Search Documents

By W. A. Te Riele

The National Institute for Metallurgy was the venue for a one-day colloquium on 'The Chemistry of Processes for the Recovery of Gold on Activated Carbon'. Organized by the South African Chemical Institute (Southern Transvaal Section) in collaboration with the National Institute for Metallurgy (NIM) and the South African Institute of Mining and Metallurgy, the colloquium attracted tremendous interest from the mining industry. Some 300 metallurgists, engineers, and chemists were brought up to date on advances in this technology made by scientists of NIM and the Anglo American Research Laboratories (AARL).

Jan 1, 1980

By M. Sciarone, B. Collins

The production, properties, and selection of ferrosilicon powders for heavy-medium separation by B. COLLlNS. B.Sc Eng. (Rand) (Fellow). T. J. NAPIER-MUNN. B.Sc. (Eng.). A.R.S.M. (Visitor). And M. SCIARONE. M.Se. Eng. (Delft) (Visitor). There are basically two types of ferrosilicon powder available to operators of heavy-medium plants in South Africa spherical and milled grades. The production processes are described, and the properties of the two types are examined and compared. Guidelines are given for the selection of the correct grade of ferrosilicon for any particular application.

Jan 12, 1974

By M. C. Harris

Float-sink analysis has wide application in the coal laboratory. This paper evaluates the established methods used for the float-sink analysis of fine coal, and then describes a new method and apparatus that can be used for material down to a few micrometres in size. The method is rapid and accurate, and requires only a small amount of sample. The results presented show close agreement with the float-sink analyses obtained by the more classical technique using separating columns. The new centrifugal method reduces the time required for the analysis by a factor of ten.

Jan 1, 1986

By E. Wroth, D. G. Krige

Written contribution E. Wroth* (Visitor): The technical aspects of the assistance scheme which IS provided for in the Gold Mines Assistance Act, 1968, and certain consequential amendments to the Income Tax Act, 1962, are explained by Dr Krige. The object of this contribution is to explain the working of the Gold Mines Assistance Act (hereafter referred to as the 'Assistance Act') for the benefit of those concerned with the tax and assistance assessments of gold mining companies. The views expressed do not necessarily reflect the Revenue Department's interpretation of the legal provisions involved. 1. MINES WHICH QUALIFY FOR ASSISTANCE 1.1 The assistance scheme is applied on a selective basis. Mines which qualify for assistance are defined in the Assistance Act as 'assisted gold mines'. The requirements for classification as an assisted gold mine are that: (i) the mine be a producing gold mine; (ii) it would be likely to close down within eight years if not assisted; and (iii) with State assistance its life would be appreciably prolonged and there would be a significant increase in production of gold or uranium, or of both gold and uranium. 1.2 A mine is only considered for classification as an assisted gold mine on application. Such applications must be made to the Mining Leases Board through the Government Mining Engineer. Classification of a mine as an assisted gold mine is at the discretion of the Minister of Mines who acts in consultation with the Minister of Finance and has regard to the recommendations of the Mining Leases Board. 1.3 The Minister of Mines will impose conditions subject to which a mine is to be classified as an assisted gold mine. The most important will be that the mine must immediately lower its operating pay limit, as normally calculated, by a percentage fixed by the Mining Leases Board and conduct its future mining operations in accordance with the average grade of its ore reserves determined on the basis of such lower pay limit. l.4 The Minister will fix the date as from which classification as an assisted gold mine is to be effective. So long as the mine has operated on the basis of the lowered pay limit for at least three months during the particular year of assessment, he would normally fix the effective date as the first day of the year of assessment.

Jan 5, 1968

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

By F. L. D. Cloete

he above article by E. Barnea, which appeared in the January 1978 issue of the Journal (vol. 78, no. 6, pp. 143-145), calls for comment in view of the author's claims for the novelty of his proof. He states in his article that its main purpose is to give a mathematically acceptable proof by induction of the 'recently proposed' equation

Jan 1, 1978

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

A number of issues relating to the computational aspects of pillar design are addressed in this paper. The computation of average pillar stress values is important when attempting to establish criteria for pillar design and in the analysis of the stability of tabular pillar layouts. One of the default ?classic? numerical methods that are used to determine pillar stresses is the displacement discontinuity method. In many instances it is not clearly understood that this approach does suffer from some limitations, particularly in relation to the fact that in coarse element simulations, the simulated average pillar stress (APS) can depend on the chosen mesh size. The nature of this error is highlighted in this paper and some strategies are suggested to bound the magnitude of these errors. It is demonstrated as well that the popular linear stiffness approximation to pillar or seam compressibility does appear to allow reasonably accurate estimates of the average pillar stress when either the pillar height is varied or when the seam modulus differs from the host rock modulus. A practical implication of this study is that if the seam modulus is noticeably lower than that of the host rock, such as for coal seams, it is important to use a linear stiffness constitutive model for the pillars rather than a ?rigid? pillar assumption. This added complexity seems unnecessary, however, when simulating hard rock pillars in mines where the seam modulus is very similar to that of the surrounding rock.

Jan 1, 2011

By M. David

This paper addresses the problem of technological transfer in geostatistics. Expert systems have become popular in certain fields because the needs of the industry are not provided for by traditional concepts and systems of education. The explicit knowledge approach in developing expert systems is presented through two experiments. The first describes a dedicated system written in GOLDEN LISP and the second a shell, using INSIGHT2, which has more general applications. Using expert systems forces on the user a new approach to parameter definition, and as an example an original method for the research of any anisotropy axes is developed which might well be useful in traditional programming. Two examples of application to a coal and a gold deposit are given.

Jan 1, 1987

By T. Uysal

The increasing demand for rare earth elements (REE) in highly strategic sectors such as hybrid electric vehicles, renewable energy, communication technologies, and the defense industry has made REE production methods important. In recent years, studies on REE have increased rapidly; however there are many studies on REE, there are not enough studies in the literature on the economics of the beneficiation process. RE ores are generally leached after beneficiation by gravity, magnetic and flotation methods. In this study, direct leaching, attrition scrubbing and leaching, and flotation and leaching methods are evaluated economically based on the data for the Mountain Pass (MP) facility. According to the sensitivity analysis performed as a function of capital cost (CAPEX), operating cost (OPEX), and rare earths oxides (REO) recovery, REO recovery has the biggest effect on the process economies. Although the flotation method entails additional investment and operating costs, transportation and operating costs are significantly reduced result of the higher grade and recovery. The flotation method is more profitable, with larger NPV and IRR values and a shorter payback period.

Jul 2, 2022

By L. Prosch

"The word 'sustainability' has gotten such a work out lately that the whole concept is in danger of floating away on a sea of inoffensiveness" Michael Pollon. It is estimated that approximately 65% of the roughly 130 million carats of diamonds mined globally per annum originate in Africa and has an annual value of US$ 8.4 billion', Many of these mines are located in remote areas of the continent where the directly affected project community's income is often well below the poverty line. Often associated with these communities are occurrences of localized over exploitation of natural resources, environmental destruction and the abundance of social ills.

Jan 1, 2010

By B. P. Watson

Uniaxial tests performed on core from instrumented sites at Amandelbult 1 shaft, Impala 10 shaft and Union Section Spud shaft showed a nonlinear elastic relationship between applied load and induced deformation. This nonlinear behaviour does not appear to be dependent on borehole orientation but in the case of the Amandelbult and Union sites appears to have been influenced by the stress condition of the rock mass at the time of drilling. Cores drilled at these two sites under destressed conditions, such as over a stope, showed a linear elastic response to the applied load whereas most of the cores drilled under relatively high radial stresses were nonlinear. The Impala 10 shaft tests, however, all showed strong nonlinear behaviour irrespective of the stress condition of the rock mass at the time of drilling, although high stress conditions may have influenced the severity of the nonlinearity. A comparison between underground stress change measurements and an elastic model indicated that the rock mass became nonlinear when the virgin stress condition was relaxed to about 10 MPa. The cores for laboratory testing were retrieved from vertical boreholes drilled up from the centre of a stope and from horizontal boreholes drilled over pillars and stopes at about 600 m, 1 100 m and 1 400 m below surface for the three sites respectively. The k-ratios under virgin conditions were estimated from sockets, modelling and stress measurements to be 1.0, 1.3, and 0.5 for the Amandelbult, Impala and Union sites respectively. Of the three sites, therefore, Impala 10 shaft appears to have had the highest virgin stress state. Tests performed on similar rocks from shallower depths at Impala Platinum essentially showed a linear relationship between stress and strain. From the small Impala Platinum rock test database available to the project, it appears that the nonlinear elastic behaviour initiates at this mine from about 1 000 m below surface and seems to become progressively more nonlinear below this depth. In addition, the nonlinear elastic rocks are weaker, have a lower Young?s modulus and a higher Poisson?s ratio than their linear elastic equivalents. Interestingly the tangential Poisson?s ratios of the nonlinear elastic materials are often greater than 0.5 at 50% of the failure stress, suggesting an early failure initiation. The paper describes the microscope and modelling work done to determine the causes of the nonlinear behaviour and discusses some implications of the behaviour for deep-level mining.

Jan 1, 2009

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By K. Schwerdtfeger

Data are presented on the effect of iron oxide on the electrical conductivity of CaO-SiO2-FeO-Fe2O3melts, and on limiting current and impedance in direct current or alternating current charge transfer at iron electrodes. The strong influence of iron oxide content can be utilized for in situ determination of total iron oxide content and Fe3+/Fe2+ratio. The possible probe designs are presented and the principles and procedures of the measurements are explained. Keywords: in situ probe for iron oxide determination in steelmaking slags, electrical conductivity of CaO-SiO2-FeO-Fe2O3slags, direct current over voltage and alternating current impedance at iron/slag electrodes.

Jan 1, 2004

By R Linares

For centuries, diamond's superlative properties have earned it a reputation as the 'dream' material for mankind in its search to create advanced applications. Until recently, this dream has been realized only in the use of diamond for gemstones and abrasive applications where several tons of diamonds are now used on an annual basis. The vision of having large, high quality diamond as part of a broad engineering tool-kit for many diverse high tech industries is now becoming a reality however, with the advent of early stage commercial availability of single crystal and poly crystalline CVD diamond.

Jan 1, 2010