Search Documents

Novel flotation reagents were developed to improve the flotation of coarse particles. Laboratory tests conducted on an anthracite coal sample from Kyung-Dong Coal Company, Korea, showed that the reagents can successfully clean 2?3 mm top-size materials. Pilot-scale tests conducted on a 1.41 mm x0 coal gave substantially better results than those obtained using kerosene as collector. The pilot-scale test results were used to develop a flowsheet, in which the 1.41 mm x0 fraction is cleaned by flotation and the 4 x1.41 mm coal is cleaned by single-stage spirals. The performance of this circuit was compared with another flowsheet, in which the 0.5 mm x0coal is floated using the conventional flotation reagent, with the 4 x0.5 mm material being cleaned using two separate spiral circuits. The performance of the two flowsheets was compared by computer simulation. The results showed that the flowsheet consisting of the coarse particle flotation circuit can give substantially higher yield sat a given product grade. Keywords: coal flotation, coarse particle flotation, collector, spirals, computer simulation.

Jan 1, 2002

By M. G. Maruma, L. A. Mampuru

"Mill liner wear is a major cost item in the mining industry and there is continuous research to prolong the life of the liners. Over the years it has become apparent that even though high-chromium white cast irons are highly efficient as abrasion-resistant materials, a combination of wear resistance and fracture strength remains difficult to achieve. Increasing the hardness of the high-chrome white cast iron (HCWCI), which improves the resistance to abrasion wear, is often accompanied by a deterioration in fracture strength. Operational conditions inside the mill require that the liner should be made of highly wear-resistant material with some fracture strength. Vanadium additions ranging from 0.2 to 3 wt% were made to HCWCI in an attempt to refine the microstructure. It was found that an increase in vanadium content promotes grain refinement. A content of 1.5-3 wt% gave the best results as measured by the maximum breaking strength.IntroductionOver the years it has become apparent that even though high-chromium white cast irons are highly efficient abrasion-resistant material, a combination of excellent wear resistance and fracture strength remains difficult to achieve. The exceptional wear resistance of highchromium white cast iron (HCWCI) is attributed to hard chromium carbides embedded in an austenitic/martensitic/pearlitic matrix. When the chromium contents exceed 12 wt%, interconnected MC3-type carbides of conventional cast irons are replaced by rodshaped and isolated M7C3 carbides (Powell, 1980), leading to an improvement in the impact toughness, ductility and fatigue resistance. However, the main M7C3 carbides in HCWCI are hard and brittle and can provide an easy path for crack propagation. This limits the applications of HCWCI, particularly in severe impact conditions. Most operations involving HCWCI are in crushing and grinding and the life of a part/liner is limited by its wear resistance. However, improving the wear resistance of HWCI comes at the cost of a significant reduction in fracture strength. Concerns about premature failure of HCWCI mill liners in the mining industries prompted a study to improve the wear resistance and mechanical properties of HCWCI."

Jan 1, 2016

By G. Dellas, R. Mangera, A. Voigt

"X-ray transmission (XRT) sorting has become the preferred recovery technology option in several parts of the diamond-winning flow sheet. In the De Beers Group, applications of XRT are found across kimberlite, alluvial, and marine operations. This is the result of intensive R&D conducted over the years to arrive at a suite of machine embodiments capable of sorting and auditing diamonds across all size ranges.The first applications in the marine environment used the technology in an auditing mode, and served as a useful early predictor of diamond content weeks ahead of sorthouse returns. The same machines are now available with ejection capability to produce high final product grades. The next application was tests on coarse alluvial gravels as an alternative to dense medium separation. The results were very encouraging, and tests are planned for both green- and brownfield kimberlite environments, as well as to explore an alternative to conventional techniques in final diamond recovery. At the Jwaneng mine Large Diamond Pilot Plant (LDPP), the objective is to recover diamonds in the size fraction –45 +25 mm.The technical challenge remains in the finer sizes, for high-capacitymachines as direct alternatives to conventional diamond recovery technologies. This is an area of ongoing R&D and it is only a matter of time before the breakthrough emerges. X-ray transmission fundementalsXRT makes use of X-ray imaging techniques to analyse objects and materials, and has a wide range of applications from baggage scanning for security purposes (Martz et al., 2016), to recycling of waste material (Owada, 2014). During the last decade XRT has been applied to an increasing extent in the minerals processing industry (von Ketelhodt and Bergmann, 2010; Sasman, Deetlefs, and van der Westhuyzen, 2018). Dual-energy XRT (DE-XRT), in which images of the target material are obtained at both high and low Xray energies, allows for elemental analysis and therefore can be used to discriminate between various minerals.A DE-XRT system makes use of a dualenergy X-ray line scan sensor to generate images of transmitted X-rays (Figure 1). Dualenergy refers to the camera, which contains two sensors, one responding to low-energy Xrays and one to high-energy X-rays. Feed material can be imaged either while on the belt, or while in flight."

Feb 1, 2019

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By G. M. Brown, B. J. Ebacher, W. G. Koellner

Introduction There is a continual economic push to increase the productivity of mobile material handling equipment used in open pit mines. This includes the largest electrical machines: excavators (draglines and shovels) and haul trucks (Figure 1). Existing DC drive systems used on this type of equipment are a mature technology. They have no further economic potential to accommodate larger equipment be-cause of the high maintenance costs and the trade-off between power, speed and space limitations of their DC traction mo-tors. In recent years the large-scale introduction of AC drives in the rail transportation sector1,and the availability of poworful GTO and IGBT modules have led to the devolopment of compact, powerful, an drugged AC inverter drives specifically adapted to the mining market2,3. The major advantage of AC drives stems from the squirrel cage induction motor which eliminates the DC commutator. This leads directly to higher speed, increased power density, higher reliability, greater efficiency and lower maintenance of the traction motors. In the context of excavators and haul trucks, additional benofits driving the move to AC are (i) increased production rate due to higher machine speed, and power density, (ii) increased reliability and lower cost inverters using 3.3 kV IGBT's, (iii) active front-end (AFE) technology that improves compatibility with the mine power grid and an proved dynamic response,(iv) intelligent converter design that provides increased fault tolerance, (v) contextual maintenance software that facilitates trouble-shooting, and (vi) remote diagnostic capabilities. This paper describes how these and other features of AC drives lead to higher productivity in mining shovels, draglines, and haul trucks. Minimize the cost per ton of material moved The overall goal that drives design and sales of excavators and haul trucks is the constant requirement to reduce the cost per ton of material moved. Whether this involves blasting, loading trucks, or hauling material to the crusher or waste dump, equipment that reduces the cost per ton of material moved contributes to a more profitable operation. An accurate determination of the true cost per ton to move material must consider every aspect of the equipment and the circumstances under which it is used. Procurement and capital costs, fuel, operating, and maintenance costs over the useful life, and eventually the cost of scrapping should all be taken into account to determine the real cost per ton of moving material. We will focus on two broad areas that relate to the equipment itself; factors influencing the amount of material moved (Table I) and factors influencing the cost of material moved (Table II). Emphasis will be given to those elements in the tables that most influence the productivity of excavators and haul trucks due to the application of AC drive technology. Maximize the amount of material moved Maximize production rate he production rate refers to the quantity of material that can be loaded or moved per hour. This generally involves larger, faster, and more powerful equipment that operates more reliably to minimize down-time. AC motors Figure 2 compares the hoist motor speed-torque response of two 77 t (85 short ton) shovels, one AC the other DC. The absence of commutation limits on the AC motors enables the AC shovel to operate with a greater area under the speed-torque curve, resulting in faster lowering speeds and reduced times for the swing to return to the pit. This is especially important for short swing angles where the operator may have to wait for the dipper to lower. Reducing the cycle time by 6 to 8 seconds at the shovel translates into an increase in shovel production of about 20%. Larger equipment The bucket capacity of excavators has increased approximately 100-fold over the last century. Figure 3

Sep 1, 2001

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

By R. S. McDonald

Auburn began operations 40 years ago with an office in Sudbury, Ontario, Canada, to provide services to Inco Limited. Over the next 40 years, operations expanded considerably, with projects being undertaken around the world, servicing the smelting and refining industry. Operating bases have been established in Canada, United States, Mexico, Chile, and Spain, with further growth expected to continue with an operating presence in South Africa. The Auburn Group of companies has serviced the smelting and refining industry for over 35 years. Auburn services a variety of metallurgical plants, and our worldwide experience has gathered considerable knowledge on industry processes and maintenance solutions. Today, the ?Business of Smelting? tackles demanding challenges, and operators search for opportunities and solutions to improve smelter maintenance, reduce operating costs, and decrease downtime. The Auburn Group has developed project teams, technologies, and equipment that provide specialised and innovative solutions to the non-ferrous metal industry to help address these challenges. Our Furnace Services team offers a variety of repair and maintenance services for metallurgical furnaces. Our specialised team has proven methods for completing projects quickly and safely. Our worldwide experience includes turnkey project management, construction, and various scopes of work for demolition and refractory repairs on all types of smelting and refining furnaces. Auburn developed the Results FirstTM programme to provide optimized solutions and results for smelter projects. The programme utilises a proven three-step model for improved results for schedule, budget, safety, and ramp-up to production. Our experienced Project Management teams can handle the planning and construction management of capital projects and plant shutdowns. Our projects have involved smelter/refinery modifications, oxygen plant installations, and sulphuric acid plant audits and maintenance. Our Equipment & Products division supplies specialised equipment and products, which are used in the metals industry for plant maintenance tasks. Our capability to design unique equipment, combined with our ability to source products worldwide, makes us a useful resource to find the best-suited equipment to meet the work-site demands. We specialise in custom remote-control units to handle specific maintenance solutions for smelters and refineries, and custom equipment designs for catalyst handling for Acid Plant maintenance. Our extensive knowledge of and experience with industrial technologies allows us to provide a wide range of Industrial Services. These services include vacuuming, high-pressure water blasting, chemical cleaning, pelletizing, dredging, ore bin clearing, roaster repairs, baghouse/ESP services, and manpower supply for both industrial plants and mines. Auburn?s combined strength of personnel experience, knowledge of industry processes, innovative project methods, and equipment technology make Auburn a unique resource for problem solving on every facet of smelter operations.

Jan 1, 2006

By D. Grobbelaar, A. Cichowicz, D. J. Birch

The Q-coda method for estimating the quality factor Q(f)= Qo(f)n was used to characterize seismic wave attenuation in a region of the Kaapvaal Craton that includes the mining areas of the Bushveld Complex and Witwatersrand Basin. Seismic waveform data, collected by locally distant stations of the South African National Seismograph Network (SANSN), consisted of mining-related events with magnitudes ranging from ML 1.8 to ML 4. Q was calculated for nine different source-receiver pairs spanning the study region. A weighted average Q based on the number of available data gave an estimated attenuation relation for the study region of Q(f) = 327 f 0.81.

Jan 1, 2015

By I. Mitov, A. Stoilova, D. Krastev, B. Yordanov

We present three technological scenarios for the recovery of valuable components from gangue, stored in the tailings dam at Kremikovtzi metallurgical plant in Bulgaria, into marketable iron-containing pellets. In the first approach the iron concentrate was recovered through a two-stage flotation process, desliming, and magnetic separation. In the second proposed process, the iron concentrate was subjected to four sequential stages of magnetic separation coupled with selective magnetic flocculation. The third route entails the not very common practice of magnetizing roasting, followed by selective magnetic flocculation, desliming, and magnetic separation. The iron concentrate was pelletized in a laboratoryscale pelletizer. Each technology has been assessed with regard to the mass yield of iron concentrate, the iron recovery. and the iron, lead, and zinc content in order to identify the most effective route.

May 1, 2021

By Willem Le Roux

The common law requires an employer to take reasonable steps for the safety of employees. In general, the duty of care means that the employer, acting personally or through its employees or agents, must take reasonable care for the safety of its employees (Van Deventer v Workmen?s Compensation Commissioner; 1962 (4) SA 28 T; Oosthuizen v Homegas (Pty) Ltd 1992 (3) SA 463 T).The duty of care includes the provision of safe premises, safe machinery and tools and a safe system of work. The obligation is not an absolute one, but is restricted by the concept of reasonableness. The common law duty may, in certain cases, include the assessment of hazards and risks. 2 International law Great emphasis has been placed in the Western world on the prevention of occupational diseases and injuries. Detailed statutes and regulations govern specific industries in many countries. See, e.g. the Control of Substances Hazardous to Health Regulations of the United Kingdom and various regulations applicable to the use of asbestos and lead, fire protection, mines and quarries, petroleum, etc. Risk management is an important part of managing health and safety. In the United Kingdom, the Management of Health and Safety at Work Regulations, 1999, require every employer to make a ?suitable and sufficient assessment of the risks to health and safety of his employees to which they are exposed whilst they are at work?. The particularity of the assessment is determined by the risk in question.

Jan 1, 2011

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

By P. van Dorssen

In South African metalliferous mines, stoping operations are largely confined to narrow, tabular orebodies making mechanization extremely difficult. Limited flexibility in terms of stope width has necessitated drilling by means of handheld, pneumatic rock drills at most of our operations. As the largest producer of platinum in the world, we drill in excess of forty million stope blast holes per annum. Cleaning of the broken ore is also done by conventional means?utilizing scrapers and scraper winches. Conventional methods such as these carry high costs in terms of risk exposure as well as labour intensity. The purpose of this paper is to describe the development of a long hole stoping system suitable for the narrow platinum reefs. The new system had to be substantially safer and more cost effective than conventional mining. We selected a site that was conducive to mechanized mining and set out the parameters that we considered would meet our requirements. We then conducted a feasibility study to evaluate the conceptualized long hole stoping system in terms of specific goals. An analysis of the proposed system identified the Key Performance Indicators (KPIs). One of the most critical goals was to be able to create a man-free stope. This would mitigate the safety risk associated with normal stoping operations, as well as the inefficiency cost previously referred to.

Jan 1, 2002

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By L. Wade

Laboratory testing of the self-heating propensity of coal, using crossing-point temperature and differential thermal analysis techniques, involves the frequent recording of several temperatures. The volume of data and the desire for high accuracy of measurements motivates an automated recording system. The data which are recorded must be adjusted for calibration factors and the results presented in both graphical and tabular form. The paper describes hardware and software features of a computerised system which is being used to establish the relative propensity to self-heating of a wide variety of coals.

Jan 1, 1987

By J. Githiria, C. Musingwini, J. Muriuki

"The maximization of net present value (NPV) is a primary objective in open pit mine planning processes. In an attempt to meet this objective, cut-off grades are considered in all the stages of mining. There are three stages involved in resource extraction, namely mining, processing, and refining/marketing, which are all defined in Lane’s approach. Using Lane’s approach, the economics involved in each stage are identified independently and interact to provide an optimum cut-off grade.A hypothetical block model is used to illustrate how a computer application (Cut-off Grade Optimiser) that was developed in this study is used in the optimization of cut-off grades using Lane’s algorithm. This paper analyses the application of Lane’s approach for a single element in cut-off grade optimization as applied in the calculation of the optimum cut-off grade through a computer-aided application.Although Lane’s approach is not complex it is not widely applied to maximize the NPV of mining operations as the iterative calculations can be lengthy. The computer application developed in this study shows how Lane’s algorithm combined with a linear programming function can optimize cut-off grade with regard to the complex situations faced by mining operations. The application saves users from performing otherwise lengthy, iterative calculations.Background and previous researchAn open pit mining complex constitutes multiple pits, ore processing streams, and metal refining options. An open pit mine produces ore (valuable) and waste material. Ore is transported to an appropriate processing stream for producing concentrate. A refinery processes the concentrate to produce marketable metal product (Lane, 1964, 1988).Cut-off grade optimization is based on Lane’s theory, where a mining system consists of three major stages such as mining, milling, and refining. In this approach the cut-off grade selection is done between six cut-off grades that involve all stages of a mining operation. Selection of the optimum cut-off grade influences the net present value (NPV) by maximizing the net cash flows from the operation."

Jan 1, 2016

By E. A. van Wyk, M. R. de Villiers

"Mining companies strive to increase and maintain production, while simultaneously remaining competitive in the global economy. Furthermore, they must ensure workers’ safety and maintain good safety records. The use of virtual reality (VR) facilitates the development of tools and systems for various purposes that can improve knowledge and understanding of the work environment. VR is a rapidly growing technology that uses the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and standard 3D graphics card, make VR technology viable and attractive for mainstream training applications. The design, development, and implementation of interactive VR training systems is proposed as an innovative approach to augment safety training. However, in order to assess the impact of such VR training systems it is of particular importance to determine the effectiveness of the design of such systems. This article proposes an evaluation framework for this vital purpose. This framework comprises criteria to assess VR training systems, specifically relating to usability, instructional design, VR systems design, and mining industry context-specific aspects. Although the framework was developed as an evaluation tool to assess effectiveness of the design of such systems, it can equally well be used as a set of design principles to inform the design of VR training systems for mining. IntroductionMining in South Africa has been the main driving force behind the history and development of Africa’s richest and most advanced economy (Coka, 2012). The South African mining industry is frequently criticised for its poor safety record and high fatality rate (Stoddard and Skweyiya, 2016). Inadequate or insufficient training is often cited as a root cause of accidents (Van Wyk and De Villiers, 2009; Tichon and Burgess-Limerick, 2011). Virtual reality (VR) is a rapidly growing technology that utilizes the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction (Webber-Youngman and Van Wyk, 2013). VR is currently being used or investigated as a training solution in a variety of industries. VR technology has developed rapidly and costs have fallen to levels where it can now be considered for mainstream training applications. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and a standard 3D graphics card, make VR even more attractive to mine training centres (Van Wyk and De Villiers, 2009)."

May 1, 2019

By H. von Blottnitz, B. E. Isheloke

Mining is a significant economic activity in most Southern African Development Community (SADC) countries, and mineral beneficiation has been identified, and controversially discussed as one of the possibilities for industrialisation. With many member countries being economically too small to muster the human and financial resources which beneficiation requires, the recently adopted Regional Mining Vision (RMV) envisages interventions at a regional level. An opportunity arose to ask industry role players to what extent the SADC appears to support regional beneficiation policy interventions undertaken by member countries, and what the challenges are in undertaking beneficiation regionally, as a complement to, or substitute for country-specific beneficiation policies. Twenty-five semistructured interviews were conducted with experts from SADC member countries during the 2019 Mining Indaba. Participants were divided on whether beneficiation should be carried out nationally or in the SADC region. While beneficiation could support value-keeping, key challenges were found to be infrastructure development (i.e. energy, water), scarce skills, access to technology and related costs, but also lack of free trade and movement. We submit that a more integrated beneficiation strategy for the SADC region, as is being developed through the RMV, would indeed be relevant in the future. Keywords: Mineral beneficiation, regional integration, beneficiation policy interventions, African mining vision, mining, SADC

Jan 1, 2020

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988