Search Documents

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By C. M. Rule

Energy efficiency is currently a significant area of interest due to the Eskom power situation, which led to severe power impacts to the PGM, and indeed whole SA primary industries, in early 2008. Anglo Platinum has focused on energy efficiency for a number of years, especially in the concentrator operational area. New comminution technologies have been aggressively developed, which have shown real metallurgical efficiency gains as well as significant energy efficiency and saving potential for Anglo Platinum?s total electrical consumption as the company expands into a growing PGM demand market. This paper illustrates this programme?s activities, potential and considerable achievements to date.

Jan 1, 2009

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

By D. Diering

Having agreed to perform this task, I naturally started to wonder what on earth I was going to talk about, and on reviewing the literature I was surprised at how little I knew and how much I?d forgotten about the origins of this industry. For example: ?I?d forgotten that the Chinese invented black powder at least 1 000 years ago, back in the 10th century (although some say this invention occurred 2 000years ago). ?I didn?t know that Roger Bacon was the first person in the Western World to give exact directions for the making of gunpowder in 1242 and to understand its potential. Pepper?s Playbook of Metals quotes:?...above all, he is named as the discoverer of gun-powder, a material which has brought more wonderful changes in the great family of man than the most potent elixir that could have been devised to prolong life?.

Jan 1, 2000

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By N Morales, G Nelis

Short-term plans must meet the long-term goals while accounting for shovel selectivity, operational space, and scheduling restrictions. There are several approaches that deal with these issues to deliver a feasible short-term schedule. This paper compares two approaches based on mathematical programming to address the short-term mining cut definition and scheduling in an integrated way. They work by scheduling extraction to comply with long-term production goals, but they differ in how mining cuts are modelled. The first approach schedules Selective Mining Units (SMUs) but aggregates them around predefined locations. The second approach does not work on SMUs; it decides directly what mining cuts are to be used from a pre-defined set of shapes. It assigns a destination and schedules the extraction for the selected mining cuts. We applied both approaches in a real case study to compare their results in terms of profit, mining cut design, expertise needed, profit, and optimisation performance.

Sep 1, 2021

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By M. J. Lukhele

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree A number of high wall mining methods were developed over the years to mine coal reserves exposed on the high walls created during surface mining. The auger mining system was initially developed in the early 1940s in the United States of America. High wall mining is a method of recovering coal from seam exposed either by mechanical excavation methods or natural erosions. This is usually associated with strip-mining (opencast) where the stripping ratio is high and uneconomical to mine using the opencast mining method. This paper discusses the surface auger mining as deployed at Rietspruit Mine Services Proprietary Limited.

Jan 1, 2002

By Y. F. Bulgakov, Y. V. Melnikova, V. S. Zakharov

A new technology of atmosphere in inertization of fire section with the help of gazeous nitrogen is presented in the report. This technology is based on membrane air subdivision into two streams, concentrated with nitrogen (up to 99%) and with oxygen correspondently with subsequent giving them into the place of fire. This technology belongs to environmentally friendly ones and it has a great number of technical, mobile and economic advantages comparing with the rest of well-known methods of fire extinguishing. This technology application in Ukrainian coal mines allowed to reduce the member of isolated places of fire at the expense of their extinguishing efficiency.

Jan 1, 2003

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015

Paper written on project work carried out in partial fulfilment of BSc Engineering (Mining) The aim of this project is to determine whether certain pillars occurring within the no. 1 shaft and no. 2 sub-shaft ground are feasible for extraction. The extraction of these pillars is essential in prolonging the life of Kloof Main Shaft as its VCR resource becomes depleted. Extraction of these pillars will require a combination of designs and factors, with rock mechanics and ventilation being the main considerations. Primarily for the pillar extraction, an initial production target of150 kg gold, mine able in one year from commencement of ?opening up? was set. The planned target has been exceeded and the feasible pillars identified are expected to yield an additional 1 390 kg of gold to the shaft?s production profile. However, not all the required ventilation designs have been completed to date, the reason being that at the time of the project, many of the pillar areas were inaccessible and thus ventilation conditions are unknown. This project is therefore an ongoing process and will require further design once all targeted pillar areas have been opened up. A preliminary costing analysis of the pillar mining was performed and it was found that all targeted pillars with the exception of 38?61 pillar are profitable.

Jan 1, 2005

Comminution is a vital part of minerals extraction, and therefore of the South African economy. The high cost and throughput-limiting nature of comminution forms a strong motivation for research directed at improving the efficiency of the process. Building on a ten year background of fundamental charge motion research, a new formal UCT flotation and communication group has been formed. The group is also moving strongly into the field of milling circuit modelling and simulation, based on close links formed with the Julius Kruttschnitt Mineral Research Centre (JKMRC) of Australia, and an international collaborative research programme.

Jan 1, 1998

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

A new system for granting access to mineral rights is proposed in the recently released White Paper, ?A Minerals and Mining Policy for South Africa?. Official policy states that ?Government?s long-term objective is for all mineral rights to vest in the State for the benefit of and on behalf of all the people of South Africa?. In order to achieve this objective, government is presently investigating the feasibility of imposing a financial or tax-related disincentive to holding mineral rights. The paper aims to present the pros and cons and to examine the alternatives which will cause minimal disruption to the minerals industry in the period during which mineral rights are transferred to the State. South Africa is a country whose economic and political history is embedded in the development of its mineral resources and has inherited a system which cannot simply be wished away. Hasty or radical decisions will compound the problem, rather than provide a lasting and widely acceptable solution. Mineral rights ownership and its impact on access to mineral deposits are discussed. Taxation as a possible economic disincentive is also evaluated. Finally, the value of mineral resource related information as a prerequisite to mineral policy decisions and as an alternative to mineral rights taxation is emphasized.

Jan 1, 1999