Search Documents

By V. J. Moore

Introduction Although months have passed since APCOM 87, held from 19th to 23rd September, 1987, the vivid memories of all aspects of its activities remain as clear in one's mind as if it all happened only yesterday. The Symposium, which was held at the Johannesburg Sun Hotel, was organized by The South African Institute of Mining and Metallurgy in collaboration with the Council for Mineral Technology (Mintek), supported by The Geostatistical Association of South Africa, The Operations Research Society of South Africa, and the Computer Society of South Africa, and was backed financially by the Chamber of Mines of South Africa. The total number of registrants amounted to 375 delegates and 50 affiliates: 100 of the delegates were from outside the Republic of South Africa and represented 15 countries, namely Australia, Brazil, Canada, Chile, France, Great Britain, Greece, Italy, Namibia, Phillipines, Sweden, Turkey, United States of America, West Germany, and Zimbabwe.

Jan 1, 1988

It is a great honour to officiate at the celebration of the centenary of the South African Institute of Mining and Metalurgy. Tonight's festivities bring back happy memories of my association with South Africa's mining industry during my tenure of office as Minister of Mineral and Energy Affairs. They also remind me of the illustrious personalities who have preceded me on this podium. The Pioneers They include Sir Percy Fitzpatrick, who spoke in 1909 on the eve of the Union, General Smuts, and, on many occasions during the 1920s and 1930, Jan H. Hofmeyr. The basic issues addressed by them continue to enjoy the Institute's attention today, namely the optimal and safe exploitation of our country's mineral resources and cost-effective extraction of minerals from their ores. Translated into the Institute's key objective it reads: To initiate and give effect to the means whereby the requirements for technology and scientific knowledge if the minerals and metals section if the South African economy is satisfied.

Jan 1, 1994

By J. C. Zachariades, D. M. Fraser

The leaching of pyrolusite in acidic ferous sulphate solution was studied so that the important factors governing the kinetics of the reaction could be determined. The reaction is very rapid, and was monitored by continuous measurement and logging of the redox potential in solution by use of a microcomputer. The relationship between redox potential and manganese extraction was established empiricaly for each set of conditions by the use of a technique in which a calibration run was conducted in paralel with each leaching run. The study involved a number of batch leaching runs, and demonstrated that, of the variables investigated, only the initial ferous ion concentration and the reaction temperature afect the rate of manganese extraction. The final extraction did not vary. The reaction was modeled from the results by use of the shrinking-core model and Britan's activation-energy model. The later was found to provide a significantly better fit to the data.

Jan 1, 1991

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By A. M. Copeland, A. J. Barrett

The use of hydraulically placed backfill in the deep gold mines of South Africa has increased rapidly over the past decade. The backfill that is delivered to the placement areas has a relatively high moisture content, and it is therefore pumped into geotextile containment bags that allow excess water to drain out but retain solid particles. The specific problems associated with this process that are addressed in this paper include the loss of solid particles entrained in the excess water, the rate of strength gain of the backfill, and the post-placement shrinkage of the backfill. The results of laboratory, surface stope, and underground tests are described. The parameters that were varied included the slurry density, the particle-size distribution, and the feed rate of the slurry the concentration of added flocculant; and the type of geotextile used as containment. Suggestions are given for the optimization of the placement properties of backfill.

Jan 1, 1994

By J. R. de Wet

The behaviour of mild steel in aqueous cyanide solutions similar to caustic cyanide elution solutions was investigated at high temperature in electrochemical experiments. The anodic polarization diagrams of mild steel indicated that steel may undergo active dissolution under these conditions. The rare occurrence of gold plating in practice is the result of the limiting of the anodic dissolution of the steel by the presence of a passive layer on the steel. This passive layer is stable only in a certain potential range, and the free corrosion potential attained determines whether the steel will be passive or active. For conditions typical of elution columns, several corrosion potentials are possible, depending primarily on the initial condition of the steel and the concentration of oxygen in the solution. If these conditions result in the formation of a passive layer on the steel, changes in concentration and temperature will not necessarily result in plating since the layer may exist in a metastable form.

Jan 1, 1993

By W. A. Lenhardt

During the past five years, several research projects on the causes of mining induced seismicity have been carried out by the Rockburst Research Department at Western Deep levels Limited. This paper summarizes the results of these investigations. Several types of mining-induced seismic events are addressed, and models of their mechanisms are presented. It is shown that most of the seismicity results from mining in geologically disturbed areas, and ways and means are discussed to reduce the seismic potential. Stabilizing pillars, for instance, have been introduced to reduce stresses at the stope face and to alleviate the facebursting problem. Facebursts still occur in areas of very low stresses, and pillars became the source of very large seismic events (M >3). At this stage, the understanding gained of pillar-associated events allows a review of current mining practices. Further, it makes possible an examination of the efficiency of measures to alleviate the effects of various seismically prone situations.

Jan 1, 1992

By M. B. Cortie

The historical development of materials engineering in the mining industry Is briefly reviewed, and some of the factors currently influencing the industry in South Africa are discussed. Material usages in various parts of the mining operation are surveyed. The predominant mechanisms in the degradation of materials in mines are wear, corrosion, and fatigue. The issue of corrosion-abrasion Is considered, but it Is concluded that abrasive wear predominates in most rock-handling and comminution applications and that, in general, little economic benefit Is to be gained in those applications by the use of existing corrosion-resistant alloys. However, alloys with a measure of corrosion resistance find profitable application elsewhere in the mining environment. The use of other engineering materials such as polymers, ceramics, al1l1inium, and various ferrous alloys may be economically viable in a variety of niche situations. Identification of the most cost-effective material in each case calls for a systematic approach and some patience.

Jan 1, 1996

By C. J. Fauconnier

The main purpose of the paper is to determine the contribution of fluctuations in barometric pressure to flammable gas explosions in South African mines. For this purpose, the barometric-pressure patterns preceding each of the 59 major explosions in South African gold and coal mines over the past 20 years were analysed. It is concluded that diurnal fluctuations in pressure do not have a major influence on the accumulation of gas in the underground workings, but that pressure drops associated with cyclonic weather systems moving across the country over a number of days are the major factor contributing to gas explosions in mines. To illustrate some of the points made in the paper, the Hlobane Colliery explosion of September 1983 is used as a case study. In the final section, several general conclusions are drawn and recommendations put forward as to how mines should recognize and react to meteorological phenomena that may lead to an increased probability of gas explosions in underground workings.

Jan 1, 1992

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

It is desirable to have a model, or method, for major project development, which will enable flexible modelling of separation circuits. This ability improves the understanding of circuits and how they should be operated, especially in a design phase, where various options are evaluated and decisions are made on the required number of stages and configuration. This paper describes existing gravity separation circuit modelling theory and concepts, as defined by Holland-Batt1 (separation window, separation efficiency and proportionality of efficiency). The crux of the paperis the application of numerical analysis to fit raw separation data by means of a modified Bézier-Spline. The paper proposes an alternative to the theory developed by Holland-Batt that provides more flexibility in the modelling of separation stages and curves, which include S-shaped curves. The paper proposes a solution to the challenge of continuously extrapolating data, and the first difficulty normally encountered, which is the fitting of an appropriate empirical formula to raw data.

Jan 1, 2007

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007

By Y. C. Kim

The estimation of local recoverable reserves using the widely spaced exploration drill hole information in an open-pit mine is probably one of the most difficult tasks in ore reserve estimation. The difficulty of this problem is magnified if the grade distribution is highly skewed, such as in a gold deposit. This paper describes the results of performance comparison of three different kriging techniques in an open-pit gold - silver deposit. The three different kriging techniques compared in their local recoverable reserve estimation capabilities are: (1) lognormal kriging, (2) indicator kriging, and (3) probability kriging. For performance comparison, the predictions are compared with the actual recoverable reserves determined from blast hole information. Based on the results from one test bench, both indicator and probability kriging performed better than lognormal kriging, perhaps owing to samples not being truly lognormal. Between indicator and probability kriging, probability kriging results were definitely superior to indicator kriging results.

Jan 1, 1987

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By W. K. Osae

A value assessment model which uses deal objectives, financial and non-financial indicators as a guide to assess value creation in mergers and acquisitions. The extent to which post- merger deal objectives are achieved and the potential benefits derived from mining deals that may not necessarily be financial of nature, but which are necessary to sustain and enhance future performance, were considered. The pre-merger and post-merger performances based on some financial indicators that reflect profitability for shareholders were also used. This value assessment model was used to assess four major deals that have occurred in the South African mining industry since 2003 as part of a postgraduate dissertation. In this paper, the Harmony and ARMgold merger is used as an example of how the model can be applied. The model?s relevance and applicability can also serve as a guideline in developing a framework or holistic guideline in assessing whether mining BEE deals in South Africa create value.

Jan 1, 2011

A high volume of slimes which are separated out during the mining of heavy mineral sands has a high environmental impact and results in great capital as well as operational expenses. The presence of clay minerals drastically increases the slimes volume that needs to be catered for due to its low settling capability as well as swelling characteristics. By adding coagulants in the form of cations and organics, one can improve the settling rate of the minerals as well as the degree of solid bed compaction. The addition of flocculant, which is currently used in industry to improve settling rate, is detrimental to solid bed compaction. By combining the cations and flocculant one can dramatically improve the solid bed compaction. This combination is, however, detrimental to the settling rate of kaolinite-rich slimes but improves the settling rate of smectite-rich slimes. Organics can also be used to produce a clear supernatant and improve the settling rate.

Jan 1, 2010

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013