Search Documents

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By J. van der Merwe, C. Phetolo, V. Matjeke

The mechanical properties and microstructure of AlSi10Mg alloy samples that were printed by selective laser melting (SLM) were studied to determine the effect of processing parameters and building orientation. After printing, the alloy was stress relieved at 250°C for 2 hours. The microstructures were analysed by optical microscopy and scanning electron microscopy (SEM) to determine the alloy phases and distribution. Phase transformation characteristics of the material were evaluated using differential scanning calorimetry (DSC). Mechanical properties were determined by subjecting the XY- and Z-built samples to tensile and nano-indentation testing. The samples from the tensile tests were then used to perform fractographic analysis by SEM. The microstructural properties in each orientation revealed a non-homogeneous microstructure which was characterized by a semi-elliptical tract and fine silicon precipitates, which were found to be softer along the fusion zone. The DSC thermograms revealed that the material underwent two phase transformations during the first heating cycle. The mechanical properties revealed a higher UTS, higher yield strength, and a lower percentage elongation in the Z orientation than in the XY orientation. Fractographic analysis showed that crack initiation in both orientations started from the surface in a brittle manner due to surface flows, and then propagated via microvoid coalescence.

Jul 1, 2021

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By D. F. Caicedo, I. A. Brum, L. A. Betancourt

Ferricyanide ()()*is one of the most stable cyanometallic complexes present in the gold mining effluents. This cyanocomplex is hard to degrade by natural attenuation and generates a negative impact on aquatic environments. Although free cyanide (CN-) can be obtained by acidifying the solution, the CN- is lethal for all forms of life. The oxidation of ()()* in a typical photocatalitic system was evaluated with the addition of H2O2. To verify the degradation, chemical parameters, such as free cyanide, the formation of ammonia, nitrate, and total iron were analysed at the end of the process. The degradations obtained were up to 70% in a heterogeneous photocatalysis system with TiO2, and a low rate of dissociation was observed by photolysis. The best result was achieved with the H2O2 and TiO2 photocatalytic system, and the stoichiometric concentration was about 2.5 times less than the peroxide used in the real gold mining industry, reaching 83% degradation. The photocatalytic process obtained less toxic byproducts than the original synthetic ferricyanide used as mining wastewater. Keywords: Cyanide, heterogeneous photocatalysis, titanium dioxide, UV radiation, gold wastewater

Jan 1, 2020

By R. D. Cromarty, J. Du Toit

"Penetration of matte into tap-hole bricks causes detrimental refractory wear, which can lead to furnace breakouts. The ability of the tap-hole clay to form a protective layer on the brick, thereby limiting matte penetration was investigated by examining the interaction between platinum group metal (PGM) matte, tap-hole clay, and alumina-chrome refractory bricks on a laboratory scale.Samples containing clay and brick as well as samples containing clay, brick, and matte were heated to different temperatures to establish the clay-brick interaction and the extent of matte penetration. The greatest degree of physical contact between the brick and clay was achieved at curing temperatures of 600°C. Poor clay-brick contact was observed in the sample that was heated to 900°C.Matte displaced the clay in the clay-brick-matte sample that was heated to 1350°C, with significant matte penetration into the brick. Less matte penetration was observed when the clay-brick-matte sample was heated to 1500°C. Less matte penetration was also observed in the claybrick- matte sample in which the clay and brick were pre-baked at 800°C, and the sample then reacted with matte at 1350°C. IntroductionFloatation concentrate from ore from the eastern Bushveld Complex of South Africa, specifically the Platreef, Merensky, and UG2 reefs, forms the feed to the Polokwane platinum smelter (Hundermark, De Villiers, and Ndlovu, 2006). The ore from the UG2 Reef has a high chromite content, which requires high operating temperatures (1500–1700°C) to avoid chromium spinel build-up in the furnace hearth. These high operating temperatures lead to matte superheats in the vicinity of 500– 600°C, which put increased demands on the refractory materials (Nelson et al., 2005).Upon tapping, the matte moves through the tap-hole, which consists of an aluminachrome refractory brick-lined tapping channel (Hundermark, De Villiers, and Ndlovu, 2006). The flow of molten matte is stopped by the injection of tap-hole clay to form a plug in the tap-hole. The tap-hole clay hardens and strengthens during curing to obtain the required hardness and refractoriness against penetration, corrosion and erosion (Nelson and Hundermark, 2014)."

Jan 1, 2016

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

By A. E. Landsberg, K. C. Corin, G. Stroebel, J. A. Miller, M. Becker, H. J. J. Gordon

Geometallurgy represents an integrated approach to mine planning and operation whereby the naturally occurring ore variability and its effects on all key downstream activities in the mine life cycle are considered. Process mineralogy is one of the key components of this integrated approach. This paper focuses on understanding some of the mineralogical variability across the Swartberg Cu-Pb-Zn sulfide ore in South Africa and its consequent effects on flotation performance. This process mineralogy project is motivated by the planned changeover and expansion of the Black Mountain Mines concentrator to process solely Swartberg ore compared to the run-of-mine blend currently being treated at the plant. Eight samples spanning the main lithological units of the ore body are described using quantitative mineral-textural data and bulk sulfide batch flotation performance to establish five process mineralogical or geometallurgical units comprising: quartz-pyroxmangite-magnetite, quartz-amphibolemagnetite, quartz-magnetite, garnet-magnetite-quartzite and mica-quartzite ores. Important mineralogical characteristics affecting Cu, Pb and Zn recovery, grade and selectivity specific to the different ore samples are discussed. Ultimately, the use of ore-specific process mineralogical and geometallurgical knowledge allows for better mine planning and plant optimisation. Keywords: Flotation, polymetallic base metal sulfide ore, process mineralogy, ore variability

Jan 1, 2020

By L. Stamenov, A. Grigoryan, M. Nolte, E. Ayvazov, K. Evtiminova

Dundee Precious Metals Inc. (DPM) owns and operates the Ada Tepe gold mine and processing facility (previously referred to as the Krumovgrad Gold Project) located in south-western Bulgaria. The Ada Tepe mine became the first green filed project in past 40 year in Balkans and one of the few in Europe when it was commissioned during the first half of 2019. The plant produces a high-grade gold silicate concentrate generated through its comminution circuit and staged floatation reactors (SFR’s) while depositing its tailings in a state-of-the-art Integrated Mine Waste Facility (IMWF). This paper presents the successful commissioning, ramp-up and optimization of the Ada Tepe processing plant and how the various challenges, including that of an inexperienced front-line workforce, were overcome. More specifically addressing how the implemented modern processing technologies and the operational readiness program, supported the people and process to achieve the design parameters safely and consistently. Keywords: Commissioning, Optimization, Innovation, Gold mine, Digital mine

Jan 1, 2020

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020

By N. W. Munro

SYNOPSIS Certain disadvantages associated with the use of Anfex have been raised on previous occasions. This interim investigation shows that by loading at lower pressures the sensitivity to initiation of Anfex can be improved. Associated with this is a reduction in velocity of detonation and charge density which should lead to more desirable fragmentation. The effect of lower loading pressure on other factors is also considered. INTRODUCTION Discussion at the Symposium on the use of Anfex in Underground Mining, conducted by the South African Institute of Mining and Metallurgy during May 1968 showed that there was considerable uncertainty and diversity of opinion on the characteristics of Anfex and its method of application. Some of the disadvantages associated with the use of Anfex were: Inadequate sensitivity to initiation; Excessive fragmentation of the rock and damage to the hanging and footwalls; Wastage as a result of blow-back; Poor water resistance. As a result of this, further investigations on the properties of Anfex have been carried out and, although these have not reached finality, it is considered that a progress review may be of interest and assistance to the mining industry. EXPERIMENTAL TECHNIQUE The work was carried out on a laboratory-scale where, for test purposes, the explosive was loaded into 1 in. (nominal) internal diameter steel pipes unless otherwise stated. Charging was conducted with a 1 in. (nominal) Schutte-Koerting eductor having a 0.2 in. internal diameter venturi nozzle, the Anfex being fed into the eductor from a conical hopper fitted directly above it. A 5 ft long copper loading tube with outside and internal diameters of 3/4 in. and 5/8 in., respectively, was fitted to the discharge end of the eductor. The remote end of the loading tube was inserted into the test pipe so that it was about 6 to 8 in. from the closed end of the pipe. The loading apparatus was withdrawn as the pipe filled, maintaining approximately the same stand-off distance throughout the operation. REVIEW Sensitivity to initiation Sensitivity of Anfex to initiation was found to deteriorate when the dynamic pressure of the air to the eductor was increased. This was attributed to increasing charge density and it was found that at a charge density of about 1.05 g/cm3, which

By K. Premlall, R. M. Dire, H. Bissett, D. Delport

Tungsten carbide is a fine grey powder. It can be formed into shapes by compacting with the addition of a binder. Spherical particles are generally preferred in additive manufacturing as they pack together more efficiently than non-spherical particles, promoting a uniform powder bed density, better flowability, and elimination of internal cavities and fractures, resulting in a better quality of final product. The particle shape of powders can be transformed into spherical through the process of spheroidization. However, due to its high melting point, tungsten carbide could be difficult to spheroidize. Tungsten carbide was spheroidized using an inductively coupled radio frequency plasma at various plate powers between 9 and 15 kW. The influence of additional H2 in the sheath gas on the chemical composition of the tungsten carbide product was also investigated by means of XRD, which indicated that WC is converted to W2C at higher H2 concentrations. Optical analysis of SEM micrographs indicated that the spheroidization ratio increased with increased plasma energy.

Apr 1, 2021

By R. S. J. Du Toit

SYNOPSIS This paper is based on a thesis dealing with the problem of basing the current rate at which money is collected from mine owners to pay compensation for pneumoconiosis in the future, on the current dust hazard on mines. The certification of pneumoconiotics and the incidence of pneumoconiosis are discussed against the background of existing legal provision for collecting funds for compensation. The various pneumoconiosis indices are considered. In the data analyzed, the only pneumoconiosis index common to a number of classes of mines is the time it takes to develop pneumoconiosis. Sets of dust indices and pneumoconiosis indices are computed. Expressions are derived for the time it takes to develop pneumoconiosis as a function of the dust hazard, and for the collection of funds as a function of the time available for collection. From these two expressions follows an expression for the rate of collecting funds as a function of the dust hazard.

By E. Demir

Transportation cost is the dominant cost and accounts for almost half of the total mining cost in surface mining. Therefore, determining transportation cost is critically important for the economic feasibility of mining projects. Turkey produces around 85 million tons of lignite per annum. The biggest state-owned company, Turkish Coal Enterprises (TKI), accounts for 43 per cent of the country?s total lignite production. Around 85 per cent of the produced lignite is used in power plants for electricity generation and 15 per cent is used for domestic heating in cities and urban areas. On behalf of the Turkish government, TKI distributes around 2 Mt of lignite annually, at no cost to poor needy families countrywide in accordance with Social Assistance and Solidarity Funding aid. Subcontractors are utilized for lignite transportation, and conflicts arise due to the different transportation cost calculations at different mines. A robust model that provides unbiased cost estimations is therefore of paramount importance. This paper presents the transportation cost estimation software, NAKMAL, that has been developed for estimating the transportation cost of lignite from the mine face, including excavation and loading, to various final destination points through five different transportation scenarios. NAKMAL was designed using VisualStudio.NET, validated using field data and some case studies, and it is currently being used by TKI for calculation of transportation cost country-wide.

Jan 1, 2012

By M. G. B. Wheeler

SYNOPSIS This report outlines the development of a model to simulate the radiometric sorting of gold- and uranium-bearing ores. The developed program indicates the optimum mass, reject percentage, and expected reject gold and uranium grades for a radiometric sorter. It achieves this by statistical analysis of the data gathered from a large sample of rocks in the required size range for a particular mine. The program can be used in the optimization of existing sorters, as a design tool for new radiometric sorters, and in feasibility studies on radiometric sorting.

Jan 1, 1989

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005