Search Documents

By J. N. Van der Merwe, D. P. Roberts

The two components of pillar design formula being used in South Africa are pillar strength and pillar load. While considerable effort has been directed to the determination of pillar strength, the other half of the safety factor equation, the load, has not received the same amount of attention. The load acting on pillars has always been calculated using the Tributary Area Theory (TAT). This paper summarises the recent studies on coal pillar loading using various numerical models. It concludes that although there are meaningful differences under certain circumstances, there is still a compelling argument to use the TAT in coal pillar design. Les deux parties composantes de la formule de conception de pilier généralement utilisée en Afrique du Sud sont la résistance de pilier et la charge de pilier. Tandis que des efforts considérables on été dirigés vers la détermination de la résistance de pilier, l’autre moitié du facteur de sécurité n’a pas reçu la même attention. La charge agissant sur les piliers a toujours été calculée avec la Théorie d’Aire Tributaire (TAT). L’étude présente résume les études récentes sur la charge de pilier de charbon utilisant des modèles numériques variés. La conclusion est que bien qu’il y ait des différences significatives selon les circonstances, il y a toujours un argument puissant pour utiliser le TAT dans la conception de pilier de charbon. Die in Südafrika für die Auslegung von Pfeilern verwendeten zwei Formelkomponenten sind Pfeilerstärke und Pfeilerbelastung. Während beträchtlicher Aufwand zur Bestimmung der Pfeilerstärke gemacht wurde, wurde der anderen Hälfte der Sicherheitsfaktorsgleichung nicht die gleiche Aufmerksamkeit gewidmet. Die auf die Pfeiler wirkende Last wurde immer unter Verwendung der Tributary Area Theory (TAT) berechnet. Diese Arbeit fast neuere Studien betreffend der Belastung von Kohlepfeilern unter Verwendung verschiedener numerischer Modelle zusammen. Die Schlussfolderung ist, daß obwohl unter bestimmten Vorraussetzungen bedeutende Unterschiede existieren, nach wie vor ein bezwingendes Argument besteht TAT in der Kohlepfeilerauslegung zu verwenden.

Jan 1, 2003

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

By P. den Hoed, J. Nell

Tests were conducted on samples of rutile, titaniferous slag and ilmenite; each sample was mixed with coke and chlorinated in a bubbling fluidized bed at 1000°C. Profiles of the rates of chlorination of species were constructed from chemical compositions of the bed residues at different durations. From the start FeO and MnO are chlorinated quickly and all but entirely in a fraction of the time it takes to chlorinate all the TiO2. When the level of FeO is significant, as in slag and ilmenite, FeO is chlorinated faster than TiO2is. In these oxides, there is an inverse relationship between the rates of chlorination of FeO and TiO2during this first stage; the relationship, moreover, correlates linearly with the initial percentage of FeO in the oxide. We identify three stages in the chlorination process; a first, in slag and ilmenite, when FeO is being chlorinated; a second, when TiO2is most readily chlorinated; and a third, towards the end, when the levels of TiO2are reduced to those of other species. The rates at which individual species are chlorinated are analysed in terms of their appreciation or depreciation with respect toTiO2

Jan 1, 2003

By M. Wang, Z. Sui, T. Lou

After smelting, the associated mineral ore accompanying Valuable Metal Compounds (VMC),such as titania and borate in BF., most of the VMC were separated from the metal into the molten slag that is an associated slags. Based on several case studies in laboratories and in a practice in a pilot plant on the associated slags , there occur a feasibility to recovery VMC from the slags by anew process- Selective Precipitation Technique (SPT) on which three continuous steps are involved: (1) The selective enriching the dispersed VMC into a designed mineral phase in the molten slag; (2) The selective coarsening the designed mineral phase with large crystal grain size;(3) The selective separating the coarsen phase from tailing by mineral dressing or hydrometallurgical process . Some results on the recovering the VMC from the associated slags by SPT were summarized as examples in present paper. Keywords: selective precipitation technique, associated slag, recovering metals from slag.

Jan 1, 2004

By R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key aspect of mechanization is the optimization of equipment utilization, and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2007

By E. V. Lilford

A number of countries have introduced codes governing the valuation of mineral assets and securities. The African continent will follow suit in due course considering the importance of the global minerals industry as it relates to the attraction of foreign investment. South Africa is to introduce the Petroleum and Minerals Development Bill legislating the involvement of previously disadvantaged individuals and communities in the country?s minerals industry. One of the challenges facing the successful implementation of such codes and bills lies with the abilities of independent valuators to value mineral properties and projects on a consistent basis. Certain valuation principles and methodologies are applicable in all jurisdictions in the minerals industry. These valuation tools and principles are considered and developed in this report. They have been discussed and developed to encourage minerals valuators to consider and consistently apply the most applicable valuation methodologies.

Jan 1, 2002

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

By K. S. Rao, R. P. Tiwari, V. K. Shrivastava

ABSRACT: In this paper numerical simulation of jointed block mass behaviour obtained in an experimental study has been presented. Singh et al. (2002) conducted extensive tests on the jointed model materials with several joint configurations. The results of this experimental study were used to validate the strength behaviour of numerical block mass model developed using professionally available software. This software basically contains different kinds of material models. From the results of numerical simulation the existence of strength anisotropy was observed. The strength anisotropy so obtained has been compared with the experimental values reported by Singh et al. (2002). The anisotropic curves in both cases are U-shaped with flat base. They show good agreement in sliding mode of failure zone in which inclination ß (= 90° - ?) of joint set-I lie between 20° to 40° for all cases of interlocking. ZUSAMMENFASSUNG: In dieser numerischen Papiersimulation des verbundenen Blockmasse Verhaltens, das in einer experimentellen Studie erhalten wird, ist dargestellt worden. Singh et al. (2002) leiteten umfangreiche Tests auf den verbundenen vorbildlichen Materialien mit einigen gemeinsamen Konfigurationen. Die Resultate dieser experimentellen Studie wurden verwendet, um das Stärke Verhalten des numerischen Blockmasse Modells zu validieren, das mit professionell vorhandener Software entwickelt wurde. Diese Software enthält im Allgemeinen unterschiedliche Arten der materiellen Modelle. Von den Resultaten der numerischen Simulation wurde das Bestehen von Stärke Anisotrophie beobachtet. Die Stärke Anisotrophie also erreicht ist mit den experimentellen Werten verglichen worden, die von Singh et al. (2002) berichtet werden. Die anisotropen Kurven in beiden Fällen sind mit flacher Unterseite u-förmig. Sie zeigen gute Vereinbarung in gleitender Erscheinungsform des Ausfalls Zone, in der Neigung ß (= 90° - ?) von der Verbindung stellenSie Lüge zwischen 20° auf 40° für alle Fälle vom Ineinandergreifen ein. RESUME: Dans cette simulation numérique de papier du comportement joint de la masse de bloc obtenu en étude expérimentale a été présenté. Singh et autres (2002) ont effectué les essais étendus sur les matériaux modèles joints avec plusieurs configurations communes. Les résultats de cette étude expérimentale ont été employés pour valider le comportement de résistance du modèle numérique de la masse de bloc développé en utilisant le logiciel professionnellement disponible. Ce logiciel contient fondamentalement différents genres de modèles matériels. Des résultats de la simulation numérique on a observé l'existence de l'anisotropie de force. L'anisotropie de force ainsi obtenu a été comparée aux valeurs expérimentales rapportées par Singh et autres (2002). Les courbes anisotropes dans les deux cas sont en U avec la base plate. Elles montrent la bonne concordance dans le mode coulissant de la zone d'échec en lequel la inclination ß (= 90° - ?) du joint placez-Je le mensonge entre 20° à 40° pour tous les cas d'enclencher.

Jan 1, 2003

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

By A. Thoraval, K. B. Slimane, O. Ozanam

The REP experiment is part of the research programme conducted by Andra to investigate the possibility of reversible radwaste disposal in a Jurassic (Callovo-Oxfordian) argillite formation at the Meuse/Haute-Marne underground laboratory site in northeastern France. The experiment focuses on the hydromechanical response of the formation to sinking the laboratory access shaft. Modelling of boreholes and shaft sinking operations has helped to optimise measurement point locations based on initial stress tensor anisotropy, while minimising interaction between instrument boreholes. Analyses were made of model sensitivity to intrinsic rock characteristics, hydromechanical coupling properties and sensor installation procedures. L’expérimentation REP fait partie du programme de recherche pluridisciplinaire engagé par l’Andra pour étudier la possibilité d’un stockage réversible des déchets radioactifs dans la formation Callovo-Oxfordienne des argilites du site de Meuse/Haute-Marne (Commune de Bure - France). Cette expérimentation permettra d’étudier la REponse hydromécanique de la formation aux sollicitations engendrées par le fonçage du Puits d’accès du laboratoire souterrain de recherche. Afin d’optimiser le positionnement des points de mesures, compte tenu de l’anisotropie du tenseur des contraintes initiales, et de minimiser les interactions entre les forages d’instrumentation, des modélisations des forages et du creusement du puits ont été conduites. Des analyses de sensibilité aux caractéristiques intrinsèques de la roche, aux propriétés de couplage HM et aux protocoles d’installation des capteurs ont été faites. Die REP-Untersuchung ist Teil des multidisziplinären Forschungsprogramms, das die ANDRA im Callovo-Oxfordian-Tonstein in situ am Standort Meuse/Haute Marne (Gemeinde Bure – Frankreich) im Hinblick auf eine Eignung zur reversiblen Lagerung radioaktiver Abfälle durchführt. Dabei soll das hydro-mechanische Verhalten der Formation auf die Beanspruchungen, die durch das Abteufen des Zugangsschachts zum Untertage-Forschungslabor erzeugt werden, untersucht werden. Zur optimalen Positionierung der Messpunkte unter Berücksichtigung der Anisotropie des Tensors der Ausgangsspannungen und zur Minimierung der gegenseitigen Beeinflussung der Instrumentierbohrungen wurden ein Schachtabteuf- und Bohrmodelle entwickelt. Zur Untersuchung der inhärenten Eigenschaften des Gesteins, des gekoppelten HM-Verhaltens und der Installationsprotokolle der Messsonden wurden Sensibilitätsanalysen durchgeführt.

Jan 1, 2003

By A. Bouvard, N. Hoteit, E. Boidy, F. Pellet

In the context of the construction of an Underground Research Laboratory devoted to the feasibility studies of radioactive waste deposits, it appears of the utmost importance to study the long-term behaviour of rock, over a long time period. In this paper, some results of tests performed on the argillite from the Meuse-Haute-Marne site test in Eastern France are presented. Then a numerical simulation of one of this test using the viscoplastic damaging constitutive law proposed by Lemaitre is presented. Finally, this law is used to simulate numerically the behaviour of the rock at the wall of a circular tunnel in order to determine the extension and the change along the time of the Excavated Damaged Zone (EDZ). Advantages and limitations of the model are discussed. Dans le cadre de la réalisation d’un laboratoire de recherche souterrain conçu pour étudier la faisabilité d’installations de stockage de déchets radioactifs, il apparaît fondamental de caractériser non seulement le comportement viscoplastique à très long terme des matériaux mais aussi les phénomènes d’endommagement consécutif à la redistribution de contraintes provoquées par l’excavation des cavités. On présente ici les résultats d’essais réalisés sur les argilites du site de Meuse/Haute-Marne et destinés à caractériser leur comportement visco-endommageable. Il est ensuite procédé à une application de la loi viscoplastique endommageable de Lemaitre pour simuler l'un de ces tests. Les apports et les limites d'un tel modèle sont mis en évidence par des simulations numériques du comportement de la roche au pourtour d'une galerie circulaire permettant de suivre l’évolution au cours du temps de la zone endommagée (EDZ) à la paroi . Im Rahmen des Baus eines unterirdischen Forschungslabors für die Untersuchung der Machbarkeit von Deponien für radioaktive Abfälle erweist es sich als äußerst wichtig, das langfristige Verhalten von Gestein über einen langen Zeitraum zu untersuchen. Im vorliegenden Artikel werden einige Ergebnisse von Untersuchungen vorgestellt, die mit Tonschiefer aus der Meuse-Haute-Marne in Frankreich durchgeführt wurden. Anschließend wird eine numerische Simulation der Untersuchungen unter Verwendung des von Lemaitre vorgeschlagenen viskoplastischen Verformungsgesetzes vorgestellt. Schließlich wird dieses Gesetz auf die numerische Simulation eines Kreistunnels angewandt, um die Ausdehnung und die zeitliche Entwicklung der Auflockerungszone (EDZ) zu bestimmen. Es werden die Vorteile und Grenzen des Modells diskutiert.

Jan 1, 2003

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By G. H. Lind

This paper discusses the traditional costing approach currently used in the underground coal mining industry. Activity Based Costing (ABC) is identified as being a potentially more effective manner in which to cost underground coal mining systems. With the use of a costing framework developed by the author incorporating new thinking to eliminate the shortcomings identified in the traditional costing approach, a comparison of two types of underground coal mining systems, viz. continuous miner and longwall, is conducted. It is found that under certain criteria, in all cases, irrespective of the way in which the systems are costed, the continuous miner system is currently the better investment. It is also observed that when a system is costed using ABC that better investment decisions result when compared to costing the same system using traditional costing techniques. It is further seen that traditional costing techniques tend to overestimate the total costs of a mining system. This paper shows one application of ABC that can be incorporated as a management tool.

Jan 1, 2001

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005