Search Documents

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012

By L. Jurca, C. Gligor

After 1990, a great process of re-organisation and economic reform has occurred in the Romanian mining sector and especially in the pitcoal mining in the Jiu Valley. This process has included both legislation and the main aspects for getting an economic efficiency in the environment issues and for dealing the problems with social impact. Accordingly, starting with the year 1993 a new mining method has been introduced to turn efficient the pitcoal mining, and we speak about mining with caved in bed. This method has two variants: - with transverse strips and caved in bed; - with long face and caved in bed. Each of the above-mentioned variants has in turn several subdivisions, depending on how the longwall is prepared and on other characteristics. By using this method, the output has increased compared to other mining methods. The main safety aspects concerning caved in mining refer to: - great emissions of methane; - technical aspects (a mining method system, supports, discharging process); - pressure driving (analysed for the case of mining with long face, with transverse strips as well for the case of transverse strips when mining a subsequent sublevel).

Jan 1, 2003

The theory of geostatistics covers a branch of .applied statistics aimed at a mathematical description and analysis of geological observations. Geostatistics can be used in pure geology (for example, for the analysis of trace elements in a metamorphic rock), in mineral exploration (for example, for the analysis of geochemical exploration data), as well as in mine valuation. This book is intended to provide a practical introduction to the theory of geostatistical methods of mineral evaluation. Over the years, various mathematical models have been developed to represent the distribution of values in mineral deposits. The simpler models are based on the assumption that the values are randomly distributed. Classical statistical methods, based on this assumption of the random distribution of values, are used to analyse mineral deposits to which these models apply or are assumed to apply. In all mineral deposits, however, one recognizes the presence of areas where the values are higher or lower than elsewhere. Also, the values of two samples in a mineral deposit are more likely to be similar if the samples are taken close together than if they are taken far apart. This indicates that there exists a degree of correlation between sample values, and that this correlation is a function of the distance between the samples. Models have been developed which take this correlation into consideration, with the degree of correlation between sample values being usually measured by the semivariogram function. In these models the fact that two samples taken next to each other will most probably not have the same value, must also be considered; even for very short distances the correlations are usually not perfect and a purely random component is present in the value distribution. The mathematical models will therefore assume the presence of two sources of variability in the values: a correlated component and a random component. Finally, one must consider the particular and very common case of mineral deposits in which the values present a systematic variation in space. This variation is usually referred to as a drift, or a trend. For example, the grade of an ore body may increase with depth of the ore, or it may decrease when one moves away from a central volcanic pipe. The earlier models did not give a satisfactory representation of drifts, and more complex models have been developed, in which three sources of variation are represented. These models are made up of: a deterministic component, a correlated component, and a random component. The deterministic component is used as a model of the drift. The correlated component explains regular changes in values which are not represented by the drift. The random component represents variations which cannot be explained by any of the above factors. The simpler models, based on the assumption of a single random component, will be described first (Chapter 2). The models based on the hypothesis of the superimposition of a correlated component on a random component, will then be analysed in detail. These models are most commonly used in the analysis of mineral deposits (Chapters 3-1 I). Finally, how to deal with the presence of a drift will be briefly described (Chapter 12). This book has been written essentially for students in mining engineering and for mining engineers who are interested in the background to the theory of geostatistics as well as its practical applications. The assumption is made that the reader has an elementary knowledge of statistics. Some knowledge of linear algebra is useful in part of Chapter 9, and is necessary to read Chapter 12. A proof is given of all the equations related to geostatistics, and which are not usually found in elementary textbooks on statistics. Understanding of these proofs is not necessary for practical application of the theory, and the reader may wish to skip them on a first reading, concentrating attention on the numerous simple practical examples given. Although the theoretical geostatistician will not find much new material in this publication, it is anticipated that he will develop some interest in the practical approach chosen to prove the various geostatistical equations. Many people and institutions contributed to the preparation and completion of this work. I am much indebted to Dr D. G. Krige and the Anglo Transvaal Consolidated In- vestment Company Limited, who gave me the opportunity to spend a considerable amount of time working on geostatistical problems, both theoretical and practical, during the time that I was in their employment. Dr Krige contributed greatly in developing my interest in studying both the theory and practice of geostatistics, always insisting that a correct balance be kept between theory and practice. I am grateful to Professor H. M. Wells and the Mining Department of the University of the Witwatersrand for inviting me to give lectures in a post- graduate course on geostatistics. The notes 1 prepared for that course became the foundation of the present work. I am also indebted to the Centre de Geostatistique of the École des Mines de Paris, where I received my first formal education in geostatistics during a summer course given by Charles Huijbregts, after many years of my lonely plodding through the published literature. Many graphs in the present volume are reproduced with the permission of the Centre de Geostatistique. The Department of Metallurgical and Mineral Engineering of the University of Wisconsin-Madison has also contributed in making this work possible, by allowing me to spend a considerable amount of time and resources in the writing, typing, and correcting of successive drafts. I am thankful to Lynn D. Kendall, who typed the entire manuscript under constant pressure.

Jan 1, 1978

By Penswick D.

From the perspective of management control, most mining operations can be represented by a hierarchy comprising four layers. The base of this hierarchy consists of the individual pieces of equipment that are used to break and transport rock. The next level comprises the coordinated interaction between different pieces of equipment, termed a process. An operation results from the bringing together of different processes within a common discipline, such as mining or hydrometallurgy. Finally, an enterprise is formed when the separate mining, concentrating and smelting business units are combined. To date, much of the literature written on the topic of mining automation has focused on the equipment level, specifically on removing the operator from production mining equipment. This focus should not, however, overshadow advances registered in automation at both the process and enterprise levels. Only at the operations level of the hierarchy has little progress been made. While automated equipment, process management and enterprise resource planning are a current reality; it is argued that the benefits from automation have, to date, been largely elusive. It is further argued that full benefits of automating other levels will only be fully achieved when this ‘gap’ in the mining automation hierarchy has been addressed and an uninterrupted, process-wide information flow across the entire operation is achieved. Furthermore, it will be reasoned that so-called vertical integration can only be achieved with an automated operational level in place. It is believed that all the necessary building blocks are in place and that the industry is ready for this development. The paper concludes by presenting a vision for what operational level automation would achieve.

Sep 1, 2001

By T. V. Owen

This paper describes the flotation of cassiterite from fine slimes at Rooiberg Tin Limited, and gives an of the Amdel on-line analysis system that was instaled in 1984 to aid in the control of the concentrate The system, which is easy to install and maintain, and which uses X-ray-fluorescence analysis, has improved control, and therefore a better recovery of tin.

Jan 1, 1988

By Harushige Kusumi, Yuzuru Ashida, Toshiki Watanabe, Toshifumi Matsuoka

ABSTRACT: The technique of various kinds of numerical analysis offered remarkable results to explication of many rock mechanical phenomena. These techniques regarded a rock stratum as a continuum body and solved the governing equation of continuum mechanics by using finite differ-ence method, finite element method and/or others. Using numerical analysis based on continuum mechanics, however, the simulations of destruction phenomena caused by elastic waves and on the other hand, the elastic wave propagation which generated by fracturing events are quite difficult. In this paper, we express a rock stratum by a granular body model and develop a simulation tech-nique can simulate both wave phenomena and destruction phenomena at once. The DEM (discrete element method) simulation results are compared with finite difference solutions of elastic wave equation. Furthermore, we simulate Hopkinson effect by this proposed method. Hopkinson effect is famous as a destruction phenomenon caused by elastic wave propagation. ABRISS: In dieser Studie drücken wird eine Felsschicht durch ein Granularkörpermodell aus und entwickeln eine Simulationstechnik, die sowohl Wellenphänomene als auch Zerstörungsphänomene simulieren kann. Die Ergebnisse der Simulation mit DEM (Diskrete-Elemente-Methode) werden mit denen der Finit-Differenz-Lösung von Gleichungen elastischer Wellen verglichen. Desweiteren simulierten wir den Hopkinson-Effekt mit dieser vorgeschlagenen Methode. Der Hopkinson-Effekt ist als Zerstörungsphänomen berühmt, verursacht durch Fortpflanzung elastischer Wellen. RESUME: Dans cette étude, nous exprimons un lit de roches par un modèle à corps granulaire et développons une technique, permettant de simuler d'un coup le phénomène des ondes et le phé-nomène de destruction. Les résultats de la simulation DEM (méthode d'éléments discrets) sont comparés aux solutions à différence finie de l'équation d'ondes élastiques. En outre, nous simulons l'effet d'Hopkinson par la méthode proposée. L'effet d'Hopkinson est connu comme phénomène de destruction, causé par la propagation d'ondes élastiques.

Jan 1, 2003

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By A. C. Mulholland

The electrical control of three-electrode submerged-arc furnaces suffers from a number of complexities, mostly due to the nature of the furnace electrical circuit providing power to the furnace where the three electrodes are interconnected within the furnace through the molten metal bath. This gives rise to what is known as the interaction effect 2, where variations in one electrode?s current can cause comparable changes to the currents in the other electrodes, particularly in larger furnaces with low power factor. Resistance-based control of the electrode penetration has largely alleviated these problems, since the resistance encountered by each electrode is predominantly dictated by the length and conductivity of the current path from the electrode?s tip to the molten metal bath, which acts as the three-phase circuit?s floating neutral point. Hence resistance changes due to tip position or conductivity changes beneath one electrode do not affect the resistances beneath the others, effectively decoupling the control of the individual electrodes1. Although resistance-based control is therefore generally accepted as superior to current-based control for the regulation of submerged-arc furnace electrode penetration, a few furnace operators still prefer to use current control under specific furnace conditions. This paper presents the results of analysing the performance of both current and resistance-based control in typical scenarios encountered on industrial furnaces, taking into account a number of factors including electrode penetration, power distribution, efficiency and asymmetry of the electrode currents. In order to accomplish this, three typically encountered scenarios were simulated. The results obtained show that resistance control provides more benefit in all cases, however, the uneven electrode current distribution generated by resistance control when electrodes are on top stops may cause some concern if baking of the electrodes is required in this scenario.

Jan 1, 2009

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By J Steyn

Block Cave mining is one method used to extract ore from underground diamond mines as well as other massive orebodies such as copper. This necessitates the excavation of many kilometers of tunnel within the ore body. The integrity of these excavations needs to be maintained over a number of years. Most Kimberlites and weak orebodies are extremely susceptible to degradation when exposed to moisture and the atmosphere. It is therefore essential that some form of weathering protection is applied as soon as possible after exposure. Conventional methods of weathering protection such as shotcrete do not easily fit in with the production schedule, hence the need for a more efficient system that could be applied immediately after exposure and serve as a temporary support or even as a permanent support medium. The main advantages of thin sprayed liners (TSL) compared to shotcrete are the ease of application, speed of application, early strength, much reduced transportation of material, less labour intensive and cost effectiveness. Several Thin Sprayed Liners suitable for various mining environments and geotechnical conditions are available and could be well suited as additional support the undercut level development in a block cave where this may be required. TSL offer a cost effective support solution as an alternative to shotcrete in areas where the building of a support structure is not a requirement.

Jan 1, 2008

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By J. A. Cox, R. P. H. Willis, J. R. Dixon, A. D. Pooley

The paper describes the issues that should be considered when introducing mechanization to a mining operation. In South Africa, traditional methods of mining are well entrenched after more than a century of mining. To successfully change from these methods requires an integrated holistic approach that considers all aspects of a mining operation including setting of objectives, selection of personnel, recruitment, training and remuneration policies, organizational design, mine design, equipment selection, maintenance philosophy, standards and procedures, and monitoring and control. The paper makes reference to experience gained during a variety of on-mine case studies in drawing generic conclusions and making recommendations.

Jan 1, 2004

By R. Meyjes, P. Davies

Keywords: Pyrometallurgy, furnace, smelter, engineering company Metix is a private smelter engineering company wholly owned by its management. Its main lines of business in the ferro-alloy industry being: - turnkey smelter projects (LSTK) - engineering, project, and construction management projects (EPCM) - specialised furnace equipment comprising: ? complete electrode columns, including forged copper pressure rings and contact shoes, as well as fail-safe slipping devices ? water-cooled roofs ? bus-tube systems ? feed systems ? cooling systems ? linings ? off-gas systems ? tap-hole drills & clay guns - furnace power supply systems - ore agglomeration & sinter plants - feasibility studies & due diligence reports - technical consulting for investment banks - project procurement & cost control Metix management experience includes around 130 combined years of contacts and experience in the South African smelter industries. Over 30 furnaces have been built, for processes including FeCr (high, medium, and low carbon), FeSi, FeMn (high and medium carbon), SiMn (ultra low carbon), Si metal, and FeV.

Jan 1, 2006

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003

Frank Michael Gowar Egerton was educated at Jeppe High School for Boys and the University of the Witwatersrand, both in Johannesburg. He holds a B.Sc. degree in mining engineering, and has attended numerous courses on management, finance, and industrial relations. In the Executive Development Programme run by the University's Business School in 1981, he was voted the student who had made the greatest contribution to the programme.

Jan 1, 1993

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

By R. Romano

Some topics, which difficult the effective use of RMR for dam foundations, are reviewed and a new geomechanics classification system, DMR (Dam Mass Rating), is proposed -as an adaptation of RMR- giving guidelines for several practical aspects in dam engineering and appraisal of dam foundation. On revise quelques problems qui ont fait difficile l’application du RMR pour les fondations des barrages. On propose un nouveau classification système, DMR (Dam Mass Rating)-comme un désarroi du RMR-qui donne recommendations pour quelques problèmes pratiques dans le projet et construction des barrages, et de ses fondations. Es werden einige die praxisgerechte Nutzung des RMR (Rock mass Rating) erschwerende Themen betrachtet und ein neues Geomechanisches Einteilungssystem, das DMR (Dam Mass Rating), eine Anpassung des RMR, vorgeschlagen. Daraus resultieren neue Richtlinien für verschiedene praktische Aspekte beim Dammbau und bei der Beurteilung von Dammunterbauten

Jan 1, 2003