Search Documents

By J. H. Potgieter

This paper describes two cases of corrosion that occurred in dry-process, rotary, cement-clinker kilns. In the case of the kiln with five pre-heater stages, the attack occurred primarily from sulphates that probably originated in the raw feed and fuel being used in the plant and that penetrated the refractory lining. The corrosion was similar to ash-deposit corrosion often observed in steam boilers. In the second case the plant consisted of a long dry kiln with a single pre-heater fitted to the feed-end. In this case the corrosion could be ascribed to alkali chloride penetration through the refractory-brick lining and subsequent hot corrosion of the kiln shell.

Jan 1, 2004

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

Instability in rockpasses at deep levels often initiates as a result of stress induced fracturing of the rock on the walls of the pass. This may then progress to a stage at which the geological structure of the rock mass becomes dominant and permits large joint-defined blocks and slabs to become unstable. In this paper, a technique is described in which jointing parameters and their variabilities?orientations, spacings and lengths?are taken into account in estimating the extent of failure that may develop around a typical unsupported deep level gold mine rockpass. The results of this prediction are compared with the results obtained from a review of pass performance in the gold mining industry.

Jan 1, 2005

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By I. R. Firth, D. L. Taylor

Metal mining operations, in particular gold mining operations, use intensive ore control procedures in order to manage the extraction of ore zones from benches containing both ore and waste material. Typical grade control procedures rely on blast hole samples to indicate ore grade. Statistical techniques and geological controls are then used to create two-dimensional polygons, which indicate zones of material designated as ore. These ore-polygons are calculated using pre-blast material locations and are generally not corrected for rock movement caused by blasting. This lack of correction appears to exacerbate the material mischaracterization problem of sending ore to the waste dump and/or waste to the mill. One Nevada gold mining company has estimated that this could be a $10 million per year problem for their operations. Using a simplified vector field algorithm, a method of taking point movement data and interpolating post-blast positions for all nodes in a polygon has been developed. Currently working in 2-dimentions (X-Y), this algorithm utilizes the movement vectors calculated from pre-and post-blast positions of targets placed in a blast, to generate a spatial transformation function for any point on the bench. This transformation is then applied to the nodes of the ore-polygons to produce modified dig lines ore polygons reflecting distortion and movement resulting from the blast. The method as implemented uses common mine planning routines and is performed using the Surpac software suite. The method may be adapted to use any pre-and post-blast point movement data available, and most mine planning suites include the simple interpolation algorithms used. Keywords: Blast movement; Ore control; Open pit blasting; Grade control

Jan 1, 2003

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By L. Forsbacka, L. Holappa

Viscosities of quasi-ternary CaO-SiO2-CrOxmelts in contact with metallic chromium were measured by the rotating cylinder method up to 1750ºC. Twelve slag compositions were selected in the composition range 20–55 wt% SiO2, 10–45 wt% CaO and 10–60 wt% CrOx. Estimation of the amounts of CrO and Cr2O3was made by regression analysis based on the earlier data. Professor Iida’s (Osaka University) viscosity model was applied and model parameters (0CrO,CrOand Cr2O3) were evaluated. The Iida model gave good consistency with the measured viscosity values.

Jan 1, 2004

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

By H. J. Glass

Collection, preparation, and analysis of blasthole chippings is expensive. Frequently, interpolation of grades at unsampled locations is considered using techniques like kriging. A pre-requisite for kriging is that an experimental variogram is established. In order to assess the quality of the experimental variogram, a measure is developed in this paper. The measure is derived from analysis of the time-honoured expression relating the variance, semivariance, and covariance. It reflects the weighted average deviation of the summed semivariance and covariance from the biased variance. The proposed measure allows assessment of the influence of key variables on the quality of the variogram. Using simulated data, it follows that the quality improves with an increasing number of samples, increasing density of the sampled locations, increasing regularity of the sampling pattern, and increasing uniformity of grades in the absence of correlation. Application to real data shows that the minimum number of samples could coincide with a marked decrease in the value of the measure. Establishing a threshold value is subject to further research. Keywords: variogram, variance, covariance, semivariance, minimization, sampling.

Jan 1, 2003

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By J. T. Kalala

Energy consumption and wear of grinding media and liners are the major cost factors in milling plants. Since the beginning of the last century, much effort has been directed at the prediction of the power draw as affected by the mill operating conditions. This paper explores the prediction of the liner wear using the discrete element method (DEM). A mathematical model taking into account adhesion, abrasion and impact wear which occur in dry mills is derived in order to predict the loss of material on liners. The mathematical model is implemented in the DEM code using an objective function in order to produce realistic simulated profiles. Our DEM simulated predictions are compared to published experimental and industrial data. Keywords: modelling; discrete element method; liner wear

Jan 1, 2004

The additive property of dispersion variances was found experimentally by D.G. Krige using data from the gold deposits of the Witwatersrand. In this property, called ?Krige?s relationship?, the dispersion of a small unit, v, within the deposit is equal to the sum of the dispersion of v within a bigger unit, V, and the dispersion of these units, V, within the deposit, D. It is known that the variance of the grades decreases as the support increases, the so-called volume-variance relationship. To analyse volume-variance and Krige?s relationship, the methodology herein proposed combines blending piles and geostatistical simulation to simulate the in situ and the pile grade variability. Variability reduction in large piles is based on the volume-variance relationship, i.e. the larger the support, the smaller the variability (assuming perfect mix). Based on a pre-defined mining sequence to select the blocks that will form each pile for each simulated block model, the statistical fluctuation of the grades derived from real piles can be simulated. Using this methodology, one can evaluate within a certain time period the expected grade variability for various pile sizes, and also calculate the Krige?s relationship between the small blocks and the piles of different sizes. A real case study using a large Brazilian iron ore deposit illustrates the methodology and demonstrates the validity of the results.

Jan 1, 2014

By N. Reddy

The influence of local geology and rock mass characteristics on deformations during a rockburst caused by a controlled blast was studied. This was done by means of visual examination, mapping and photography both before and after the blast. We found that the ejected material was bounded mostly by fractures associated with the bow-wave fracturing and bedding surfaces and that existed prior to the blast. Most of the damage was caused by shake-out. This information is important input for the design of rockburst resistant support systems under conditions of moderate stress.

Jan 1, 2001

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton's JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton's empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d'évaluer JRC qui est un indice de rugosité superficielle d'une fracture de roche à l'aide du modèle de fracturation, compte tenu de son effet d'échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d'une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l'aide de la formule empirique Barton sur la base des résultats de l'essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d'évaluer l'échelle d'endentement d'une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d'évaluation de JRC par rapport au profil JRC.

Jan 1, 2003