Search Documents

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

Your Council has pleasure in submitting its report for the year ended 30th June, 1969. COUNCIL The following served as Office Bearers during the year under review: Messrs. R. C. J. Goode (President), J. K. E. Douglas and V. C. Robinson (Vice-Presidents), P. Lambooy (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Messrs R. J. Adamson, M. Barcza, F. P. Bath, Or J. M. Bereza, Or W. Bleloch, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, A. E. Gilfillan, G. W. Holl, Prof D. D. Howat, Or J. P. Hugo, Messrs C. J. Irving, D. M. Jamieson, J. G. Kirchner, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Or J. T. McIntyre, Mr J. A. Nixon, Prof R. P. Plewman, Messrs J. F. Reid, H. Simon, C. G. Sowry, W. T. Stobart and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of eighteen. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R2,124, compared with an excess of income over expenditure of R4,218 last year. There are a number of reasons for this substantial change. There was a loss on realization of investments compared with a substantial surplus in recent years. The publication of the Journal once again resulted in a large loss in spite of a generous subvention of R2,000 from the Department of Cultural Affairs and other assistance amounting to R750. The revenue from sales of publications was down considerably. This is a figure which fluctuates considerably from year to year. The secretarial fee was considerably higher than previously. Due to pressure of work it was necessary for the Secretary to relinquish his duties with the Institute of Land Surveyors and, therefore, for this Institute to assume the additional staff costs involved. Finally there was unusual expenditure on the 75th Anniversary celebrations. There was a pleasing increase in revenue from subscriptions, due to the steadily increasing membership, but this was quite inadequate to cover the substantial increases in expenditure and losses in revenue mentioned above. The changes that have been effected in the arrangements for the publication of the Journal have been mentioned elsewhere in this report. It is expected that these will bring about substantial financial benefits in the long term. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of Rl00 and the total fund was therefore increased by this amount to R4,206. The balance sheet indicates that the market value of quoted shares and debentures increased during the year from R8,755 to R13,059, while the Accumulated Funds now amount to R22,567 as against R24,691 last year. MEMBERSHIP Fifty-six Members, fifty-five Associate Members, thirteen Graduates, twenty-two Affiliates and twenty- nine Students were elected during the year. Twelve Members were admitted to Life Membership; seven Associate Members were transferred to the grade of Member; four Graduates and two Students were transferred to the grade of Associate Member; five Students were transferred to the grade of Graduate; three Affiliates were transferred to the grade of Member; five Affiliates were transferred to the grade of Associate Member. Three Members, seven Associate Members, two Graduates, two Affiliates and six Students were removed from the Membership Roll in terms of By-Law 7.7.1. Your Council records with deep regret the death during the year of the following members: E. F. J. Bulman (Member), E. F. Chapin (Member), R. A. H. Flugge-de-Smidt (Hon. Life Member), T. S. Haldane (Member), J. M. Massie (Associate Member), S. W. Page (Student), S. R. Rabson (Member), M. Ramsay (Member), F. Wartenweiler (Hon. Life Member). A comparative statement of the membership as at 30th June, 1969, and the end of the previous year is shown in the following tabulation: 30th June 30th June 1968 1968 Honorary Life Members 12 10 Honorary Members 6 6 Life Members 176 189 Members 488 514 Associate Members 409 448 Graduates 60 68 Affiliates153 155 Students152 162 1,456 1,552 PAPERS AND JOURNAL The Institute is changing the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. In making this change it will conform to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Engineering Institutes. In making these changes the opportunity was taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Presidential Address by Mr R. C. J. Goode and twelve papers which were published in the Journal during the year are listed below: August, 1968: Presidential Address: "The Institute-In retrospect and prospect." September, 1968: "Rotary mill liner practice in the South African gold mining industry," by J. H. French and O. E. Lissner.

By J. H. Maritz, Uludag. S.

"*Paper written on project work carried out in partial fulfilment of B.Eng(Mining Engineering) degreeAfriTin Mining Limited plans to reopen the Uis tin mine in Namibia and establish a pilot processing plant for phase 1 of the Uis tin project, which is scheduled to commence in the last quarter of 2018 . A mining plan is required for phase 1 to supply the new pilot processing plant with 500 kt of run-of-mine ore per annum, for a period of 5 years. New geological mapping and three-dimensional modelling of the mining area were utilized to identify the most optimal mining locations that require low initial waste stripping. An open-pit mining method was selected to target the surface outcrops of the pegmatite orebodies. The mine design criteria were determined and used as input to generate the mine design by utilizing professional engineering software. The mine design was optimized and an overall stripping ratio of 0.81 was achieved. A 5-year production schedule was developed for the mine design according to quarterly periods of three months. A fixed production target of 125 kt of ore was assigned to the quarterly periods, and a ramp-up production target of 65 kt of ore was assigned for the first period. The mobile mining equipment requirements were calculated, and recommendations were made for implementing the 5-year mining plan. IntroductionAfriTin Mining Limited is the owner of the Uis tin project in Namibia and plans to reopen the Uis tin mine, which is located near the town of Uis, approximately 164 km north of Swakopmund. The Uis tin mine was owned and operated by Imkor Tin, a subsidiary of Iscor South Africa. Mining commenced in 1958, and the operation was closed in 1991. Steffen Robertson & Kirsten (SRK) defined the life of mine (LOM) plan for the historical Uis mine in 1989. The SRK report estimated the historical resources and reserves, which consisted of sixteen cassiterite-bearing pegmatite orebodies. SRK developed the most economical pit designs to provide the highest average tin grade at the lowest practical waste stripping ratio. Exploration data from the SRK report of 1989 was used extensively throughout this study, since no new exploration drilling has been conducted. The pegmatites are present as large, subvertical and outcropping veins up to 100 m in thickness. Once phase 1 is operational, mining will be conducted using conventional open pit mining methods. Initial production will be from exposed pegmatite veins in the old mine workings. AfriTin plans to establish a pilot processing plant by the end of 2018 to beneficiate run-of-mine ore at a rate of 500 kt per annum."

Jul 1, 2019

By J. W. Joubert, R. C. W. Webber-Youngman, M. D. Budeba

"SynopsisCost estimation for surface coal mines is a critical practice that affects both profitability and competitiveness. New mines require these costs to be estimated using available information before a project begins. The competitive advantage of a new mine depends on it being both efficient and cost-effective. Low-cost producing mines have a higher chance of survival in a low-price environment than do high-cost producers. The competitiveness and profitability of a coal mine is based on the costs of production and the supply position on the cost curve. There is no single method of cost estimation, and the available methods consider only one or a few variables, leaving out multiple variables that could significantly affect the estimation of mine costs. Mining companies are thus searching extensively for a method that will increase accuracy in the estimation and evaluation of mining projectsThis paper highlights the shortcomings of the available approaches and proposes a data envelopment analysis method to develop a frontier for effective surface coal mines, and the use of a parametric method for modelling the costs and productivity of new mines to ensure effective competitiveness. The models will extend the capability of estimation and the accuracy of estimates using the efficient decision-making units, by considering the optimal mine-specific and external variables affecting costs.IntroductionCoal contributes 25% of the world’s primary energy needs, after fuel oil, which contributes 35%. The world energy demand, estimated over the period 1990 to 2030, is expanding at a cumulative annual growth rate (CAGR) of 1.7% (Schernikau, 2010, p. 14). This emphasizes the need for enhancing the production of existing mines, as well as opening new mines in order to increase the supply of coal."

Jan 1, 2015

By S. Ndlovu, M. Malatse

"The Witwatersrand Basin is the heart of South Africa’a gold mining industry. The cluster of gold mines located in the Witwatersrand Basin generates a significant amount of mine tailings, which have adverse effects on the environment and ecological systems. In addition, disposal costs are very high. The exponential population growth in the Witwatersrand area has resulted in pressure on the reserves of traditional building materials. Quarrying for natural construction material is very expensive and damages the landscape. This work therefore examines the use of gold mine tailings in the production of bricks.Different mixing ratios of gold tailings, cement, and water were used. The resulting bricks were then cured in three different environments - sun dried, oven dried at 360°C, and cured in water for 24 hours. The bricks were then tested for unconfined compressive strength, water absorption, and weight loss. The results showed that the mixture with more cement than tailings had a compressive strength of approximately 530 kN/m2. It was also found that the best brick curing system was in a water environment. Bricks made from tailings cost more than conventional bricks because of the higher quantity of cement used, but the manufacturing process consumes less water. Overall, the results indicated that gold mine tailings have a high potential to substitute for the natural materials currently used in brickmaking.Paper written on project work carried out in partial fulfilment of BSc. Eng. (Metallurgyand Materials Sciences)"

Jan 1, 2015

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By R. D. Hancock

The loading and selective properties of a number of commercial and experimental resins developed for the extraction of base metals were evaluated. Particular applications that ",:ere considered included the extraction of copper from artificial dump liquors, the treatment of Iow-grade copper, nickel, and cobalt liquors, and the removal of nickel from a cobalt electrolyte. Reagents that showed promise were two experimental resins developed at Mintek containing pyridyl imidazole active groups and two Dow resins, XF4195 and XF4196.

Jan 1, 1982

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By J. von Schéele

OXYFINESTM is an oxyfuel-based concept for in-plant recycling. It enables the possibility of fines, dust, sludge (without any drying step) and other by-products generated by the steel- and metal-producing industries to be recycled directly back into existing processes or a separate on-site unit. The results from a full-scale installation (20 000 t/a) and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. The latter include materials arising from ferrosilicon, ferrochrome and silicon manganese production. The concept not only provides a solution to the problems associated with dust and sludge generated in metal production, it also turns these materials into a low-cost raw material which is useful for the same production process, thus replacing some of the raw material input. If required, it could also be used, possibly as an intermediate solution, to convert the dust or sludge into an inert material with a suitable shape. Under some conditions, a directly saleable product could also be obtained. The paper reviews this technology, its status and benefits as wells as its possibilities with regard to application in ferroalloy production. Keywords: recycling, fines, dust, sludge, ferroalloys

Jan 1, 2004

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By J. N. van de Merwe

CONTRIBUTION BYH. WAGNER AND T.T. OZAN The paper by Dr J.N. van der Merwe makes an important contribution to the design of bord-and-pillar workings in the Vaal basin. It has been recognised for some time that the strength of coal seams in the Vaal basin is markedly lower than that of coal seams in other coal-mining districts in South Africa. However, there was insufficient data to quantify how much weaker the extensively jointed coal the Vaal basin is. A number of recent pillar collapses that occurred at Sigma colliery, the only remaining underground colliery in the Vaal basin, provided Dr Van der Merwe with an opportunity to make this assessment.

Jan 1, 1993

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l'assistance de l'industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d'un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By Steven M. Rupprecht

"The artisanal mining sector in Central Africa is largely informal, yet provides an essential livelihood for many (directly or indirectly) participants, as well as facilitating an important source for the flow of income into many communities. Artisanal mining varies from site to site, but appear largely well structured despite its informality. The artisanal mining sites in Central Africa have some inherent management structure and the extraction itself is often organised. Artisanal mining is labour intensive and is generally conducted utilising hand digging methods e.g. shovels or hand chisels. Artisanal mining is generally more dangerous than small-scale or large-scale modern mining operations. This is especially true as artisanal operations are generally subsistence activities with artisanal miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. The objective, through proper/dedicated training of artisanal miners is to migrate Artisanal mining to establish a small-scale mining (SSM) industry in Central Africa. Through developing the necessary skills in the fundamental areas of mining it is proposed that Artisanal Mining can become more productive and safer mining operations. The paper reviews the above focus areas, highlighting the skills and tools that are necessary to assist in establishing a sustainable small scale mining industry migrating from manual labour to semi-mechanised mining and processing. The purpose of the transformation process is to create a safe, healthy, environmental and community oriented mining operation with the objective to uplift the skills and wealth of the mineworkers and the general community."

Jan 1, 2015

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the theory of sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of along chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals, and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even lognormal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2010

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By E. Robles

The Tati Activox® Project (TA®P) is the first step towards the implementation of the Norilsk Nickel Activox® process. The ultrafine grinding (UFG) and autoclave pressure leach process conditions are the heart of the Activox® patent. Low grade base metal sulphide concentrates are leached in the process to recover the base metals and to produce LME grade nickel and copper cathodes and cobalt carbonates. The downstream processing of the metal-containing liquor produced by this process includes solvent extraction circuits to extract and concentrate metal-rich solutions, before the various final products are obtained. This paper gives an overview of many of the relevant design aspects taken into consideration in the design of the Tati Activox® solvent extraction circuits. It addresses key design elements related to leach process conditions such as scaling, materials selection for corrosive solutions, pH control, crud formation and treatment, multiple SX trains designed to prevent organic cross-contamination, and design aspects related to the mitigation of fire risks.

Jan 1, 2009

By M. A. Amarante

Beneficiation studies were conducted on a Portuguese feldspar ore, in order to obtain final products capable of being used in the ceramic industry. A simple scrubbing operation is enough to break the lumps in the feed. The ore deposit contains ca 35 x 106tonnesfrom which, by screening, three main products could be obtained. This paper focuses on the beneficiation of the 500/74 µm fraction, which constitutes about 27% of the ore, assaying 9.42% Al2O3,equivalent to approximately ca 46% feldspar, with a mean iron content of 0.29% iron oxides. Magnetic separation and froth flotation testwork was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron content of the feed to values between 0.04 and 0.08% iron oxides with an average yield greater than 90%. Flotation with HF, provided a feldspar recovery of 45?46% with a concentrate assaying 17.6% Al2O3. The use of H2SO4, gave a recovery of 35?36% of feldspar concentrate, assaying 16.1% Al2O3. However, economic and environmental advantages of using sulphuric acid may compensate for the lower mass recovery. The iron content of0.12% iron oxides in these concentrates, could be reduced to 0.04?0.05%, by further magnetic separation.

Jan 1, 1997

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007