Search Documents

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By J. C. N. Ashukem, F. Agyemang

One understudied area of environmental law is the socio-ecological impact of ownerless mines. This impact is particularly pronounced in resource-dependent regions like South Africa and Western Australia, creating significant rehabilitation challenges. This article hypothesises that effectively managed financial provision could be valuable for rehabilitating legacy mines. Using a qualitative, comparative methodology, the article analyses the financial provisions for mine rehabilitation in South Africa and Western Australia, focusing on statutory provisions, funding mechanisms, and rehabilitation outcomes. Key themes, such as context, measures, and outcomes, are explored to assess the effectiveness of each financial model. Purposive sampling is used to select case studies from both regions, and thematic analysis is applied to interpret the data. The analysis highlights the financial rehabilitation measures in both regions, providing a structured framework for ownerless mine rehabilitation. South Africa's approach, guided by the Mineral and Petroleum Resources Development Act (MPRDA) of 2002, depends on state budget allocations, leading to funding inconsistencies and slow rehabilitation progress. In contrast, Western Australia’s Mine Rehabilitation Fund Act (MRFA) of 2012 uses a levy-based system, ensuring continuous financial support for mine rehabilitation. South Africa's state-dependent model has led to delays in rehabilitating derelict and ownerless mines, while Western Australia’s funding model has facilitated steady progress. The article recommends that South Africa adopt a levy-based financial mechanism, strengthen legislative enforcement, improve financial oversight, and integrate proactive mine closure strategies to accelerate rehabilitation, reduce environmental hazards, and promote sustainable development in mining-affected communities.

Dec 15, 2025

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004

By D. Toporov, R. Abraham

"Gasification is a process of thermal conversion of solid carbonaceous materials into a gaseous fuel called syngas. Coal gasification is an efficient technology for a range of systems for producing low-emission electricity and other high-value products such as chemicals, synthetic fuels, etc.The paper presents the High-Temperature Winkler (HTW) gasification process, which is designed to utilize low-rank feedstock such as coals with high ash content, lignite, biomass etc. The process is characterized by a bubbling fluidized bed, where coal devolatilization and partial oxidation and gasification of coal char and volatiles take place, and by a freeboard where partial combustion and gasification of coal char take place.The recent development of the high-pressure HTW process is reviewed. Gasification of low-rank, high-ash coals with respect to gasification temperatures, conversion rates, and syngas quality is also discussed. The main HTW design steps required for an industrial-scale design are presented. Special attention is given to the process modelling, including global thermodynamic calculation as well as detailed CFD-based simulation of a reacting fluidized bed. Three-dimensional numerical results of the HTW process are also provided and discussed."

Jan 1, 2015

By L. Roux

The initial evaluation of a coal deposit often raises uncertainty with regard to the accuracy of the reported Resources and Reserves. Reconciliation of results from mining and beneficiation with the original raw field data highlights deficiencies in original estimations. Credible Resource and Reserve estimation forms the basis on which an entire mining enterprise is motivated, initiated, funded, and established as a commercially viable proposition. This is required for sustainable extraction purposes and to support vital downstream industries such as power generation. Accurate determination of the density of the matrix of the material being evaluated is the key to credible values being obtained for Resources and Reserves. Losses between 15% and 20% of the Resource/Reserve can be realized if incorrect densities are applied to the tonnage derivation. Coal plies and particles have different relative densities, determined by the maceral composition, rank, and mineral and moisture content. These factors in turn contribute to the moisture, volatile matter, ash and carbon contents of a coal, which affect the overall density of the raw coal. More specifically, the relationship of ash to density and the effective matrix porosity were found to be critical in solving the greater majority of the problems in predictive calculations. A major deficiency identified is the inability to determine effective porosity, allowing absorption of adventitious moisture and altering the mass of the core sample. Although the volume of the raw material is altered through crushing, the change in mass after controlled air-drying, used with the original geometrical volume of the raw material, provides a credible air-dry density and allows the determination of the volumetric change related to effective porosity. This parameter can be validated through the evaluation of proximate ash using the ash-adjusted algorithm and a correction for the inherent moisture applied to also give a credible relative density value for an air-dried sample. A combination of theoretical, empirical, and reconciliatory evaluations of the available data, taken from the exploration phase through the mining process to final production, has shown that an integrated approach using the ash-adjusted density (AAD) methodology, in conjunction with other evaluative techniques, provides credible results with a considerably higher degree of accuracy than is currently possible.

May 1, 2021

By Yuandong Qiao, Erdong Li, Chao Lv, Junjian Ye

The gas-based CO reduction of Panzhihua vanadium titanomagnetite concentrate from 1100°C- 1250°C was investigated in this paper. The reduction degree increased with increasing temperature and increasing reduction time. At a temperature of 1250°C and a reduction time of 20 minutes, the metallisation degree reached 92%. The iron-titanium oxide phase transformation during reduction process was Fe2.75Ti0.25O5→Fe2.5Ti0.5O4→FeTiO3→FeTi2O5 according to the X-ray diffraction analysis. The SEM and map scan by energy spectrum of results of reduced samples at different temperatures indicated that the metallic iron particle size increased gradually as the reduction temperature increased. These results can serve as a reference for the reduction of vanadium titanomagnetite by CO. Keywords: Vanadium titanomagnetite concentrate, CO reduction, phase transformation, reaction mechanism

Jan 1, 2020

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

The general standard of engineering in South Africa will, it is believed, reach new heights after the establishment of the S.A. Council for Professional Engineers (SACPE) in February, 1969. The Council is being created to establish standards for professional engineers in this country and ensure that the quality of engineering is maintained at a high level. In terms of the Act of Parliament under which the new Council will operate, all consulting engineers will have to be registered if they wish to remain in private practice. While engineers who are not in private practice cannot be compelled to register, it will be in their interests to do so, according to a statement issued by Mr M. R. Gericke, chairman of a Shadow Council which is at present preparing for registration and drafting the requirements for registration. Registration is seen as an important move towards maintaining the quality of engineering in South Africa. Engineers will be encouraged to strive for professional status by gaining the necessary qualifications and the varied range of experience required by the Council before registration. All work done by registered professional engineers will have to conform to certain minimum standards. A spokesman for the Council has urged all engineers to ensure that they apply for registration when the Act comes into force in February. The Council is also anxious to gain the co-operation of employers in ensuring that the holders of professional engineering posts will be registered. Full information regarding registration will be sent to engineers throughout South Africa early this year, and announcements will appear in the press.

By T. Mapeta, S. M. Rupprecht

Discussions on reasonable prospects for eventual economic extraction (RPEEE) include the CRIRSCO 2019 reporting template, JORC 2012, SAMREC 2016, CIM 2019 Guideline, and Regulation SK-1300. These reporting codes all conform to the principles of reasonable prospects for eventual economic extraction. To demonstrate that all mineral resources align with the RPEEE principles, the Competent Person is responsible for endorsing the mineral resource estimate. Moreover, establishing mineral resources and RPEEE requires technical input from numerous technical specialists, such as mining and geotechnical engineers, metallurgical engineers, social and environmental specialists, financial and governmental practitioners, and more. The aim is to improve the transparency of the disclosure of mineral resources and guarantee the investor or potential investor that the reporting of mineral resources is based on reliable technical, economic, environmental, social, and other relevant factors. This paper discusses the important protocols and definitions in some international reporting codes for the purposes of developing a guide memoire that will assist the Competent Person to interpret, establish and apply RPEEE appropriately and easily.

Jun 27, 2025

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

By R. V. Peche

Since 1952, Bond’s equation has been used as a standard to predict the specific energy of grinding for a given duty. The Bond’s equation considers that the exponent is constant for all conditions. Hukki, in 1961, pointed out that the exponent is a function of the particle size, and concluded that the Bond’s equation applies successfully for an intermediate range of sizes; out of this range the Bond’s equation leads to high error as demonstrated in this paper. More recently, in 2004, S. Morrell presented a new formula in which the exponents vary with the feed and product size. This paper is based on Hukki’s approach and presents a new general formula, in which the exponent varies only with the feed particle size. This new equation has been proven in 82 observable cases in Peru and other countries around the world, involving ball mills and vertimills in different configurations over a wide range of feed and product sizes, work indices and mill diameters; in most cases, the predicted value has an error less than 10% with regards to the observed value and no need for any correction factor. Keywords: Grinding, specific energy, particle size, work index, variable exponent

Jan 1, 2020

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, J. M. A. Geldenhuis

The successful application of solid electrolytes in electrochemical cells for high-temperature thermodynamic studies depends to a large extent on an accurate knowledge of the P. value of the electrolyte (the oxygen partial pressure at which the ionic conductivity and n-type electronic conductivity of the electrolyte are equal). Consequently, the P. value of an electrolyte must be determined prior to its use in electrochemical cells. This paper describes the successful application of a coulometric titration technique in the quantitative assessment of the P. values of a commercially available ytria-stabilized zirconia electrolyte that has been used extensively by local investigators. The experimentally determined P. values of the electrolyte are reported and compared with P. values reported in the literature for a similar electrolyte.

Jan 1, 1988

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By J. Petersen, K. Shaik

The traditional route utilised for the recovery of Platinum Group Minerals (PGMs) in South Africa involves the concentration of ore by flotation, followed by smelting to produce a PGM rich matte, which is then digested hydrometallurgically to solubilise base metals and Platinum Group Elements (PGE). HCl/Cl2 is conventionally used for PGE dissolution from concentrated material, which is an aggressive reagent associated with high maintenance costs as well as environmental concerns. Of interest is the leaching of PGMs directly from mineral ores, low grade concentrates and tailings in a cyanide-ferricyanide system as a more sustainable alternative. This system has shown favourable Pt recoveries among the Pt minerals, but with sperrylite (PtAs2) displaying highly refractory behaviour. The dissolution of sperrylite is investigated in a cyanide-ferricyanide system in the context of an electrochemical study involving OCP, chrono-amperometry and cyclic voltammetry. This approach allows the assessment of leaching characteristics as well as the investigation of surface passivation, which is believed to contribute to poor Pt recoveries. Some evidence is presented that such passivation is related to the formation of arsenide species on the mineral surface. Keywords: Sperrylite, PGMs, cyanide, ferricyanide, electrochemistry

Jan 1, 2020

By A. Della Rocca, P. Jonker, B. Henning

Successful prediction of the collection efficiency of cyclone separators is a necessary step in cyclone design and verification. Aside from standard empirical relations, CFD modelling is widely adopted to supplement the design of cyclone units in relation to the desired separation performance. Nevertheless, effective adoption of numerical modelling is sometimes prevented by large modelling errors, especially for small size particles which are more subject to turbulence effects than larger particle classes. In the past, this motivated the adoption of more refined turbulence modelling approaches, such as large-eddy simulations. These approaches provide greater insight into time dependent behaviour, while leading to larger computational cost with respect to more standard approaches. In this paper, an effective Eulerian-Lagrangian Reynolds-averaged Navier-Stokes (RANS) approach is investigated, which is able to predict the complete separation efficiency curve with satisfactory accuracy, without requiring prohibitively long computational times. An assessment of the proposed approach is carried out against experimental data from large laboratory scale cyclones, in the form of mean and fluctuating velocity profiles from LDA measurements (Hoekstra, 2000), as well as with respect to the experimental separation curve (Zhao, 2005). The final application to a full-scale industrial cyclone unit is then carried out with the aim of tuning the cyclone design to the separation efficiency curve as required by downstream processes. Keywords: Cyclones, separation, CFD, RANS, RSM, Lagrangian

Jan 1, 2020

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been 29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

By Gift Makusha, Dave Minney

Anglo Coal South Africa mines coal for both the domestic and export market using open cast and strip mining methods. To establish a mine, a process is set in place to gather ever increasing amounts of geological and metallurgical data to confirm a proven reserve. Increasingly, geotechnical data are also included in this process to confirm that reserve is easily and safely mineable. The mine design process is an iterative one using a combination of numerical modelling and empirical data to arrive at a mining layout that is both, practical, productive and safe. In South Africa it is a legal requirement to compile a code of practice to combat rock fall and slope instability accidents and these have to be revised annually, reinforcing the iterative process of continual improvement. To ensure best practise occurs, all Anglo Coal operations are subjected to annual 2nd party audits and ad hoc 3rd party audit by independent consultants. This paper attempts to explain the process described above in a concise, but understandable manner. 1.0 GEOLOGICAL SETTING The Ecca sediments date from the Permian period and the coal deposits were formed in glaciated valleys on a basement of Dolomite, Ryolite or Granophyre rock types. The sediments overlying the coal deposits are typically flat lying and multiple bedded. The sediments consist of mudstones, shales and sandstones and are generally capable of forming stable highwalls given the time that they must stand up for. Anglo Coal extracts coal from the Witbank, Highveld and Vereeniging coalfields. The Witbank coalfields contain five seams numbered from the base upwards, 1 to 5 Seam; Highveld coalfield the 2 and 4 Seam and the Vereening area the seams are described as Top, Middle and Bottom seams. Coal deposited over the basement Dolomite formation display very erratic dips, as contemporaneous subsidence occurred in some instances over sinkholes that were forming, resulting in local thickening of the coal deposit and resulting in strata that dips toward the centre of the sinkhole.

Jan 1, 2006