ intErnational directory of mining and mineral processing operations. Epping (England), Bowker Publishing Co., 1980. 1314 pp. $67.00. Physical methods in modern chemical analysis, by T. Kuwana (ed.). New York, Academic Press, 1980. Vol. 2. 432 pp. $38.25. English translations of DIN standards. Availablefrom the SABS, Private Bag 191, Pretoria 0001. Mining international year book. London, Financial Times, 1981. 730 pp. $90.00 airmail, £37.50 surface. Analytical atomic absorption spectroscopy. Selected methods, by J. V. van Loon. New York, Academic Press, 1980. 360 pp. $35.00. 2. NIM reports Report no. 1848 An electrochemical and kinetic investigation of the behaviour of gold in chloride solutions. I. The cathodic deposition of gold. (First issued 7th Jul., 1976.) Report no. 1844 An electrochemical and kinetic investigation of the behaviour of gold in chloride solutions. 11. The anodic dissolution of gold. (First issued 7th Jul., 1976.) Report no. 1846 An electrochemical and kinetic investigation of the behaviour of gold in chloride solutions. 111. The gold(II1)- gold(I) eaction on platinum and the disproportionation of gold(I). (First issued 7th Jul., 1976.) Report no. 1979 An electrochemical investigation of the behaviour of gold in chloride solutions. I V. Results obtained from Phase 2 of the investigation. (First issued 30th Jun., 1978.) Report no. 2093 The measurement of electrical variables in a submergedarc furnace. Steels for pipelines Since welding was first introduced as a method of joining pipelines, gas-pipeline engineers have taken the opportunity to increase gas pressures, and hence increase the efficiency and economy of transporting gases. Envitec '83 The International Trade Fair and Congress for Engineering in Environmental Protection - the ENVITEC '83 - will take place in Diisseldorf from 21st to 25th February, 1983.

Jan 1, 1981

By J. M. Font, R. G. Reddy

Jan 1, 2004

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972