Search Documents

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

Four engineering products and three consumer products have received awards in the 1978 Shell Design Awards competition organized by the Design Institute of the South African Bureau of Standards. Norman Hanson Visiting Fellowship The Norman Hanson Visiting Fellowship, supported jointly by the National Development Fund for the Building Industry (inaugurated by the Building Industries Federation (8.A.)), the Institute of S.A. Architects, the Association of S.A. Quantity Surveyors, and the National Building Research Institute of the CSIR exists to finance fully or wholly visits by eminent authorities from overseas to South Africa for the purposes of seminars, informed discussions, consultation, and possible active participation in scientific, technological, and development projects of importance to the building industry.

Jan 1, 1979

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984. New President On 29th March, 1985, Mr B.C. (Bertie) Oberholzer, Manager of East Driefontein Gold Mine, was elected President of the Association of Mine Managers of South Africa for the ensuing year. Bullion from old film A pollution-free chemical method of producing silver that is 99 per cent pure-and therefore of bullion quality-from scrap photographic film and paper has been developed by a British company.

Jan 1, 1985

By P. J. D. Lloyd

The Federation of Societies of Professional Engineers (FSPE) recently conducted a survey of professional engineering manpower in South Africa. This article presents the data relevant to mining and metallurgical engineering. FSPE in their survey attempted to determine the supply of engineers in South Africa both from local universities and by immigration. The immigrants gave some problems in that it is difficult to know whether a man who claims to be professionally qualified really is. However, it was estimated that the ratio of immigrants who claimed to be qualified to those who really are the equivalent of our local graduates was between 1,0 and 1,9 for mining engineers, and between 2,0 and 4,1 for metallurgical engineers.

Jan 1, 1980

By M. Timucin

High-temperature phase relations and thermodynamics of the condensed phase region of the Pb-S-O system at 1473 K were analysed by use of the available information. The sub-regular solution models on Pb-PbS and PbO-PbSO4 continuous melts were used in conjunction to generate a consistent set of thermodynamic and phase equilibrium conditions for the Pb-S-O system. The directions and distributions of conjugation lines between melts of this system were derived with relevant activity and composition data. The calculations permitted the thermodynamic analysis of direct lead smelting and the construction of isothermal reaction diagrams for the system in terms of oxygen and sulphur partial pressures at 1473 K.

Jan 1, 1989

By T. Dimillo, R. G. B. Pickeirng

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular ore bodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focussed on the haulages, cross cuts and raises. The non-explosive rock breaking method has many other applications, however, it is the integration with the Tunnel Digging Machine that results in the first, cost effective, Continuous Tunnelling Machine for hard rock mining.

Sep 1, 2001

By C. J. Fauconnier

The various methods of detecting fires and heatings in collieries are reviewed. The methods described range from those relying principally on human senses to sophisticated methods employing infrared technology to detect traces of the products of oxidation and combustion. The advantages and disadvantages of various gases employed as indicator gases for the early detection of heatings and fires are discussed, and recommendations are made in this regard. The operation of a modern infrared carbon monoxide detection system is described, and the differences in operation and application of telemetric systems, tube-bundle systems, and up cast-shaft monitors are discussed In conclusion, some indication is given of the capital outlay required for typical early-detection systems.

Jan 1, 1981

By M. U. Özbay

A series of blasting experiments was carried out in an up-dip stope of a gold mine using short-perioddelay electric detonators. The main object of the investigation was to show the interactive effects of short-delay blasting. The delay range over which observations were made was restricted to between 10 and 200 ms. To quantify the blast results, data were collected on fragmentation, throw, position of muckpile, and ground vibration. For comparative purposes, blasting parameters for conventional pyrotechnic sequential firing were also measured. The paper describes the most relevant parts of the study and gives the experimental results. The interactive effects of short-delay blasting are analysed, and some aspects of the breaking mechanism are discussed.

Jan 1, 1985

By R. S. Francis

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

By J. Dvorácek

Mine water poses a significant problem in lignite coal mining. The drainage of mine water is the fundamental prerequisite of mining operations. Under the legislation of the Czech Republic, mine water that discharges into surface watercourse is subject to the permission of the state administration body in the water management sector. The permission also stipulates the limits for mine water pollution. Therefore, mine water has to be purified prior to discharge. Although all mining companies operate mine water treatment plants, there is hardly any utilization of the final effluent. The high expenditure involved in the more sophisticated methods of mine water treatment has fuelled the search for the commercial utilization of the effluent.

Jan 1, 2012

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk. Keywords platinum, mining, community, socio-economic impact, stakeholders, conflict, labour unrest, social licence to operate, investment, Africa.

Mar 1, 2013

By Arun Vathavooran, Adrian Singh, Michael Fletcher, Rainer Imhof

The Imhoflot G-Cell, a new development in the pneumatic flotation technology (which incorporates centrifugal forces in the separating vessel) is a recent innovation in the mineral processing world. The G-Cell was invented by Dr Rainer Imhof and commercialised by Maelgwyn Mineral Services Ltd. In a short time span a number of plants and units have been successfully commissioned in the mineral processing industry. In addition, a number of industrial G-Cell flotation plants are in the process of construction for the purpose of coal preparation and environmental remediation. In this paper two industrial installations have been highlighted together with a pilot plant test programme investigating ultra fine flotation recovery for a base metal operation.

Jan 1, 2007

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By J. K. E. Douglas

PRESIDENTIAL ADDRESS Given by Mr J. K. E. DOUGLAS, M.Se. (Eng.) (Rand) SYNOPSIS Lime is the most widely used and the cheapest chemical alkali known to man and virtually every product we use or eat has required lime in some phase of its manufacture. Its use goes back to the earliest days of man and many ancient buildings and writings bear testimony to this. The manufacture of lime involves quarrying, crushing and screening of limestone and the burning of the sized stone in kilns of which there are several types. The earliest kilns were of very crude design and only in comparatively recent times have large capacity, automated and scientifically controlled kilns been developed. The history of the South African lime industry is largely that of the three main lime companies and their story is briefly told. No other material used in industry has a greater diversity of uses or more varied functions and lime has applications in most South African industries. The main applications are in the production of gold and uranium, iron, steel and ferrochrome, carbide, sugar and paper and for water treatment, agriculture and building. The Republic is well endowed with high quality limestone and the conclusion is drawn that many other minerals will have been exhausted before we run out of limestone with which to process them. The expansion of the lime industry has in the past kept pace with the requirements of industry and the future demand is expected to grow in parallel with the growth of these industries. Since the war this growth has been phenomenal and with our expanding populations and abundance of raw materials it should continue in the years ahead. Limiting factors are the shortage of skilled labour and the distance from export markets. Confidence is expressed that the challenges of the future will be met and that the lime industry will continue to make an important contribution to the growth and prosperity of South Africa. INTRODUCTION Lime, gentlemen, is known to all of you. Like myself, most of you have undoubtedly found it to be, on the appropriate occasion, a most pleasant flavouring for gin. But this lime, or rather its juice, was in earlier days more than just a flavouring. In the days of sail it was vital to the health of sailors as a deterrant against the scourge of all sea-going men-scurvy. It thus played a small but important role in the opening-up of trade routes around the world on which was based the original wealth of many of today's more advanced nations. I propose to address you on the subject of lime this evening, not the citrus variety I have just mentioned, but the most widely-used and cheapest alkali known to man, which, largely unsung, plays an even more vital part in modern industry than did its namesake in the development of inter-continental trade. In the time at my disposal, I propose to tell you something of the history, geology and technology of lime manufacture. Then I will briefly sketch for you the development of this industry in South Africa and indicate the role it plays in supplying the requirements of many of our important industries. Finally we will attempt to look into the future. The importance of this chemical alkali to our modern civilization is seldom fully appreciated-virtually every product we use or eat has required lime in some phase of its manufacture, either directly or indirectly. It is one of those basic materials, along with iron, coal, sulphur, salt and petroleum without which industry and, in fact, our modern way of living could not exist. Fortunately, nature has endowed the world with a plentiful supply of the limestone from which lime is derived and most countries have deposits adequate for their requirements. As a result, not only has there been little trade in lime products between countries but in the past the widespread occurrences of limestone have set a pattern of numerous small plants each serving a limited area. These plants were generally crude affairs incapable of producing a quality product. It is not surprising that, in an industry comprised of small producers with limited financial resources and in fierce competition with each other, there was little interchange of information. Technological development was therefore slow and the industry tended to be regarded as a backyard operation. Its popularity was not enhanced by the fact that lime is difficult and unpleasant to handle if proper facilities are not provided. In recent years the lime industry has undergone very radical changes to meet the more exacting requirements of today's more sophisticated consumers. Only since the war have the larger companies emerged with proper management, highly mechanized plants and a scientific approach. HISTORY Lime was one of the first chemical reagents used by man and consequently lime burning is one of the oldest of the chemical industries. The use of limestone dates back to the stone age when primitive man used limestone to build fireplaces, construct shelters and make crude tools and weapons. It is probable that lime was first discovered by him when the stone in these fireplaces disintegrated to a white powder which he could use for decorative purposes. The first recorded use of limestone was when huge blocks of limestone were used to build the pyramids of Egypt in 4,000 to 2,000 RC. It was not long after this that the beauty of marble, which is in fact a limestone, came to be appreciated and it found wide application in sculpturing and for decorative wall construction. Originally lime, mixed with sand, was used mainly as a mortar for building purposes, the earliest record of its use for chemical purposes being in 350 B.C. in a report of the wreck near Marseilles of a ship carrying a cargo of linen and lime 'for its bleaching'1. Cato mentioned the burning of lime kilns in 184 B.C. and the Romans made extensive use of both limestone and lime for highway construction. A treatise on architecture by Vitruvius who had an official position in the rebuilding of Rome under the Emperor Augustus remained for nearly two thousand

By H. P. Kritzinger, T. C. Kingsle

"Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications, including ferrovanadium, nickel carbonate, nickel laterite, iron ore reduction, and spodumene (lithium) production.This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates."

Jan 1, 2015