Search Documents

By J. P. Hugo

Nuclear energy - its interactions with mining and metallurgy - PRESIDENTIAL ADDRESS given by J. P. Hugo Pr. Eng., B.Sc (Eng.) (Rand), Ph.D. (Sheffield) Energy is the life blood of the modern technological era in which we live and it was, I think, Benjamin Franklin who said that the manipulation of energy was the basis of all science and technology. This is perhaps an oversimplification, but there can be little doubt that our life today, and the improved standard of living we aspire to, are governed almost entirely by our ability to generate and manipulate energy. This ability has made it possible for Man - each specimen a feeble twentieth of a horsepower - to travel to the moon, to recover valuable minerals from the depths of the earth, to do arithmetic at unbelievable speed, to lessen the drudgery of manual labour. For these and virtually every aspect of our life we are dependent on energy from external sources. It is, therefore, not surprising that the per capita consumption of energy, and more particularly electricity, has become one of the most reliable criteria by which to measure the standard of living and technological advancement of a country.

By S. V. Mkhatshwa

The purpose of the study was to investigate the factors which affect the performance of the loading and hauling fleet and also find possible solutions to eliminate these factors, so that the daily tonnages required could be produced .This is due to the high demand of manganese required by clients. The investigation strongly focuses on the performances of the three 777D Caterpillar trucks and the R984 C Liebherr Litronic Hydraulic Excavator. In the content of the study, these machines are used to remove and move the low grade manganese (also known as the top cut overburden) in order to expose the high grade manganese from north pit to dump 4. The objectives of the project were to determine the actual performance of the loading and hauling fleet per shift, compare the actual and the theoretical performance and identify areas that need to be improved. To achieve the goals set for the project, a number of activities were carried out. ?Perform a time study to compare the performance of the loading and hauling fleet with the manufacturer specifications ?Match the equipments analysis for Loading and hauling ?Road conditions analysis ?Rolling resistance and Road Gradients analysis ?Operating cost analysis.

Jan 1, 2009

?Longhole blast hole drilling? techniques are not new to the mining industry. Appropriate mechanization and improvement of the techniques and application has evolved from the industry requirements. Today safety and economics play a larger role in the excavation of ore passes, ventilation passes, and relatively small inclined excavations in the conventional gold and platinum industry. The application of dropraise drilling from the top or from the bottom is discussed investigating the current techniques available, DTH application, advantages and disadvantages, limiting factors, typical layouts and proposals, the drop raising technique and future applications. Similarly, the application of longhole blast hole drilling in tabular and massive orebodies is discussed with emphasis on the DTH application, advantages and disadvantages, limiting factors, typical layouts, the long hole stoping techniques and future applications.

Jan 1, 2003

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By M. Bryson, G. Marap, M. Ntlhane, M. D. Hlahane

This study investigated flotation of phosphate from a low-medium grade 8-12% P2O5, 65-73% SiO2 sedimentary phosphate ore from Kropz Elandsfontein (herein referred to as Elandsfontein) in South Africa. Quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) was used to determine apatite grain size distribution, liberation and mineral association in the F2 horizon sample. The mineralogy indicated that apatite was liberated and for the Elandsfontein plant to operate at the design throughput, the flotation feed has to be milled to a coarse grind ranging between 300 μm and 425 μm. Reverse flotation process routes using varying reagent dosages, and flotation feed top sizes that could possibly yield a final product of 31% P2O5,10% SiO2 at a reasonable +70% P2O5 recovery were investigated. Based on the results, a split circuit of coarse (-300+212μm) flotation and fine (-212+20μm) flotation, was mostly preferred as compared to treating the whole ore. A final combined concentrate of 31% P2O5 and 10% SiO2 with P2O5 recovery of 84% could be produced from the reverse split circuit. The robustness of reverse flotation for both coarse and fine fractions was further investigated. Reverse flotation of the fines fraction was found to be robust and produced a final product of 31% P2O5. It was however more challenging to achieve the required product grade and recoveries on the coarser fraction (-425+212μm), suggesting that reverse circuit was not adequately robust at fractions coarser than 300μm. Keywords: Phosphate, sedimentary, reverse flotation, particle size

Jan 1, 2020

By F. Magweregwede, S. Khan

Circular economy opportunities for the mining sector are presented in this paper. A literature review was undertaken, followed by qualitative data gathering through survey questionnaires and unstructured interviews, and stakeholder engagements through workshops. The circular economy opportunities were identified and categorised according to the three circular economy principles of designing out waste and pollution, keeping products and materials in use, and regenerating natural systems. Opportunities aligned with the first principle include increased ore extraction efficiency processes, water recovery and recycling, substitution of raw materials, technology and waste utilisation for carbon capture and biotechnology. The second principle includes opportunities such as zero waste-to-landfill strategies, repurposing of mine waste, re-mining of tailings, recycling metals and processing of residues, and urban mining of electronic waste. Opportunities aligned with the third principle include the adoption of renewable energy, green hydrogen production, repurposing of post mining landscapes, and eradication of alien invasive vegetation. Furthermore, the challenges of implementing circular economy in the mining sector are discussed. The current rate of waste generation from mining activities far exceeds the rate of reuse and repurposing. Recycling of large tyres and characterisation of hazardous electronic waste also pose challenges. The most implementable circular economy opportunities in the mining sector are those aligned with the second principle of keeping materials in use. The high impact opportunities aligned with the first principle of designing out waste and pollution, and the third principle of regenerating natural systems, are more difficult to implement as they require large investments.

Dec 15, 2025

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

By S. Durapraj, R. T. Masethe, U. Maqina, A. C. Adoko

This study investigates seismicity and rockburst control within the Merensky Reef and UG2 orebody of an intermediate-depth platinum mine located in South Africa's Bushveld Complex. Utilising a mine-wide seismic monitoring system, over 1,900 seismic events were recorded between April 2023 and May 2024, revealing complex seismic patterns driven by mining-induced stress changes. The largest event, with a magnitude of ML 2.0, underscores the seismic risks associated with mining at increasing depths. Key findings include the spatial and temporal variability of seismic events, with high seismic activity observed near pillars and geological structures. A significant portion of events correlated with pillar and foundation failures. Moment tensor analysis identified dominant failure modes, such as stress-driven fracture closures and dynamic pillar failures. To mitigate risks, the study emphasises advanced support system redesign and rockburst risk assessment using the rockburst damage potential (RDP) method. The research highlights the importance of monitoring, geotechnical compliance, and adaptive designs in enhancing safety and reducing seismic hazards in underground mining operations. The study applied the RDP framework, classifying damage across R1 to R5 scales, where most instances fell into low-risk categories (R1 and R3), indicating minor to moderate damage. However, data limitations and the tabular stoping method's complexity led to inconclusive results, highlighting the need for more robust data and customised risk assessment tools. Despite these challenges, the RDP approach provided valuable insights into rockburst mechanisms and the effectiveness of existing support systems.

Jan 12, 2025

By K. Harlow

"Zircon is a naturally occurring radioactive material (NORM) and as such is subject to a variety of regulations around the world. The regulatory processes and their implementation are summarized and the key issues affecting zircon and zirconia highlighted. Having absorbed the activities of the former Zircon Minerals Committee, the strategy of the Zircon Industry Association (ZIA) is to be the ‘go-to place’ for information on these matters, and its activities in the NORM space are described. Chemical industry regulations such as REACH are spreading around the world, and the paper provides an update of their status in the key jurisdictions. As mineral sands are transported to market in oceangoing vessels, they are subject to the regulations of the International Maritime Organization, which are summarized in the paper. IntroductionFrom a global perspective, zircon is generally not found in high concentrations other than in placer and dune deposits where it has been deposited along with other heavy minerals such as ilmenite, rutile, and monazite. Such deposits have been sorted and concentrated over geological time by the action of tides, waves, and wind to form concentrated deposits of heavy minerals along old coastlines and in river beds and deltas. Consequently, zircon is mostly found in association with the principal titanium minerals ilmenite and rutile. These secondary concentrations in placer deposits provide the commercial sources of zircon.All geological materials contain natural radioactivity, although the term NORM (naturally occurring radioactive material) is mostly used for minerals and other materials with above-average uranium and thorium concentrations. Importantly, the radioactive nature of zircon has not changed, but the way in which radioactivity is viewed by regulators has, affecting the zircon industry throughout the value chain."

Jan 1, 2017

By N. Sinclair

"In open pit dozer bulk push operations, the material left resting against the highwall after blasting poses an issue. This is because dozers cannot physically get in behind the waste to begin the bulk pushing process. Instead, an excavator can be used to side-cast this waste for the dozers to access. An alternative technique is to have the dozers ‘side-cut’ the material, which involves the dozers running parallel to the wall, digging out the material, and eventually rotating their blades to begin bulk pushing. Industry practices suggest the latter technique is less productive and economical than using an excavator. However, such excavator sidecasting ‘economic viability’ assumes that smaller/ancillary type excavators are used (i.e. less than 23 m3 bucket capacity). So, what happens if some mine sites are restricted to using relatively larger excavators (> 23 m3 bucket) that are preferred for higher priority digging tasks? When can they avoid using their excavator? This paper explores multiple scenarios that have been designed and developed to simulate data results, which identify conditions in which the dozer side-cutting technique becomes more economically viable than excavator side-casting in terms of decreased unit cost per loose cubic metre. IntroductionOptimizing the cost of waste removal operations is important for the profitability of opencast coal mines. In the past decade, dozer bulk pushing has emerged and taken over from traditional waste removal operations such as dragline and truck-and-shovel methods at various sites around the world (Beatty, 1994). In a typical bulk push operation, once the bench has been blasted, waste is left resting against the highwall, which can either be cleared using a loading unit or by having the dozers ‘side-cut’ the highwall.Dozers perform most effectively when slot dozing side-by-side, perpendicular to the highwall. However, when dozers are required to remove material off the highwall, they must push parallel to the highwall, rather than perpendicular, hence ‘side-cutting’ the material to ensure a clean face. While dozer sidecutting is possible, it has been found that the majority of mine sites use a loading unit in this situation to avoid dozer inefficiency. Other perceived issues with dozer side-cutting include higher maintenance requirements and safety risks to dozer operators working in close proximity to the highwall."

Jan 1, 2019

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By M. C. van Eeden, R. Vermeulen, K. B. Le Bron

This paper presents the lessons learnt during the transition from an open pit method to a sub-level open stoping method at the Koidu Limited kimberlite pipe. These learnings may assist other mines with planning, both from a practical implementation perspective (layout, charging up challenges), and a method for estimating potential dilution and stability challenges associated with the interaction between the surface and underground excavations. Predictive geotechnical stability modelling was successfully applied to highlight potential failure zones, which allowed modification and enhancement of the mining layouts and quantification of the potential dilution of the kimberlite from indicative instabilities.

Sep 1, 2025

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By G. Akdogan, Q. G. Reynolds, S. J. Baumgartner

A computational model of a submerged arc furnace (SAF) used in the production of ferrochrome is presented. The model‘s intended use is to investigate the extent to which intrinsic and extrinsic properties of the raw materials affect burden distribution and electrical resistance within the furnace. The model is built on the discrete element method and calculates the mechanical interactions of particle distributions resulting from the flow motion of typical raw materials used in the smelting of chromium ore. This model excludes the effects of thermodynamics, furnace chemistry, and heat transfer. It illustrates how the consumption of materials (chromite pellets, flux, and reductant) is affected by changes in electrode length, reductant fractions, and reductant sizing and density during the formation of a reductant bed. The resistance calculation algorithm developed by Mintek was applied to construct networks developed from particle contacts, which can quantitatively generate estimates of the electrode-to-electrode and electrode-to-bath electrical conduction conditions.

Apr 16, 2024

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

By H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2008

By K. Nong, H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2007

By T. P. Letsebe, L. Magwaza, T. A. Sethu, S. M. Rupprecht

"The authors were tasked with introducing safe and efficient drilling and blasting practices to a small artisanal mine located in the Eastern Province of Rwanda. The current mining methods employed at the mine are inefficient as rockbreaking is conducted utilizing hammer and chisel, or by drilling and blasting with no understanding of the rockbreaking process. The paper discusses the drill and blast cycle, as well as the associated activities necessary to support the mining cycle. The challenges and critical aspects in implementing drill and blast activities are discussed, as well as some of the technical aspects, i.e.drilling pattern, initiation and timing of the blast, and handling of misfires. Ancillary issues such as ventilation, training, communication, effective planning, logistics, and human relations are also examined. IntroductionRockbreaking accounts for 60% of the direct mining costs in small-scale mining. When drilling and blasting practices are poorly implemented the process becomes inefficient and dangerous. The introduction of a proven drill and blast system to artisanal mining offers a number of challenges, with safety being considered the backbone of any sustainable operation and a standard that cannot be compromised.The paper is based on a project at an artisanal cassiterite (tin) mining operation in a small village in the Kayonza District in the Eastern Province of Rwanda. A drill and blast programme utilizing industry best practice was introduced at an underground development end; a raise developed at an inclination of 23 degrees. The underground working is accessed via a 17 degree incline shaft with an operating length of 105 m and serviced by a single drum winder. The winder operates at a speed of about 3.5 m/min hoisting two 1 t wagons from the bottom of the incline to surface for tipping (Figure 1)."

Jan 1, 2017

By S. J. Baumgartner

The ferromanganese industry is under pressure to deal with the slag arising from the production of ferromanganese, which is discarded in landfills or slag heaps. This material poses an environmental and health risk to surrounding ecosystems and communities, and disposal costs are increasing. Ferromanganese slag contains an appreciable amount of residual manganese metal, which can be exploited. Previous work has shown that the slag can be leached fully, while rejecting the silica to a residue. The methods that were investigated to recover manganese from the leach solution included hydroxide precipitation to upgrade the leach solution followed by manganese carbonate precipitation to produce a pure manganese carbonate product or a manganese carbonate furnace feed material, which would be recycled to increase manganese recoveries in the production of ferromanganese. In addition, electrowinning of electrolytic manganese dioxide from the leach solution was studied. The methods were compared in terms of selectivity, costs, and product quality. Co-recovery of the leach residue, which is a potential cement additive, is discussed. Among the methods investigated to upgrade the pregnant leach solution, hydroxide precipitation utilizing ammonia to adjust the pH appears to be the most effective in removing major impurities such as iron, aluminium, and silica to less than 1 ppm. The manganese carbonate and impure manganese carbonate furnace feed products met quality specifications. However, although the production of these materials was technically viable, the large amounts of base reagent that were required to raise the pH, and the associated high operating costs, rendered the process uneconomic. An optimization study was therefore carried out with the primary objective to determine the ideal acid amount to be utilized in the waterstarved digestion stage, thereby decreasing acid and base consumption while optimizing the quality of the pregnant leach solution, and producing a leach residue that contained <1% Mn. The outcome was an economically viable process. Additional benefits included an increase in the manganese content of the impure manganese carbonate furnace feed material, and a substantial reduction in the dilution of the pregnant leach solution, thereby maintaining high manganese concentrations that rendered the solution viable for electrowinning of electrolytic manganese dioxide, the production of which yielded a current efficiency of 74%.

Jan 1, 2014