Search Documents

By G. van Aswegen

Large structures in mines (faults, dykes, pillars, abutments) fail when the load exceeds the strength. If the loading system stiffness (LSS, also referred to as the ‘local mine stiffness’) is lower than the stiffness of the structure the failure will be unstable. The greater the difference between these stiffnesses, the greater the energy release during unstable failure. A method has been formulated by which the LSS is established through cost-effective numerical modelling while insight into the structure stiffness (source stiffness - SS) is provided by apparent stiffness, a parameter based on the empirical relation between seismic moment and radiated seismic energy of small seismic events from the area/volume of interest. By plotting LSS vs SS a ‘stiffness diagram’ is constructed that is useful for seismic hazard ranking of different structures. A comparative back-analysis of the Dagbreek fault in Welkom, South Africa, (source of the 1990 Matjhabeng earthquake) and two other nearby faults confirm the applicability of the method. An extension of the method, where ‘hazard magnitude’ is used as a measure of the LSS, allows a ‘stiffness diagram’ to be constructed using seismic data only. Les larges structures dans les exploitations minières (failles, dikes, piliers, culées) s’écroulent lorsque la charge dépasse la résistance. Si la raideur du système de chargement (LSS, aussi appelé la « raideur de la mine locale ») est plus basse que la raideur de la structure, l’éboulement sera instable. Plus la différence est grande entre ces deux raideurs, plus l’énergie dégagée pendant l’éboulement instable est grande. Une méthode a été formulée selon laquelle le LSS est établi par modélisation numérique rentable, tandis que la raideur de la structure (SS – raideur de la source) est établie par la raideur apparente, un paramètre basé sur la relation empirique entre le moment sismique et l’énergie sismique radiée de petits moments sismiques dans l’aire/volume en question. On trace le « diagramme de raideur » en relevant les deux mesures (LSS et SS), ce qui est utile pour classer les risques sismiques de structures différentes. On vérifie l’applicabilité de la méthode en comparant la faille de Welkom, Afrique du Sud (foyer du séisme de Matjhabeng en 1990) avec deux autres failles proches. Une extension de cette méthode, dans laquelle on utilise la « magnitude du risque » comme mesure du LSS, permet de construire le « diagramme de raideur » avec des données sismiques seulement. Große Strukturen in den Gruben (Verwerfungen, Dämme, Pfeiler, Auflager) scheitern, wenn die Last die Stärke übersteigt. Wenn die Steifheit des Ladesystems (LSS, auch bezeichnet als `lokale Grubensteifheit’) niedriger ist als die Steifheit der Struktur wird der Bruch instabil. Je grösser der Unterschied zwischen diesen Steifheiten, desto grösser die Energiefreigabe während des instabilen Bruches. Es wurde eine Methode formuliert, durch die das LSS durch eine kosteneffektive numerisches Modell erstellt wird, während ein Einblick von der offensichtlichen Steifheit in die Struktursteifheit (Quellensteifheit - SS) gegeben ist, ein Parameter der auf der emipirischen Relation zwischen seismischem Moment und ausgestrahlter seismischer Energie von kleinen seismischen Ereignissen vom Interessens-/Volumenbereich basiert. Durch das Kartograpahieren der LSS in Bezug auf die SS wird ein `Steifheitsdiagramm ' konstruiert, welches für seismische Gefahrklassifizierung der unterschiedlichen Strukturen nützlich ist. Eine vergleichende Postanalyse der Dagbreek Verwerfung in Welkom, Südafrika, (Zentrum des Matjhabeng Erdbebens 1990) und in zwei anderen nahe gelegenen Verwerfungen bestätigen die Anwendbarkeit der Methode. Eine Verlängerung der Methode, in der die `Gefahrengröße' als Maß für das LSS verwendet wird, gestattet, daß ein `Steifheitsdiagramm' konstruiert wird, welches nur seismische Daten verwendet.

Jan 1, 2003

By R. J. Hundermark

Keywords: Anglo American, Anglo Platinum Ltd, Waterval, Mortimer, Polokwane, ACP, pyrometallurgy, platinum, PGMs Anglo Platinum Ltd is the largest primary platinum producer in the world and operates three smelters in South Africa: Waterval, Mortimer and Polokwane. The operational details of the smelters are covered in previous reviews, thus only unit operations that have been upgraded are discussed. The most significant of the upgrades include the installation of a second ACP converter at Waterval Smelter in 2006 and the anticipated upgrade of Mortimer Smelter to 38MW in 2011. Several advances have been made in the smelting operations to improve the furnace stability and longevity. Control of the chromium input to each of the smelters has substantially allowed continued operations at levels below the spinel saturation point in slag, which results in lowered matte and slag temperatures. Mogalakwena concentrate, arising from the Platreef ore, is used to dilute high chromium-containing concentrates. In addition, furnace controls have improved in terms of crucible temperature and condition monitoring, improved feeding control, management of alarms and trips and having the quality of instrumentation and operational rigour required to support this. Advances have been made on the ACP converter in terms of good converter matte quality, and increased intensity and efficiency of operation. Combined with improvements to both the conventional and tower sulfuric acid plants, the emissions from Waterval Smelter have been reduced substantially since the introduction of the ACP. This is in spite of increasing metal throughput. The Anglo Platinum Ltd smelting operations have made significant progress since 2006 and further advances are envisaged to further improve on safety, reduce costs, increase efficiencies and throughput, while reducing emissions.

Jan 1, 2011

By S. Sakurai, N. Shimizu

The stability of slopes is a crucial problem not only in open pit mines, but also in civil engineering situations. The deformational behaviour of slopes is in general monitored during/after the excavation by carrying out field measurements where displacement measurements are commonly adopted. In monitoring the slope stability it should be emphasized that the measurement results must be properly interpreted so as to assess whether the slopes are stable or become unstable in the future. In order to interpret the data, back analysis is extremely useful. In this paper a slope stability monitoring system is described. It consists of displacement measurements by GPS, and a back analysis of measured data. The use of GPS has a great advantage, because of the fact that continuous displacement measurements with high accuracy for a large extent of concerned area can be easily achieved. On the other hand, the back analysis can reveal the mechanical characteristics of the ground, which make it possible to assess the stability of slopes quantitatively.

Jan 1, 2006

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By H Möller

The purpose of this paper is to give an overview of the corrosion behaviour of steel in seawater. It is shown that the corrosion products (oxy-hydroxides and calcareous deposits) that are formed during corrosion in seawater have a significant effect on the corrosion behaviour of steel. The chemical composition of the steel determines how protective the oxy-hydroxide corrosion product is. The composition of the seawater influences the nature of the calcareous deposits. This needs to be considered when artificial solutions are used to simulate the corrosion behaviour of steel in seawater. A 3.5% NaCl solution is used frequently for this purpose, but because no calcareous deposits can be formed in this solution, erroneous results in terms of corrosion rates are obtained. The more complex ASTM D1141 artificial solution can be used to include the effects of ions other than Na+ and Cl- in synthetic seawaters. The importance of these other ions on the formation of calcareous deposits is discussed. Keywords: Steel, corrosion, seawater, calcareous deposits, oxy-hydroxides

Jan 1, 2006

By S. J. Frank

Ferroalloy furnaces are well known to be extremely difficult to control from a metallurgical perspective. Mostly metallurgical control is still reactive in nature, causing a significant amount of reworking and product blending to achieve a proper product specification. Despite numerous efforts towards the model based control of primary smelting operations, actual metallurgical feed forward control seems to remain elusive. One of the key reasons in the failure to model these metallurgical reactors well, is that fundamentally orientated pyrometallurgists, statisticians, data miners and control engineers very often have diverging ideas how to model these systems. Furthermore, metallurgists have often come to rely on their ability to develop empirical regression models of furnace behaviour, as they have lost their faith in the ability of thermochemical and metallurgical engineering fundamentals to accurately predict the outcomes from furnaces. This paper shows how good thermochemical modelling can be combined with proper technological and systems analysis, as well as a proper inventory model, to predict the alloy and slag chemistry with good accuracy one tap into the future, at a time horizon of typically around 4 to 6 hours. For this modelling approach, a number of tools will be used, such as data reconciliation, thermodynamic modelling using Fact Sage®, inventory and heel estimation, neural networks and statistical data exploration. Furthermore, systems identification theory will be combined with the approaches given above to develop a truly dynamic predictive model. This paper seeks to demonstrate the need for a hybrid approach, which incorporates plant data and readily accessible thermodynamic data to develop a proper dynamic model.

Jan 1, 2004

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By S. E. Olsen, K. Tang

The complex heterogeneous equilibria associated with the production of manganese ferroalloys have been simulated by employing recently developed thermochemical databases. The non-ideal Mn-Fe-Si-C alloy and the MnO-SiO2-Al2O3-CaO-MgO-FeO slag system have been modelled separately by the compound energy and cellular model. A large number of experimental thermodynamic and phase-equilibrium data were used to evaluate the model parameters for the liquid and solid Mn-Fe-Si-C phases. In addition to the liquid metal phase, solid mixture phases occurring in the Mn-Fe-Si-C system have also been studied. Over 500 measured equilibrium data have been utilised to verify and calibrate the model calculations. The paper will present typical simulation results, from activities of components to multicomponent heterogeneous equilibria. Good agreements can be obtained for many important technological parameters such as carbon solubility, phase relations and equilibrium diagrams, element distribution as function of temperature and slag composition etc. Application of the present models to the silicomanganese production will be demonstrated in this paper.

Jan 1, 2004

By L. du Preez, J. D. Steenkamp

This paper introduces the concept of clean steel production from a pyrometallurgist’s perspective to the broader metallurgical community. A simplistic overview of the steelmaking process from iron ore to car body manufacturing is followed by an introduction to the South African steel industry and the technologies that it utilizes. The process is illustrated by an overview of the flow sheet and technologies for the production of clean steel at Saldanha Steel, South Africa.

Jan 1, 2015

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By J. Muralha

The paper presents the limit equilibrium equations for the analysis of toppling blocks on a rock slope. The safety conditions are assessed by a numeric procedure implemented in an Excel worksheet. The UDEC numerical program was exploited to validate the procedure. A probabilistic model considering the spacing variability of the discontinuities was developed to define the most relevant parameters in this kind of problems. La communication presente les equations d’équilibre limite pour l’analyse de blocs rocheux sur une pente. Les conditions de securité sont évaluées par une procédure numérique en Excel. Le logiciel UDEC a été exploité pour valider cette procedure. Un modèle probabilistique a été developpé pour définir les plus importants paramètres dans ces problèmes. Das Referat stellt die Grenzgleichgewichtsgleichungen für die Analyse von umstrürzenden Blök-ken auf eines Felshang vor. Die Sicherheitsbedingungen werden durch ein numerisches Verfahren mit Excel beurteilt. Um die Gültigkeit des Verfahrens festzustellen, wurde das Programm UDEC benutzt. Ein die Klufabstandsvariabilität berücksichtigendes probabilistisches Modell wurde entwickelt, um die wichtigsten Parameter dieser Probleme zu bestimmen.

Jan 1, 2003

By K. Kotwica, P. Gospodarczyk, J. Sosnica, J. Pawlik, Z. Iwulski, K. Pawlik

The paper presents problems resulting from the mobile mining machines functioning and requirements concerning a machine control system, which controls successive operation stages of such machines. The problem is presenting on the example of a mobile hydraulic support to remove residual pillars in copper ore mines. The paper describes an algorithm and a flow chart to be followed when designing a supports control system. Design of control systems to ensure machine function under given circumstances is also presented.

Jan 1, 2003

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By J. Björkvall, S. Ångström, L. Kallin

In this paper results from industrial trials of CaC2 injection during stainless steel production in an electric arc furnace at Sandvik Steel is presented. The main purpose of the investigation was to analyse the effect of the injection on slag foaming and final chromium oxide concentration in slag. The results show that both an increase in slag foaming and a decrease of the final chromium oxide could be obtained during the charges with CaC2injection. On the basis of the results, the economical requirements are also discussed. Both the technical and economical requirements could be achieved for steels alloyed with Mo. In order to secure the economical requirements for all steel grades of interest, the injection technology must be further developed. It would also be important to utilize the positive effect of the slag foaming on the electric energy consumption. The work has been performed as a part of MEFOS frame research programme with participants from Sandvik Steel, AKZO Nobel and Avesta Polarit. Keywords: stainless steel, EAF, slag foaming, injection, CaC2

Jan 1, 2004

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By Christopher J. Oates

Overview ? Mining Codes ? Best Practice ? Mining Standards Guidelines ? Get it right from the start ? External Auditors ? The 5% rule ? MMCRM's - The Key Components ? The MMCRM Report / Certificate ? MMCRM's & Round Robins ? Summary

Jan 1, 2005

By S. T. Camagu, J. Dutta Majumdar, S. L. Pityana

Laser surface alloying was used to develop copper and molybdenum aluminides by injecting premixed copper and molybdenum powder particles into a laser-generated melt pool on an aluminium substrate. Different laser processing parameters were used to produce the composite thin layers on the substrate material. The microstructure and phase constituents of the composite layer were studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Experimental results show that the matrix structure of the metal matrix composite layer consists of ?-CuAl2and MoAl5. Surface hardness was increased by a factor of 3.

Jan 1, 2015

SABS quality mark for explosives* AECI Explosives and Chemicals Limited has been awarded the SABS permit to apply the SABS standardization mark to al its permitted NO explosives manufactured at Modderfontein.

Jan 1, 1989