Search Documents

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

At Namdeb, submerged beaches are earmarked for sampling and future mining and various sampling configurations are tested for optimality through the use of spatial simulations. For the creation of these virtual orebodies, basic statistics and variograms are needed, but in this specific instance no data exists from which the necessary parameters can be determined. The best that can be done is to use proxy data from onshore beaches, with adaptations where needed. The reworking of raised beaches during periods of rising and falling sea levels in some cases destroyed the internal beach structures, and it is very difficult to determine the variograms. A method is proposed whereby simulated annealing is used to adjust the sample locations to align the data pertaining to beach crests or cliff lines, thus improving the variogram structure along the shoreline in the direction of the highest geological continuity.

Jan 1, 2014

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By K. Cole, D. Mesa, P. R. Brito-Parada, M. R. van Heerden

Turbulence in stirred tank flotation vessels determines the bulk transport of particles and has an important role in particle-bubble collisions necessary for attachment. Positron emission particle tracking (PEPT) produces quantitative measurements of the kinematic motion of different particle classes inside flotation vessels. This paper presents flow profiles of the vessel, residence time distributions, flow profiles through the mesh and macroturbulent kinetic energy distributions as experienced by valuable (hydrophobic) mineral particles in a laboratory scale flotation vessel. The results highlight the impact of the rotor-stator design and a retrofit mesh modification at the upper part of the vessel which improve recovery by decreasing turbulence in the quiescent zone and at the interface. Keywords: Flotation machines, turbulence, PEPT

Jan 1, 2020

By M. -A. de Ville d’Avray, J. Bosman, S. Brochot

Dense Medium Separation (DMS) technologies are used for light (coal, lithium) or heavy (chromite, iron ore, diamonds) minerals concentration, but also for ore pre-concentration (Pb/Zn) or waste (plastics). Dense media are mainly formed from a suspension of magnetite or ferrosilicon in water. Such DMS circuit design or optimisation requires a full and detailed material balance which can be obtained by the aid of modelling and simulation tools. This balance is not limited to ore and its valuable minerals, but also the recovery of the dense medium itself. If the density is the main property used for separation, the particle size plays a non-negligible role, and, more precisely, the liberation classes which can be associated to the washability curve. The paper presents how the modelling and simulation platform USIM PAC can answer this challenge with the set of models for DMS operating units such as drums or cyclones, and their associated screens (drainage, rinsing) and magnetic separators for medium recovery. Some examples for mineral concentration will illustrate this approach. Keywords: Process simulation, process modelling, dense medium separation, process optimisation

Jan 1, 2020

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By G. Chambovet

Applied geophysical methods such as the surface seismic method have been applied for many years and in many places, mainly for oil exploration and to a lesser extent for mineral deposits? exploration in sedimentary basins. The seismic method fundamental is based on the variations of acoustic impedance in a layered earth model and such variations at each main geological interface create reflected waves that are processed and imaged in order to output a clear picture of the subsurface structure. The geology of South Africa was historically, and even until recently, considered as unfit for seismic exploration and the mines were always reluctant to spend any portions of their exploration budgets on these techniques. Hard rocks and high P-waves velocities were creating quite a hopeless model for any mine geologist or geophysicist (if any), unsuitable for the proper use of seismic waves to image their subsurface problems. Boreholes were considered the only reliable tool to derive a geological image of the mine structural features and were linked sometimes with surface methods such as aero-magnetism. The obvious flaw of this methodology was the inability to derive a continuous image from a discrete set of measurement points. Surface 3D seismic is the tool that gives a reliable solution from the initial model extracted from the boreholes, as even the aero-magnetism mapping gives a flat image, unable to show any depth correlation from well to well. The first 3D surface seismic surveys were recorded in the early Nineties only for the gold mines of the Witwatersrand, after a series of serious new shaft sinking failures. The wrong geological locations of these shafts resulted in financial loss of several hundred million rands. The era of3D seismic just started in South Africa and till 1997, all seismic done in the country was for gold exploration with geological target depths close to the oil exploration average depth of investigation. A very important breakthrough was reached when the depth accuracy of the seismic image was tested in real scale as the stopes were surveyed. An error of amplitude of 20 m was usual when true depth was compared with the seismic image predicted depth and shape. This accuracy, completely unknown in oil exploration, started to gain supporters of seismic methods in the mining community but the cash problems and the concentration/disappearance of gold mines in the late Nineties, led to the belief that seismic would be just a very short exploration activity for the mining sector. ort exploration activity for the mining sector. But starting in 1998 with Impala, a tremendous and continuous 3D surface seismic activity occurred in the platinum mining sector. The seismic world got used to new terms such a Merensky and UG2, which have replaced the VCR and black reef. If the primary expectation of platinum surface 3D seismic was to determine and ascertain new shaft locations, as for the gold mines, the quality of seismic data led the mine geologists to require smaller and smaller imaging of geological objects. In addition to the main structural image, small faults, potholes, and shear zone were common expectations of platinum seismic. In a constant velocity environment, what saved the day was the sharp density contrast between the PGM reef and the embedding geology. A good contrast of impedance exists in the whole Bushveld and is sufficient to have enough reflected waves from the PGM main layers to build a high quality seismic image of the subsurface. Recent advances in technology have led in less than 10years to major improvements in the seismic acquisition by using high frequency vibrating seismic sources, but also in processing and interpretation. With these latest improvements, seismic can detect objects of 7.5 m size, either fault throws, flexures, etc. The PGM formations of the Eastern limb of the Bushveld Complex are now accessible for seismic imaging, with cost per square kilometre comparable to the borehole cost of the same surface unit. The economically acceptable seismic surveys can be used for UG2 structural imaging up to a depth of 210 m below surface. Linked with borehole information, 3D seismic today offers a wide range of information for mine development: structural imaging, small fault detection, pothole and shear zone identification. All users of 3D seismic have also used this technique as a tool in the process to qualify their mineral reserves and especially from the category ?inferred? to the category ?measured?. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. The current high demand on platinum, pushes the seismic towards new technologies to be implemented in order to improve the final image. Using surface and borehole seismic together or acquiring seismic surveys with multi-component receivers have been just introduced in South Africa. In less than 10 years, surface seismic by adapting its methods to the special case of the Bushveld, became a mandatory step in mine development and ore resources evaluation. As part of the ?seismic? world we are proud to be a major player the ?surge? of platinum exploration and production in these last years and we will certainly increase our synergy with the mine sectors in the exciting coming years.

Jan 1, 2006

By P. T. L. Koh, M. P. Schwarz

A series of parametric studies were carried out for a flotation cell using computational fluid dynamic (CFD) modelling to determine the local response of hydrodynamic performance measures to change in operating conditions. As an example, an Outotec cell was used to carry out the response analysis. The hydrodynamics of the flotation cell has been previously investigated by laboratory measurements presented by Schwarz et al (2019), and a CFD model of the cell was developed and validated using these measurement data (Schwarz et al., 2019). In this work, parametric studies have been performed by modelling the flotation cell at different stirring speeds and gas flowrates, varying above and below standard conditions. Predictions of void fraction, bubble size, bubble surface area flux and particle–bubble collision rate are presented showing the effects of increasing and decreasing stirring speed and gas flowrate around the base case. Generally, the total gas holdup in the flotation cell was found to increase with increasing gas flowrate. The bubble diameter was found to decrease with increasing stirring speed and increase with increasing gas flowrate. The collision rate increased with both stirring speed and gas flowrate. The parametric results show that there is a correlation between the bubble surface area flux Sb which is affected by stirring speed and gas flowrate, and the particle–bubble collision rate. With the collision rate as an indication of flotation collection, it is also possible to show that cell performance can improve more by increasing stirring speed than by increasing gas flowrate in a situation where everything else remains constant. The CFD results can form the basis for a Response Surface Method (RSM) analysis which can then be used for automated optimization of cell performance. Keywords: Flotation kinetics, computational fluid dynamics, bubble surface area flux, particle-bubble collision rate

Jan 1, 2020

By N. Thorp, S. J. Bluhm

It has long been recognized that the provision of an acceptable thermal environment minimizes the danger and the adverse effect of heat stress, which is directly linked to decreased productivity, increased accident rates, and excessive physiological strain in workmen. Refrigeration in one form or another helps to provide this acceptable thermal environment. This paper outlines the problems encountered in a working area, and the steps taken to alleviate environmental conditions in some stopes with the introduction of selective cooling employing small water-chilling units in conjunction with specially designed stope coolers. Performance figures are given for plant and stope coolers, and the effectiveness of the system is assessed from an evaluation of the improvement achieved in the environmental conditions.

Jan 1, 1986

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"The primary function of a tundish in the steelmaking industry is to serve as a buffer tank, accepting molten steel from the batch ladle process and allowing it to be cast continuously. However, modern steelmaking has more stringent demands for the quality of the steel product, requiring increased control over the properties of the molten steel before casting. For this reason tundishes have been developed as metallurgical reactors to serve as the final step in refining of the molten steel by removing non-metallic inclusions, preventing the formation of new inclusions, and promoting chemical and thermal homogeneity. In this study the flow behaviour in a four-strand tundish was investigated by means of a half-scale water model as well as numerical modelling. Both the numerical study and physical model were used to characterize residence time distribution (RTD) in the vessel and calculate properties pertaining to the tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices was prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing short-circuiting and provided surface-directed flow, which aids inclusion removal in the slag. Despite the benefits of the use of turbulence inhibitors, it was observed that the upward-directed flow increased the maximum turbulence kinetic energy near to the surface by approximately 120% compared with the bare tundish. Therefore the potential for slag entrainment should be considered during the design and operation of tundishes utilizing turbulence inhibitors."

Jan 1, 2014

By F. Dutoy, M. B. Stella, C. F. Carrozza

Rare earth elements (REEs) are indispensable components in the manufacturing of high-tech devices, renewable energy technologies, and defence applications. As global demand for these elements continues to rise, there is a pressing need to optimize extraction processes for both efficiency and environmental sustainability. This study explores approaches to rare earth extraction using Ionquest® 801 and integrates a predictive modelling to enhance process understanding and optimization. We conducted a screening test varying pH process to evaluate the best extraction efficiency. Starting pregnant leach solution (PLS), solution was prepared in the lab with the following rare earth elements: La, Ce, Gd, Dy, and Υ, at 0.02 M for each element. The data obtained were used to develop empirical and mechanistic models to predict rare earth extraction yields and flowsheet. Further tests were performed by mixing specific concentrations of different extractant and/or phase modifier. Our experimental results demonstrated the effectiveness of the proposedextraction methods, highlighting improvements in both yield and selectivity. The developedmodels successfully captured the complex relationships between process parameters and extraction efficiency, providing valuable insights for process optimization.

Nov 6, 2024

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By K. Shame, H. H. Thiele

South Africa holds approximately 70% of the world’s total chrome reserves. Chromium is an important raw material for the production of stainless steel and ferrochrome alloys. Over the years, China’s ferrochrome market has been dependent on chrome ore imports from South Africa. In 2018, China imported about 75% of its chrome ore from South Africa. With the low platinum price and the rising demand for stainless steel, a growing demand to evaluate new beneficiation technologies for fine chromite was identified. Gravity separation of fine chromite (<75 μm) is inefficient, due to the limitations of the technology to upgrade fine particle size distributions. Potential for the recovery of chromite, specifically fines (<75μm), lost to UG2 PGM flotation tails, but also from MG and LG6 spiral circuit tailings exist. Flotation of podiform chromite ores from India and Kazhkhstan is successful in generating saleable product grade, following acid or alkaline flotation routes. Application to South African stratiform chromite is being evaluated, with the emphasis on evaluating reagent type, optimising dosages and the effect of pH in optimising flotation performance. Flotation can unlock additional value from chromite tailings material. The effect of ore characteristics such as gangue mineralogy, particle size distribution and headgrade are reported. The performance in terms of product quality and yield are evaluated and compared. The impact of this paper will not only prolong life of mine and increase revenue but will also alleviate environmental burdens associated with tailings dams. Keywords: Chromite, flotation, fine material, performance optimisation

Jan 1, 2020

By M. C. Bekker, T. Govindasamy

The potential benefits of implementing the Last Planner System (LPS) on mining infrastructure projects were explored through two case studies in the South African mining industry. The first part of the study involved measurement of the impact of LPS through earned value techniques on secondary project data. The second part sought to establish the lean construction success factors leading to improvements in construction performance. This was done by means of a research questionnaire distributed to the project owner’s teams, contracted parties, and the LPS facilitators. The results revealed a positive correlation between LPS application and planned percentage complete. However, the performance achieved during the LPS pilot was not sustained. The success factors and benefits considered most evident in the case study pilot differed among the three stakeholder groups. The findings are expected to guide construction stakeholders to better define performance measures and focus on factors required to make LPS implementation more effective in the South African mining sector.

Feb 12, 2024

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By S. Ata, Y. Pan, S. Gautam, G. Bournival

Bubbles play a vital role in flotation, and their properties directly affect the flotation performance. Xanthates are one of the major collectors used in sulphide mineral flotation. It is often believed that their main function is to render the desired mineral surface hydrophobic, which is essential for the mineral particles to attach to air bubbles. This paper takes a systematic approach to assess the influence of potassium amyl xanthate (PAX) at the air–liquid phase and its interaction with the frother in the concentration of range 10–5×104 ppm. Bubble size was measured in a laboratory flotation cell using a photographic technique and the stability of bubbles was quantified in terms of coalescence time -, the time required for a bubble pair produced at adjacent capillaries to merge into a single bubble. Bubble size reduction of up to 26% was observed with increasing PAX concentration in the cell. The bubble coalescence experiments using PAX only showed that the bubbles coalesced quickly at lower concentrations (10–50 ppm), but they stayed extremely stable at higher concentrations (1×102–1×104 ppm). Further experiments were carried out where the concentration of PAX was fixed at 1 ppm and 4- Methyl-2-pentanol (MIBC) concentration was varied. The synergetic action of PAX and MIBC significantly improved the stability of bubbles in the mixed system, and is even compatible with a stronger frother. The results strongly suggest that the role of PAX at the air–liquid phase should be considered in the practice of sulphide flotation. Keywords: Bubble size, bubble coalescence, PAX, bubble stability

Jan 1, 2020

By C. C. Pretorius

3D seismic surveys have become a well-accepted method of imaging sub-surface geology in the Bushveld Basin. Because both the seismic sources and receivers are placed at surface, most surveys are limited to imaging faults with >=7 m throw. However, some areas such as shaft infrastructure can benefit from the ability to detect smaller structures prior to shaft sinking. Borehole radar and logs such as the acoustic televiewer can identify these structures in the shaft barrel, but not within -200 m from the shaft. Therefore, Anglo Platinum has developed the method of high-resolution 3D vertical seismic profiles (VSPs) for structural sterilization of shaft sites prior to shaft sinking. VSPs utilize a surface source and sub-surface receivers deployed down a borehole. This means that seismic energy goes through the near surface only once, and therefore suffers less frequency loss than when both source and receivers are on surface. Furthermore, VSPs can record 3 component (3C) data which comprises P wave, Sh (horizontal) and Sv (vertical) wavemodes. Because S waves travel at about 0.6 of the velocity of a P wave, shorter wavelengths and therefore higher resolutions are possible using S wave data. VSPs were first used in their one dimensional, zero offset, mode to correlate borehole geology with seismic stratigraphy within seismic surveys. This showed that VSPs record -30% higher frequencies than surface seismic surveys. The program then applied two dimensional VSPs to the problem of imaging geological structure close to a borehole. 2D VSPs confirmed that high frequency results could be achieved, and that this enabled a more accurate image of the Merensky Reef than could be achieved by surface seismic data. Finally, the program has achieved the successful recording and processing of 3D VSP data, with both compressional and shear wavemodes giving a high resolution structural result. Although P wave data gives -30% frequency improvement over surface seismic surveys, S wave data can give as much as 80% improvement, further improving the structural image achieved. The high fixed costs of VSP surveys mean that they should ideally be run in multi-client batches, which can reduce the per borehole cost by up to 50%. Their application is anticipated to be on high value capital infrastructure with a geological risk from faults which are not imaged by surface seismics-generally in the sub-7 m range. Keywords VSP, 3D seismic, bushveld, platinum, resolution, imaging, shear waves, shaft sinking.

Jan 1, 2011