Search Documents

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By B. Mbuya, A. F. Mulaba-Bafubianda, J. M. Mvita

The paper explains the main effects of input leaching parameters, such as addition of a reducing agent, acidity, agitation, temperature, and leaching system potential, in relation to observed and predicted yields of sought-after cobalt. An artificial neural network coupled with graphical probability networks was developed wherein the abovementioned input parameters were used to predict the percentage of dissolved cobalt. Furthermore, similarities and differences between the Bayesian and neural network approaches in terms of their key outcomes are compared with respect to study of the dissolution of cobalt in sulfuric acid. Key results indicate that there is a need to use neural network results to predict conditions for dissolution of cobalt, while using Bayesian network to explain inferences about conditions of the input parameters, thereby achieving realistic predictions.

Jan 1, 2023

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By J. van Zyl, K. B. Le Bron, L. J. Gardner

Pillar design is a crucial aspect of underground mining engineering, as it directly impacts the safety, stability, and overall effectiveness of mining operations. In this paper we present a method to calculate pillar stability based on the strain criterion and pillar load inversion concept, which complements the empirical pillar strength formulae. Those formulae do not account for certain parameters that can affect the stability of the pillars, e.g. weak layers, changes in stress orientations due to mining, orebody dip, mining layout complexity, and the influence of regional stabilizing pillars. The approach presented here is not intended to replace the empirical method; rather, we suggest using it as the initial step in the pillar design process. This should be followed by iterative numerical modelling to study pillar behaviour, define pillar stability, and optimize the pillar design by considering site-specific and representative rock mass properties and criteria.

Jun 10, 2024

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

By D. G. Krige

The problem addressed is that of estimating grade differences between sub- divisions of a new gold mining prospect when only borehole results are available. Such differential grade estimates are required in choosing the best area for initial production, and in defining the grade profile over the mine's life for purposes of feasibility studies. It is also often necessary to differentiate between the grades and hence the values of subareas, owned by separate companies, for the purpose of fixing relative share participation percentages in the new mining company. It is shown that exaggerated grade differentials will be obtained from grade estimates of the subareas based only on boreholes within each such subarea, respectively, and that it would be more realistic to apply some 'smoothing', preferably by kriging. This is feasible because the lognormal-de Wijsian model can be used to give an indication of the spatial structure for the boreholes, even where they are spaced far apart; also the degree of 'smoothing' indicated is shown to be relatively insensitive to inaccurate estimates of the relevant semivariogram parameters.

Jan 1, 1987

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By D. D. Ndenguma

This investigation compares the results from an experimental and numerical study of air flow in a scaled-down underground coal mine model. This was done in order to determine if numerical analysis can be relied upon when searching for ventilation solutions to control high concentration of coal dust and methane gas in underground coal mines. Steady state analyses were used to identify flow patterns and recirculation regions within the mining section while transient state analyses were used to determine the time taken to extract the initial air from the model. The agreement between the experimental and numerical results indicates that numerical modelling is useful in this regard. The study went further to devise a method of determining the optimum position of the jet fan that is responsible for mine-gas dilution at different stages of mining.

Jan 1, 2014

By F. Petersen, W. van Dyk, J. Bonsu, A. Isafiade

"This paper aims to demonstrate how a systemic approach can be applied to the analysis of the causes of accidents in South African mines. The accident analysis framework used was developed previously by the authors from the combination of the Mark III version of the Swiss Cheese model, Incident Cause Analysis Method (ICAM), the Nertney Wheel model, and safety management principles. Data on 91 accidents occurring from 2010 to 2012 at the site of a platinum mine in South Africa were used to populate the newly developed framework. The results obtained show that while routine violations (45% of all accidents analysed) were the most common form of human error, problems in the physical environment of workers were the most common workplace factor (39.6% of all accidents analysed). Furthermore, inadequate leadership was found to be the most common systemic factor responsible for accidents (51.6% of all accidents analysed). Some workplace factors were more commonly associated with particular unsafe acts than others, and some systemic factors were more associated with particular workplace factors than others. The outcome of this study demonstrates that systemic factors, rather than human errors and violations, are the chief causes of accidents in the mining sector. IntroductionThe mining industry is a very important sector of the South African national economy. A major factor threatening the sustainability of this industry is mining accidents, which frequently result in injuries or deaths, destruction of property, and pollution of the environment. In the past, mining accidents have led to the shutdown and threat of shutdown of mines (Ryan, 2008; Mail and Guardian, 2011). The country stands the risk of incurring significant losses if the mining industry continues to experience shutdowns. In 2012, the mining sector accounted for R262.7 billion (equivalent to US$32.83 billion) representing 8.3% of GDP directly, on a nominal basis (Chamber of Mines of South Africa, 2013).Mining safety is a global concern and has attracted significant international attention. This has precipitated various studies into different aspects of mining. Unfortunately, human error has been blamed for the majority of these accidents. A study by the US Bureau of Mines found that human error is the cause of almost 85% of all accidents (Patterson and Shappell, 2008). In Australia, it is the cause of two out of every three occupational accidents (Patterson and Shappell, 2008). Various mining companies maintain that they run efficient systems, and hence the behavioural problems of workers are to blame for most accidents. An understanding of accident causality could be a major step in the quest to reduce accidents. Only with a good understanding of the accident process can effective remedies can be designed."

Jan 1, 2017

By H. W. Glen

The National Institute for Metallurgy - usually referred to as NIM - has become the Council for Mineral Technology, or Mintek. The Honourable F. W. de Klerk, Minister of Mineral and Energy Affairs, announced the change of name at the official opening of the main entrance to Mintek's premises on 30th October, 1981. Awards for bravery Two men who disregarded the dangers of fiercely burning timber and falling rocks to douse an underground fire, using their hard hats to scoop water from a drain, received the Chamber of Mines Award for bravery at a ceremony held at West Driefontein Gold Mine near the end of October.

Jan 1, 1981

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011