Search Documents

By A. Hammel

This paper summarizes indigenous mining methods used to collectmetal ores in pre-colonial southern Africa, south of 15°S. These methods, for the purposes of discussion, are divided into sections inorder of increasing organizational complexity, from scavenging,which only required basic equipment and a relatively minimal division of labour, to underground mines, which necessitated complex planning to overcome obstacles such as the need for illumination and ventilation. Examples concerning the pre-colonial exploitation of iron, copper, tin, and gold have been taken from the archaeological literature. This review paper provides an introduction to the technology that was available to and used by miners in the past, illuminates some of the factors limiting their operations, and supports the claim to the indigenous nature of this activity

Jan 1, 2000

By G. E. Blight

The load-compression characteristics of mine supports are usually evaluated by means of relatively rapid tests, whereas in the mine they are subjected to much slower strain-controlled compression. The effects of slow strain rates on the load-bearing properties of mine supports were explored by means of straincontrolled tests on model timber packs and timber-filled steel telescopic props. It is shown that the load-compression characteristics of these supports are considerably influenced by the rate at which they are compressed. The species of timber influences the behaviour, but to a relatively minor extent. Preloaded supports are shown to lose a significant proportion of their preload by relaxation.

Jan 1, 1978

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016

1. Book review . Australasian coal mining practice, edited by C.H. Martin. Reviewer: R.B. MacGilIivray This book is an extremely comprehensive coverage of coal-mining practice in Australasia, the countries covered being Australia, New Zealand,and Papua New Guinea. 2. From The Institute of Metals The folowing are available from The Institute of Metals, 1 Carlton House Terace, London SWl Y 5DB. Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00. High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15. New cored-wire injection techniques, particularly as Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45. Marine engineering with copper-nickel. 1988. 103 pp. £18. Characterisation of High Temperature Materials. 3. New journal FMJ International Publications Lid have announced a new quarterly publication, Aluminium Today. 4. Other new publications Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95. Proceedings, Foundry and Heat Treatment 88. R150 per set of 5 volumes, or R40 per volume.

Jan 1, 1989

1. Book review Steels- microstructure and properties, by R. W. K. Honeycombe. London, Edward Arnold, 1981. 244 pp. Rl9,90. (Reviewer: P. T. Wedepohl) 2. New books Decision making in continuous steel casting, by Mark A. Vonderembse. New York, Bowker Publishing Co., 1981. U8 pp. Handbook on continuous casting, by E. Herrmann' Diisseldorf, Aluminium-Verlag GmbH, 1980. 742 pp. Cloth DM 1250, leather DM 1500. Pore structure analysis from a nitrogen adsorption study of porous materials using a volumetric method. User's guide to the FORTRAN programs: PORESl and PORES2, by E. G. K. Woods. Pretoria, CERGCSIR (P.O. Box 395, Pretoria 0001), May 1981. Oil and gas from coal, by Dick Olliver. London, Financial Times (10 Cannon Street, London EC4P 4BY), 1980. £120. The seventies: a review, the eighties, a preview, by W. Hibbard (editor). Oxford, Pergamon, 1981. 120 pp. £12.50. Computers in materials technology, by T. Ericsson editor). Oxford, Pergamon, 1981. 230 pp. £14.50.

Jan 1, 1981

By G. E. Blight

The mining industry is making increasing use of pumped tailings fills. The properties that affect the performance of tailings fills are described by means of typical examples. They are the particle-size grading for maximum density, the water content for pumpability, settlement after placing, compression and drainage under stress, shear strength, and resistance to shock loading.

Jan 1, 1979

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

By H. -U. Lim, C. -H. Kim

The sixth underground pumped powerhouse cavern is under construction now in Korea. For the stability analysis of the five underground powerhouses, finite element method was used. For this analysis, in-situ rock stresses were measured by overcoring method and horizontal to vertical stress ratio was calculated 1.07-1.32 at four sites. Rock mass strength and elasticity were assumed from intact rock properties. The ratio of elasticity of rock mass was 0.16-0.55 of intact rock core elasticity. In general, elasto-plasticity with Mohr-Coulomb failure criterion was applied and the input cohesion and internal friction angle were approximately 0.12-0.22, 0.6-0.87 of intact rock strength parameters, respectively. Der sechste Untergrund-gepumpt-Powerhouse-Cavern ist jetzt im Bau in Korea. Für die vergan-gene Stabilitätsanalyse des fünf unterirdischen Powerhouses in Gebrauch wurde ein begrenztess Elementsmethode benutzt. Für die Analyse wurden In-Situ Felsenspannungen von overcoring Methode gemessen und Horizontale zu senkrechtem Spannungsverhältnis waren als 1.07-1.32 an vier Stellen kalkuliert. Felsenmassenkraft und Elastizität wurden von unversehrtem Felsenei-gentümern angenommen. Das Verhältnis der Elastizität von Felsenmasse war 0.16-0.55 von un-versehrter Felsenkernelastizität. Im allgemeinen wurde Elasto-Plasticity mit Ausfallskriterium des Mohr-Coulombs verwendet. Die Eingabebindekraft und die innere Reibungswinkel waren unge-fähr 0.12-0.22, 0.6-0.87 von unversehrtem Felsenkraftsparametern, jeweilig. En Coree, la sixieme centrale souterraine de la pompe d'accumulation dans la caverne est en construction. La methode d'element fini a ete utilisee pour analyser la stabilite de cinq dernieres centrales en service. Dans cette analyse, la reaction de la roche sur place etait mesuree par la methode d'overcoring et celle du rapport horizontal-vertical etait calculee de 1.07-1.32 en quatre places. L'intensite et l'elasticite de la masse de roche ont ete estimees de la roche intacte. Quant a l'elastic-ite, sa masse de roche etait 0.16-0.55 fois que celle de la roche intacte. En general, elasto-plasticite avec le critere de defaut Mohr-Coulomb etait utilisee et sa cohesion d'energie et son angle de friction interieure etaient supposees respectivement 0.12-0.22, 0.6-0.87 fois que la parametre de l'intensite de roche intacte.

Jan 1, 2003

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By W. Spencer

An examination is made of quality standards in castings produced by the South African foundry industry, and some examples are given of the consequences of poor quality to the user. Corrective measures are suggested.

Jan 1, 1981

By A. Bothma

The Impala No. 1A ventilation shaft is located approximately 15 kms north of Rustenburg and is accessed via the R510road from Rustenburg to Northam/Thabazimbi. This situation is shown on the location plan in Figure 1. The geology at the site consists of an upper layer of black turf of about 1 metre in thickness, grading into weathered norite. The depth of weathering is generally less than 5 metres. Zones of deeper weathering may occur along fracture zones associated with faults and dykes. Groundwater occurs mainly within the weathered/fractured aquifer system. The ventilation shaft is a 5.1 m diameter upcast shaft ,and forms part of a system of ventilation shafts to complement the existing infrastructure as mining progresses down the new twin decline extension of Impala 1 shaft. The principal reason for these shafts is to lessen the risk of an extended RAW and also to counter the effects of the heat build-up as the mining goes deeper, with the resultant effect that the existing cooling centre (fridge plant) becomes more remote from activities. The No. 1A shaft (upcast) is positioned approximately 1,2 km on down dip from the main shaft and the No. 1Bshaft (downcast) approximately 1,2 km further. Geological information was used from a borehole 1,2 km away on strike from the upcast shaft. The first shaft (1A) is a 5,1 m diameter hole to be fitted with two 2,2 MW fans, whilst the second shaft (1B) is 4,1 m diameter to accommodate a 7MW fridge plant.

Jan 1, 2001

By A. McQuillan, N. Bar

Geotechnical engineers are routinely tasked with advising suitable stand-off distances below highrisk sections of slopes in open-pit mines that are identified to have potential to deform or collapse. Accurate prediction of failed material runout can mean the difference between continuous safe mining and unwanted high-potential incidents that result in loss of production, equipment damage, injury, or loss of life. This paper updates previous empirical relationships presented by the authors for estimating the volume and runout distance of excavated slope failures, in an open-pit mine operation, using slope geometry as the primary predictor. Cases are sourced from varying slope geometries (fall heights up to 385 m, slope angles up to 80°) and a range of commodities (iron ore, coal, nickel, gold, copper, boron, and limestone), excavated in sedimentary, banded-sedimentary, epithermal, and copper-porphyry deposits, across all six inhabited continents. Analysis of these cases identified positive correlations between slope height and runout distance, and slope height and failed material volume. In general, negative correlations were identified between Fahrböschung angle and slope height, and Fahrböschung angle and failed material volume; however, significant scatter is observed in these datasets. A definitive relationship could not be derived comparing Fahrböschung angle with failed material runout. Slope angle was also found to be a poor indicator of runout. Of the parameters analysed, slope height (i.e., fall height) was found to be the simplest and best predictor of runout distance. This paper presents new charts for predicting failed material runout distance for rock slopes. Relationships are defined for structurally and rock-mass driven slope failure mechanisms at average, 75%, and 95% prediction intervals

Jul 10, 2024

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

1. New books from The Institute of Metals Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00.High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45.Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Marine engineering with copper-nickel. 1988. 103 pp. £18.Sir Henry Bessemer: An autobiography. 1989.380 pp. £16.95. 2. Other publishers Occupational safety and accident prevention. Behavioural strategies and methods, by C.G. Hoyos and B.M. Zimolong. Amsterdam, Elsevier, 1988. 218 pp. Dfl. 180.00. Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95.

Jan 1, 1989

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By S. M. Brabyn

The wear in mild steel pipelines used to convey rod-milled waste backfill was determined and then compared with that obtained using a laboratory rig designed to simulate the wear condition in slurry pipelines. The relative importance of corrosion and abrasion was investigated under various conditions of water quality and particle size distribution. The laboratory rig was then used to evaluate other possible materials of construction for backfill pipelines. A preliminary assessment of the economic viability of pipelines made of alternative materials is included.

Jan 1, 1988

By R. Rampersadh

Paper written on project work carried out in partial fulfilment of B Eng (Metallurgical Engineering) degree Steel was sampled after calcium treatment, to follow changes in inclusion composition during the processing of alumium-killed steel into continuously-cast billets, at Mittal Vereeniging. There is some shift in the distribution of inclusion compositions towards alumina, as the liquid steel moves from the ladle to the tundish. This shift may reflect some reoxidation. However, the effect on inclusion modification is small, since only a small fraction of the tundish oxide inclusions is fully solid?which agrees with the plant observation that these heats cast without clogging. Magnesium oxide in the inclusions contributes to liquid formation, substantially increasing the range of lime: alumina ratios over which the inclusions are partially or fully liquid.

Jan 1, 2006

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

By V. I. Zhuchkov, L. A. Smirnov, E. I. Arzamastsev, A. A. Babenko

A brief analysis is given for state-of-the-art of manganese and chromium ferroalloy production in Russia and their consumption by metallurgy plants. The main causes of low output of manganese and chromium ferroalloys, and ways to resolve the issue of ferroalloy production development are considered.

Jan 1, 2004