Search Documents

By S. J. Moema, M. G. Maruma, L. A. Mampuru, M. E. Maja

"The most commonly used high-chromium white cast iron (HCWCI) is the hypoeutectic white cast iron that contains 2–3.5 wt.% C and 10–30% Cr. This type of material relies on hard, brittle M7C3 carbides to impart good wear resistance. Due to its good wear resistance, this material has found application in the mining industry and cement industry. However, it has low fracture strength and this challenge led to research aimed at refining the microstructure. This was done by the addition of niobium in the range between 0.1 and 0.6 wt.%. In the as-cast condition, the addition of niobium was found to increase the fracture strength due to the finer eutectic microstructure. The hardness was also found to have increased slightly compared to the reference alloy with no niobium additions. Low fracture strength after heat treatment was observed in the Nb-added HCWCI, which is believed to have been caused by the precipitation of secondary carbides and the transformation of the matrix from austenite to martensitic. IntroductionFor the past few years Mintek has been involved in a project in which a number of alloys have been identified for grinding media applications. The high-chromium white cast iron (HCWCI) alloys were among the alloys researched for this application. The knowledge acquired from the grinding ball media research has now been extended to mill liners, which have traditionally been made of manganese-, chromium- and chrome-molybdenum steels. The replacement of worn mill liners costs the mining industry a significant amount of money and this has led to a need for continuous research to prolong the life of the liners. During milling operations, liner wear has an adverse effect on the capacity of the mill, the energy efficiency and milling efficiency and finally leads to relining, to replace worn liners."

Jan 1, 2016

By S. O. Choi, H. -S. Shin, W. -K. Song

Nuclear waste should be disposed with the best warranty for the national health and welfare. Among the several repository systems, the deep underground disposal is considered to be a most suitable system in Korean peninsula. However it demands basically the comprehensive stability analysis such as the behaviour of discontinuities in rock mass, the behaviour of ground water, and the reaction of rock stress according to the heat from the nuclear waste. For these purposes, the underground nuclear waste disposal repository was simulated in two- and three- dimensions. It shows that emphasis will be given to the thermal conductivity of discontinuities and the thermal convection of ground water as well as the thermal stress generated by the nuclear waste for design and construction of repository system, and they should be obtained from the field measurements. Déchets nucléaires devront tre déposés avec la meilleure garantie pour la santé et le bien public. Parmi les plusieurs systèmes de dépôt, la disposition en souterrin profond est considérée au système le plus approprié en Corée. Pourtant ce système demande essentiellement l’analyse éten-due de stabilité comme le comportement des discontinues en masse rocheuse, le comportement de l’eau souterrin et la réaction des contraintes de roche selon la chaleur depuis les déchets nucléaires. Pour ce but, le dépôt des déchets nucléaires en sous-sol a étè simulé en deux et trois dimensions. Il montre que l’accent sera donné à la conductivité thermale des discontinues et la convection thermale de l’eau souterrin aussi bien que la contrainte thermale générée par les déchets nucléaires pour le plan et la construction du systèmes de dépôt, et ils devront tre obtenus depuis les mesures sur place. Die Kernwüste muß mit der besten Gewähr für die nationale Gesundheit und die Wohlfahrt angeordnenet werden. Unter einigem Fundgrubesystem, das tief unterirdisch Wegwerfen werde in Betracht das passendest System in der koreanisch Halbinsel gezogen. Jedoch, es verlangt grundzätzlich die umfassend Stabilitätsberechnung so wie das Behnehmen mangelnder Konti-nuität in der Felsmasse, das Behnehmen des Grundwasser, und die Reaktion der Felsenbelastung nach der Hitze von der Kernwüste. Für diesen Zwecke, die unterirdische Wegferfenfundgrube der Kernwüste wurde in der zwei und drei Dimensionen gesimuliert. Es beweist daß die Betonung wird zur thermisch Leitfähigkeit mangelnder Kontinuität und thermisch Konvektion des Grund-wasser sowie die thermisch Belastung ergezeugt durch die Kernwüste für den Entwurf und die Konstruktion des Fundgrubesystem gegeben werden, und sie müssen von den Feldmaße ergelangt werden .

Jan 1, 2003

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

1. New books Specialty steels and hard materials, edited by N. R. Comins and J. B. Clark. Oxford, Pergamon, 1983.482 pp. Hardcover £55.50. Papers presented at an international conference on advances in flow measurement techniques, edited by H. S. Stephens and B. Jarvis. BHRA Fluid Engineering (Cranfield, Bedford, MK43 OAJ, England), 1982. £36. Papers presented at Fourth European Conference on Mixing, edited by H. S. Stephens and D. Goodes. BHRA Fluid Engineering (Cranfield, Bedford, MK43 OAJ, England), 1982. £36. Papers presented at an international conference on hydrocyclones, edited by H. S. Stephens and G. Priestley. BHRA Fluid Engineering (Cranfield, Bedford, MK43, OAJ, England), 1982. 248 pp. £27. Controlled atmospheres for heat treatment, by R. Nemenyi. Oxford, Pergamon, 1983. 225 pp. Hardcover 20, flexicover £7.50. Electrochemical techniques in corrosion testing and research, edited by J. S. Scully. Oxford, Pergamon, 1983. 150 pp. Flexicover £9.45 2. Book reviews Off highway truck haulage, by the Newman Combined Group. Parkvine (Victoria), Australasian Institute of Mining and Metanurgy, 1982. Reviewer: B. J. Vorster Elsevier's mineral and rock table, compiled by P. Lof. Reviewer: A. Wedepohl Field geologists' manual, by B. A. Berkman. Monograph Series No. 9, Australasian Institute of Mining and Metanurgy, 1982.295 pp. Reviewer: R. A. G. Cuipers 3. Mintek reports Report M56 A computer programme for the evaluation of process routes in the production of ferrochromium. Report M61 An atomic-absorption programme for the Apple 11 Plus computer. Report M63 A general-purpose data logger. Report M65 A preliminary survey of the corrosivity of water in gold mines. Report M66 A review of corrosion inhibitors: theory and practice. Report M67 The determination of total cyanide in solutions containing uranium and gold. Report M68 The suitability of Doppler flowmeters for use in the minerals-processing industry. Report M70 The preparation and certification of two reference materials of South African manganese ore. Report M78 A n evaluation of the Leeds laboratory-scale flotation cell. Report M79 The determination, by X-ray-fluorescence spectrometry, of gold and uranium on resin. Report M80 The installation and commissioning of a Siemens SRS200 sequential X-ray-fluorescence spectrometer. Report M81 The application of the inductively coupled plasma system to the simultaneous determination of precious metals. Open-pit and strip mines The South African Institute of Mining and Metallurgy and the Mining Alumni Society of the University of Pretoria are organizing an International Conference on The Planning and Operation of Open Pit and Strip Mines in Pretoria from 9th to 13th April, 1984. Other Institutes co-sponsoring the Conference are The Canadian Institute of Mining and Metallurgy, The Institution of Mining and Metallurgy, and The Society of Mining Engineers of AIME.

Jan 1, 1983

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

1. Reviews Steel and its heat treatment, by K-E Thelning. 2nd Edition. London, Buterworths, 1984.678 pp. R201,60 (incl. OS1). Reviewer: J.P. Hofman The Southern Queensland Conference 1985. Parkvile (Australia), The Australasian Institute of Mining and Metallurgy, 1986. A$ 15.00. Reviewer: R.B. McGilivray Rock mechanics, by A.R. Jumikis. 2nd edition. Clausthal-Zelerfeld (West Germany), Trans Tech Publications, 1983. US$ 58. Reviewer: R.W.O. Kersten The XVIth International Coloquium on Refractories. Freiburg, West Germany, 1985. DM 80. Reviewer: H.J. S. Kriek Diamond driling handbook, byW.F. Heinz. Johannesburg, South African Driling Association, 1985. 517 pp. R30. Reviewer: S.A.G. Martins Processing and utilization of high sulfur coals, edited by Y.A. Atia. Amsterdam, Elsevier, 1985.788 pp. Oft. 385. Reviewer: L.M. Falcon Weighingand proportioning of bulk solids, by Hendrik Colijn. 2nd edition. Rockport (U.S.A.), Trans Tech Publications, 1983. 398 pp. $60.00. Reviewer: G. Cunningham Investment appraisal and economic evaluation of mining enterprise, by S. von Wahl. Clausthal-Zelerfield (West Germany), Trans Tech Publications, 1986. US$ 40. Flotation of sulphide minerals, edited by K.S. Eric Forssberg. NewYork, Elsevier Science Publishers, 1985. 480 pp. US$1O1.75. Reviewer: T.R. Twidle 5th Meeting of the European Clay Groups (5th Euroc/ay Meeting), Prague, edited by J. Konta. Praha (Prague), Univerzita Karlova, 1985. Reviewer: D. Bibmann 2. Recent publications CSIRO. Research review1982-84: CS/Ra Division of Mineral Engineering. Melbourne, Commonwealth Scientific and Industrial Research Organization, 1985. 77 pp. The world copper market: structure and econometric model, by Gerhard Wagenhals. Berlin, Springer- Verlag, 1984. 202 pp. DM 37,00.Materials data of high-strength aluminium aloysfor durability evaluation of structures, edited by L. Schwarmann. Disseldorf (West Germany), Aluminium- Verlag GmbH, 1985. BRITISH GEOLOGICAL SURVEY. UnitedKingdom mineral statistics 1985, compiled by H.c. Squirel, A. Jones, N.E. Sharp, M. Lowe, and D. Slater. Keyworth (U.K.), the Survey, 1986. 175 pp.3. Mintek reports Report Ml66D The effect of calcining on the recovery of gold in a sand residue. (1st issued Sep. 1984.) Report M168D The treatment of Uitkomst concentrate. (1st issued Oct. 1984; reissued Mar. 1986.) Report M175D Supergene alteration at the Pering zinc-lead deposit: The nature and extent of the oxidation zone. (1st issued Oct. 1984.) Report M176D Bench-scale tests on the extraction of cobalt and nickel from COMAT leach liquors. (1st issued Nov. 1984; reissued Mar. 1986.)Report M241 PLA TO at Mintek. Report M243 The performance and wear characteristics of grinding media as affected by metallurgical and dimensional factors. Project development The Second Project Development Symposium on Planning, Construction and Commissioning will be held in Sydney, Australia, from 7th to 10th October, 1986. Hosted by the Sydney Branch of The Australasian Institute

Jan 1, 1986

1. Book reviews Mill Operators' Conference. Parkville (Australia), Australasian Institute of Mining and Metallurgy, 1982. 425 pp. Reviewer: B. K. Loveday Off highway truck haulage. Newman Combined Group, the Australian Institute of Mining and Metallurgy and the Institute of Engineers in Australia. Sep. 1982. Reviewer: B. J. Vorster Environmental engineering in South African mines.Johannesburg, Mine Ventilation Society of South Africa, 1982. 974 pp. Reviewer: A. N. Brown Underground Operators Conference. West Coast Tasmania Branch. Australasian Institute of Mining and Metallurgy. Reviewer: D. R. Aspeling 2. New publications Electric steelimaking in the eighties: challenges and opportunities. Rotterdam, Balkema, 1982. 362 pp. $50.00 or £33. Tungsten: a review, by P. M. Harris and D. S. C. Humphreys. London, Institution of Mining and Metallurgy (Occasional Paper 2), 1983. Members: £3, nonmembers £6. The platinum industry - prospects in recovery. London, Shearson{American Express Ltd (St. Alphage House, Fore Street, London EC2Y 5DA), 1983. £75. The best of E&MJ mining and processing idea book' New York, Engineering and Mining Journal, 1983. 128 pp. Free with subscription to Engineering and Mining Journal. Mining 1983. Harlow (U.K.), Longman Group Limited, 1983. 500 pp. £39.50. Ooncise guide to world coalfields. London, World Coal Resources and Reserves Data Bank Service (14/15 Lower Grosvenor Place, London SW1W OEX), 1983. 380 pp. £45. 3. Canadian publications Asbestos, by G. O. Vagt, 9 pp. Ooal and Coke, by J. A. Aylsworth, 16 pp. Orude oil and natural gas, by R. L. Thomas, 12 pp. Phosphate, by G. S. Barry, 8 pp. Rhenium, by S. A. Hamilton, 3 pp. 4. Mintek reports Report 2102D The recovery of magnesite from dump fines from the Strathmore Mine. (First issued Feb. 1981.) Report 2106D The evaluation of drill cores and a bulk sample from a deposit of andalusite near Thabazimbi. (First issued Mar., 1981.) Report 2108D Evaluation of a grinding aid in batch grinding, classification, and gravity concentration. (First issued Jul. 1981.) Report 2109D The evaluation of an andalusite deposit from Kleinfontein, Groot Marico. (First issued Apr. 1981.) Report M7D The beneficiation of chromite ore from the Ma-l seam near Marikana. (First issued Nov. 1981.) Report M62 A preliminary investigation into the extraction of zinc by direct oxidative leaching of high-manganese sphalerite. Report M76 A mineralogical investigation of a refractory gold ore, and of a sulphide concentrate and calcined tailing from that ore. Report M85 List of unrestricted Mintek publications issued from 1966 to 1982. Report M97 Reduction in metal consumption by the use of alternating lines of higher and lower lifter bars in a rod mill. Report M98 Multivariable control and optimization of the operation of a milling circuit at East Driefontein Gold Mine. Report M101 The potentiality of heat-treated balls in the grinding of gold ores. X-ray diffraction The Southern Transvaal Section of the South Mrican Chemical Institute is to present a mini-course on 'X-ray Diffraction: Theory and Application' in Johannesburg on 18th and 19th October, 1983.

Jan 1, 1983

COUNCIL The following served on Council during the year under review Office Bearers Dr J. P. Hugo (President), P. W. J. van Rensburg and Professor R. P. Plewman (Vice-Presidents), Professor D. D. Howat (Immediate Past-President), and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council H. P. Carlisle (until February), R. C. Espley-Jones, G. H. Grange, Dr D. I. Legge, W. W. Malan, J. B. Mudd, Dr R. E. Robinson, Dr M. D. G. Salamon, L. W. P. van den Bosch, D. A. Viljoen (co-opted May 1973), and P. A. von Wielligh. Branch Chairmen A. Bain (Witbank-Middelburg Branch), C. J. Isaac (O.F.S. Branch). Past Presidents Serving on Council R. J. Adamson, M. Barcza, H. Britten, J. K. E. Douglas, R. C. J. Goode, P. Lambooy, Professor J. de V. Lambrechts, Dr J. T. McIntyre, J. F. Reid, and V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 18, and the standing committees held 29 meetings. MEMBERSHIP Twelve Fellows, ten Members, twenty-one Graduates, eleven Associates, thirty-one Students, and forty-two Company Affiliates were elected during the year. One Member was reinstated. Eight Fellows, two Members, and two Associates were admitted to retired membership. Four Graduates were transferred to Members, one Associate to Member, three Students to Members, one Graduate to Associate, two Students to Graduates, and one Student to Associate. Your Council records with deep regret the death during the year of the following : D. R. Campbell, J. Daniel, M. J. Dennehy, and F. S. C. Rogers (Life Fellows) ; W. T. balling and T. Pryor (Life Members); C. Boocock, W. Drake R. J. Moore, M. P. Pearse, J. M Pike, W. A. Schwezoff, A. I. Suss man, and L. G. S. Wright (Fellows) ; A. F. Chalmers (Member) ; and W. R. Gerry and G. T. Rimmer(Associates). A comparative statement of membership as at 30th June, 1973, and the end of the previous year it shown in the following tabulation: 30th - 30th June, - June, 1972 - 1973 Honorary Life Fellows 5 - 4 Honorary Fellows 13 - 9 Life Fellows 181 - 177 Fellows 541 - 536 Members 479 - 487 Graduates 115 - 128 Associates 182 - 186 Students 162 - 183 Company Affiliates 24 - 64 1 702 - 1 774 JOURNAL The papers that were published in the Journal during the year are listed below: August, 1972 The effects of chromium oxide, iron oxide, and calcium oxide on the liquidus temperatures, viscosities, and electrical conductivities of slags in the system MgO-Al2O3-SiO2, by M. S. Rennie, D. D. Howat, and P. R. Jochens A study of the dust exposure of South African white gold miners, by R. J. Page-Shipp and Elizabeth Harris A forecast of the coal and uranium requirements for electric power generation in South Africa, by E. J. Maunders September, 1972 Mine management by objectives, by A. A. Hazell Some aspects of the deformation behaviour and temperature rise during instantaneous compression loading of high purity aluminium, by H. J. E. Hamel Computer control of flotation at the Ecstall concentrator, by M. P. Amsden, C. Chapman, and M. G. Reading Optimizing the public gains from the exploitation of mineral resources, by A. Azis and J. Zwartendyk October, 1972 Presidential Address: Nuclear energy: its interactions with mining and metallurgy, by J. P. Hugo Presidentsrede: Kernenergie: sy wissel-werkinge met mynbou en metallurgic, deur J. P. Hugo Raise-boring experiences in the gold mines of the Anglo American Corporation Group, by J. W. Wilson and P. C. Graham November, 1972 Materials for winding plant components, by G. T. van Rooyen An analytical solution to the batch-comminution equation, by R. P. King A new approach to the study of human factors in stope productivity, by A. C. Lawrence Fundamental studies of the flotation process: the work of the National Institute for Metallurgy, by N. P. Finkelstein and V. M. Lovell Growing use of deionised water in surface coating techniques, by W. F. Lorch December, 1972 The development and application of a computer system to aid in the planning of production in mines, by F. H. Deist, L. F. Duvel, J. D. Austin, and H. D. Small PERT, and how PERT techniques can be used in modern mine management, by E. J. Boome and A. C. Schmidt A critical comparison of specific cooling power and the wet kata thermometer in hot mining environments, by J. de V. Lambrechts January, 1973 Liquidus temperatures in the Cr-Fe-Si system in the composition range representative of ferrochromium-silicide produced in South Africa, by J. C. M. Wethmar, D. D. Howat, P. R. Jochens, and O. A. W. Strydom Platinoids in the Witwatersrand System, by C. A. Cousins The development of a continuous recording scintillation counter mounted on a cyclometer, by P. D. Teens and D. Visser February, 1973 Computer analysis, modelling, and optimisation of gold recovery plants of the Anglo American Group, by M. I. Brittan and E. J. J. van Vuuren The significance of the mineralogical and surface characteristics of gold grains in the recovery process, by C. E. Feather and G. M. Keen Statistical valuation of diamondiferous deposits, by H. S. Sichel March, 1973 The effect of the reactivity of lime on desulphurisation efficiency in the basic oxygen furnace, by A. A. Hejja, D. D. Howat, and P. R. Jochens A review of real-time particle size analysers, by A. L. Hinde In situ measurements of the surface heat transfer coefficient in underground airways, by K. R. Vest April, 1973 An investigation into the kinetics and mechanisms of the oxidation of iron (II) by oxygen in aqueous chloride solutions, by R. P. Colborn and M. J. Nicol Electric smelting at Rustenburg Platinum Mines Limited of nickel-copper concentrates containing platinum-group metals, by J. C. Mostert and P. N. Roberts Metallurgical considerations in the

Jan 10, 1973

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

Discussion H. J. S. Kriek*: During 1956 Iscor became interested in the acid smelting in a blast furnace of siliceous ores containing 15 per cent silica. This interest was as a result of the successful acid smelting in Germany at a CaO/SiO2-ratio of between 0.4 and 0.8. Acid smelting can become an economic proposition due to a reduction in slag volume accompanied by a lowering of the coke rate. Paschke and Hannel1 found that a free flowing slag (i.e. viscosities of less than two poise) would not be obtained at C/S-ratios lower than 0.82 and that the addition of 3 to 4 per cent alkalies became necessary. In titanium bearing slags it was established that maximum fluidity is obtained with 10 per cent TiO2. Acid smelting resulted in increased sulphur pickup with decreasing O/S-ratio and desulphurization with soda-ash outside the blast furnace was necessary. At Iscor Mr B. B. Segal established that, for slags with (CaO+MgO)/SiO2-ratios of 0.5, 0.6 and 0.7, the addition of alkalies and TiO2 resulted in a substantial decrease in melting point and also of viscosity. At a (CaO+ MgO)/ ratio of 0.53 the addition of 10 per cent TiO2 is as effective as the addition of 3.75 per cent alkalies. This means that a blast furnace can be run without the addition of alkalies and consequently the detrimental effect of alkalies on the lining can be avoided; also that fluid slags with 5 to 15 per cent MgO and 8 to 10 per cent Al203 can be obtained with 10 per cent TiO present. (CaO+ MgO)/SiO2-ratios smaller than 0.5 the addition of titania resulted in a decrease in melting point and also in an increase in viscosity. In ceramic crucibles the slag did not become more viscous with time but thickened appreciably when held in graphite crucibles. No titanium carbonitride could be detected and only Ti20a was found. Prof Howat also did not obtain the TiC-TiN solid solution and therefore it appears that the thickening of the slag is not solely due to the formation of the titanium carbonitrides. This is in agreement with the work of Michailov and Belyakova2 who found that TiO2 decreased the viscosity of acid slags and increased the viscosity of basic slags; that titanium sesquioxide (Ti203) and titanium monoxide (TiO) increased the viscosity of both acid and basic slags and that titanium carbide, which is found in larger amounts in basic slags than in acid slags, considerably increases the viscosity of both acid and basic slags. Patzak et al3 describes the following oxygen deficient titanias, viz Ti2O, TiO, Ti203, Ti3O5, Ti4O7, Ti5O9, Ti6O11- Ti10O9,Ti7O13,Ti8O15 and Ti9O17. Until about 1959 a fair amount of data was available on the viscosity of normal slags to which titania was added2, 4, 5, 6, 7, 8, 9. At Iscor an electromagnetic viscometer based on the viscometer developed by Bockris10 was built. Progress was very slow as our main attention was centred around problems associated with the operation of the Rotor process. During 1962 and 1963 two papers containing fundamental work on the viscosities of slags in the systems CaO-SiO2-TiO211 and CaO-SiO2-TiO2 at 0 per cent A1203, 10 per cent Al203 and 20 per cent Al20312 appeared. The work of Ross and Ohno obviated the necessity of any further work by Iscor on the viscosity of blast furnace slags containing titania. Ross gave the following optimum compositions for blast furnace slags containing titania. Titania % Lime % Silica % Lime/Silica-ratio 20 30-42 38-50 0.6-1.10 30 27-36 34-43 0.63-1.06 40 24-32 28-36 0.66-1.14 The optimum temperature is 1,500°C because at this temperature the largest workable composition range exists. Higher temperatures result in narrower optimum composition ranges and in increased rates of thickening. The factors affecting the rate of thickening were also investigated by Ross and Ohno, as the main problem with slags containing titania is not finding compositions which are fluid at operating temperatures but the thickening due to a lack of oxygen. With these slags when there is insufficient oxygen to co-ordinate each silicon atom with its own individual shell of four oxygen ions, some sharing of oxygen ions must occur, resulting in the formation of large silicate ions and a rise in viscosity. The formation of oxygen deficient titania can be prevented as long as iron oxide or manganese oxide remain in the liquid slag. Iwase13 and also Viens, Camp bell and Rogers14 obtained in the experimental smelting of ilmenite ores fluid slags with more than 3 to 5 per cent manganese oxide and ferrous oxide in the slags. It appears that titaniferous ores can be smelted in blast furnaces under the following conditions: (1) Acid slag operation, i.e. at C/S-ratios from O.6-1.0. (2) Dolomite can be used as a flux as MgO is a network modifier. (3) The Al2O3-content must be less than 15 per cent as alumina promotes thickening of the slag and decreases the optimum composition range. (4) The hearth temperature must not exceed 1,500°C. According to Ross a definite amount of energy is required for each ton of iron produced and in order to increase production an increase in heat

Jan 6, 1969

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

By T. Mützea, L. Schützenmeister, G. Kacheb

High-Pressure Grinding Rolls (HPGR) are employed in cement plants worldwide. Although the technology has been mastered in the majority of applications, design-, scale-up- and operationalchallenges still exist today. In addition to modelling throughput, energy requirement and comminution success, the prediction and avoidance of malfunctions is of great importance in current research. The performance of the mill is highly influenced by the roll speed and the fineness of the feed material. Another parameter influencing the composition of mill feed is the circulating load, which is determined by the grinding circuit configuration, the target fineness and the separation efficiency of the classifier. In order to meet this circumstance and simultaneously maintain a reasonable level of material input and testing effort, a complete grinding circuit on a small technical scale was set up in the research centre of Thyssenkrupp Industrial Solutions AG. The present study varied the roll speed (0.5-2 m/s) and the proportion of fines in the feed (0-75 %) in order to investigate the influence of both parameters on the finish grinding of a Portland cement with a target fineness of 4000 cm²/g according to Blain. The experimental results are compared with model concepts and critically examined with regard to their transferability to industrial plants. Keywords: Cement grinding, grinding circuit, HPGR

Jan 1, 2020

By H. W. Glen

The National Institute for Metallurgy - usually referred to as NIM - has become the Council for Mineral Technology, or Mintek. The Honourable F. W. de Klerk, Minister of Mineral and Energy Affairs, announced the change of name at the official opening of the main entrance to Mintek's premises on 30th October, 1981. Awards for bravery Two men who disregarded the dangers of fiercely burning timber and falling rocks to douse an underground fire, using their hard hats to scoop water from a drain, received the Chamber of Mines Award for bravery at a ceremony held at West Driefontein Gold Mine near the end of October.

Jan 1, 1981

By P. J. Lloyd

Society is fully justified in its concern about the environment, but that concern may, at present, be too uncritical It is, for instance, essential to establish that there is a valid environmental impact, and that there is truly a causal link between a human activity and an observed shift in environmental conditions. In establishing these, it inessential to recognize that scientific proof offers consistency, but that it can never provide completeness. Thus, no amount of scientific endeavour can ever prove that mitigation of the effects of human activity will be perfect. Society normally expresses its concern through legislation. The existing legislation in South Africa is reviewed, and it is found that [>legislation regarding water is probably too stringent to be effective, >legislation regarding air and land use is probably too lax, >all the environmental legislation is too fragmented to be efficient, and the Department of Environmental Affairs is hamstrung by inter-departmental rivalry. ] It is accordingly concluded that, if means are to be found for ensuring adequate mitigation of environmental impact in the face of ongoing economic development, it is necessary to establish a Judicial Commission on Environmental Affairs advised by, but given greater powers than, the departments currently active in environmental maters. This Commission should be charged with creating, perhaps over a decade, a body of legislation that would guide development while protecting the environment in its widest sense.

Jan 1, 1994

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By A. V. Z. Brink

This paper describes the development of a monitoring architecture that allows for continuous monitoring of the process of mining, the underground environment, the state of the rockmass and its response to mining. The system is based on an open standard and is non-propriety. It allows for dense sensor arrays in the workplace, wire less communication to the closest power line, and TCP/IP communication to a central server. Continuous monitoring and quantification of the appropriate parameters allows a mine to optimise its mine process; to dynamically access the safety and health risk to people and equipment; and to quantify exposure to potential heath hazards such as dust, gas or noise. Current application examples of continuous monitoring include an application to optimise drilling and blasting thought fragmentation monitoring; an application of wireless sensor network-based monitoring in to provide early detection of potential rockfalls; and a trail to continuously assess the gold grade at the shaft through correlation with radioactivity. It is unlikely that a single monitored parameter will provide adequate knowledge of the assessed risk or even an optimisation approach. Multiple parameters are being combined using cognitive science tools such as Bayesian theory and other statistical methods to improve the accuracy and relevance of, for example, risk quantification. The decision maker is not confronted with massive amounts of raw data but rather with a single knowledge statement such a probability of failure, a human physiological strain index or an optimisation index.

Jan 1, 2008

By J. F. Morrison, C. H. Wyndham, N. B. Strydom

INTRODUCTION The shovelling of rock in stopes is still a basic and important operation in many gold mines in the removal of gold-bearing rock from the stopes. There is, however, little factual knowledge of the factors which influence the the rates of energy expenditure and work output, and of the way in which variations in these factors, individually or in combination, affect the mechanical efficiency of the mine workers. What for example is the influence of different rates of shovelling, shovel loads and distances of throw? How does stope width and dip of the stope affect the mechanical efficiency of men shovelling rock? Recently a simple physiological test was introduced into the gold mining industry for classifying Bantu recruits into those capable of hard, moderate and light work. If this test is used to select only those Bantu mine workers who are capable of hard work for the task of shovelling rock in stopes then the rate of energy expenditure which could be expected from these men is 1.5 litres/min for the entire period of the shift. With an adequate knowledge of the influence of the various factors which affect the rate of energy expenditure of men shovelling rock in stopes it would be possible to set work standards for Bantu mine workers in stopes. This should be done in terms of the rate of shovelling, the shovel load and the distance of throw for any combination of width of stope, dip of stope, condition of foot wall and grade of rock in such a way that the resultant energy expenditure would be the 'optimum' that could be expected from the men but would be within their capacities for physical work of an endurance nature (that is, 1. 5 litres/min from the 'average' Bantu mine worker). Work standards could thereby be determined for the different stopes of a mine on a sound and systematic basis. In order to supply the information required a study was carried out by the Human Sciences Laboratory in which the work output and energy expenditures (in terms of oxygen consumption in litres/min) were measured on six highly trained Bantu mine workers under the following conditions: (a) rates of shovelling of 3, 4, 5, 6, and 10 shovels per minute. (b) loads of from 9 to 18 lb on the shovel. (c) distances of throw from 8 to 20 ft. (d) stope width of 28 in., 42 in. and 72 in. (e) dip of stopes of 0°, 15° and 30°. (f) rough and smooth footwalls and various grades of rock size. This paper gives the main results of practical importance of this study. Method The experiments were designed and conducted in conjunction with the Work Study Department of one certain underground conditions such as variable stope widths, stope angle, etc., were made available in a mine Surface Training School and suitable subjects were selected from the large number of labourers being put through the training school. Subjects Bantu recruits who had returned to the mine for a new contract and who had previous underground experience on shovelling were considered to be suitable as subjects for the experiments. The particulars of the subjects are given in Table I. TABLE I PHYSICAL CHARACTERISTICS OF SUBJECTS Weight Height Surface area Max O2 capacity Subject (Kg) (cm) (sq meters) (Litre/minute) A 71.5 167.3 1.80 3.5 B 61.5 162.3 1.65 2.8 C 63.0 164.1 1.69 2.4 D 66.5 167.4 1.75 2.8 E 70.2 164.6 1.77 3.0 F 77.8 173.1 1.92 3.8 Training The method of shovelling, accepted by the Work Study Department, was demonstrated to the subjects who then practised the movements with empty shovels, under the supervision of an instructor. After the technique was mastered, the men started shovelling rock and were trained for at least four hours per day to work at the higher shovelling rates. Training was continued for three weeks to enable the subjects to achieve a reasonable degree of physical training and conditioning. Shovelling method In both the kneeling and standing positions the subjects faced the pile of rock, grasped the shovel in the accepted manner and pushed the blade of the shovel into the base of the pile of rock, sliding the blade between the rock and the concrete floor. In the standing position (72 in. wide stope) the back leg assisted in the movement by pushing the knee against the back of the hand holding the shovel handle. In the kneeling position the elbow was tucked into the side of the body so that the muscles of

Ninth International Symposium TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of 14th to 19th June, 1970, follows the Computer Symposium held in Salt Lake City in September, 1969. The purpose of the Symposium is to define the role of decision-making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-have permitted us to structure it in such a way that a complete picture of the mineral industry in its public policy, corporate, financial and technological environment emerges. Topics for the sessions are: . The Public Policy Environment;. The role of Decision Making Techniques in the Mining Company; . Information Storage and Retrieval; . Markets-Forecasting, Patterns and Strategies;. Search for Mineral Deposits;. Quantification of Geological Variables;. The Mine Development Decision; Production Systems;. Planning, Scheduling and Control Systems. The sessions will be directed energetically by chairmen who have been in continuous contact with the authors, providing them with information about related papers and sessions. This symposium is sponsored by the Canadian Institute of Mining and Metallurgy, McGill University and Ecole Polytechnique. Further information may be obtained from: The 9th International Symposium. W. H. Gauvin, General Chairman, J. Elbrond, Programme Chairman. Department of Mining Engineering, Ecole Poly technique, P.O. Box 501, Snowdon, Montreal 248, Quebec, Canada. ACHEMA 1970 The European meeting of Chemical Engineering and the Achema Congress 1970 is being held at Frankfurt/Maine, from 17th to 24th June, 1970. The programme includes some 110 plenary and specialised lectures, numerous technical films, excursions, and technical discussions in front of the exhibits which form the central feature of the Achema-Exhibition Congress. Further information may be obtained from the honorary representative of Achema in South Africa, Mr F. Schilling, P.O. Box 31274, Braamfontein, Johannesburg. NINTH COMMONWEALTH CONGRESS PROCEEDINGS Publication of the proceedings of the Ninth Commonwealth Mining and Metallurgical Congress, 1969, is being undertaken by the Institution of Mining and Metallurgy, London. There will be four volumes covering papers presented at the Congress together with the discussion and author's replies, and the addresses by Sir Duncan and Sir Ronald Prain. These will be available April-June 1970. Special pre-publication prices apply to orders received before 1st April, 1970. Order forms may be obtained from Secretary S.A.I.M.M., P.O. Box 1183, Johannesburg. 6th World Congress on the Prevention of Occupational Risks This Congress, dealing with industrial accidents and occupational diseases, will be held in Vienna from 10th to 15th May, 1971. Further information may be obtained from: VI Weltkongress für Unfallverhütung, Postfach 745, A-1015 Wien, ÖSTERREICH. International Vacuum Metallurgy Conference 1970 The Vacuum Metallurgy Division of the American Vacuum Society is organizing an international meeting that will be held at the Convention Center in Aanaheim, California from 15th to 19th June, 1970. Enquiries should be directed to the Arrangement's Chairman, L. M. Bianchi, TRW Inc., 23555 Euclid Avenue, Cleveland, Ohio 44117, Tel. No. (216) 383-2111. AIME WORLD LEAD-ZINC SYMPOSIUM This symposium is being held from 21st to 23rd October, 1970, in St. Louis, Missouri, U.S.A., in conjunction with the Fall Meeting of the Society of Mining Engineers, and a Rapid Excavation Conference. In addition to local field trips to smelter and refinery operations there will be a number of extended trips of six to eight days. Information may be obtained from: Mr. John C. Fox, Secretary, Society of Mining Engineers of AI.M.E., 354 East 47th Street, New York, N.Y. 10017, U.S.A. NEW SUBSCRIPTION RATE TO THE JOURNAL As from 1st JANUARY, 1970, the subscription rate for the Journal has been increased from R12.00 to R18.00 per annum, i.e. R1.50 per issue instead of R1.00. The discount to booksellers is 15 per cent. COURSEOF THE THEORYOF THE UNIT OPERATION OF GRINDING The South African Institute of Chemical Engineers is arranging for Prof. L. G. Austen to conduct a course on the above subject in September, 1970. Interested persons should contact Dr G. S. Harrison, S.A. Institution of Chemical Engineers, A.E. & C.I., 15 Anderson Street, Johannesburg. METRICATION The S.A. Bureau of Standards has published a document entitled "Metric Scales and Units for use in the Building and Construction Industry." It has been compiled by the Metrication Committee of the National Building and Construction Advisory Council and is the first of the series of informatory documents relating to the programme for the metrication of the Building Act Construction Industry. This document is obtainable from the South African Bureau of Standards, Private Bag 191, Pretoria at 50c per copy.

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By R. R. M. Cousens, W. S. Garrett

Discussion: L. T. Campbell Pitt: When Mr Garrett and I discussed the design and construction of plugs and bulk head doors to resist great water pressures in mines about ten years ago, we visualized an emeregeny when there would be no time for site preparation. We could not however, anticipate a problem of such magnitude and urgency as the one described in the paper under discussion. The paper very clearly describes the flooding and the measures taken to save the mine. The complete flooding would have been a national disaster. The account of the combat between man and water reads like the account of a military operation. It was an endeavour which achieved success because there was a master plan, tenacity and, in fact, heroism. The paper is of necessity a long one. In my contribution I will mention some historical facts and factors that I believe have relevance to the flooding and the saving of the mine. It is of great satisfaction to me to have been one of the two initiators of a new approach to underground plug design and construction. The investigation was taken over by a Chamber of Mines Committee which combined our early work with further research and the resulting data had a significant bearing on the West Drie emergency plug designs. The final plug length was correctly based on the requirements to obviate leakage. A plug to have structural strength only would have been very much shorter but so ineffective as to have become a waste of labour, material, and in consequence, wasted the limited time available to prevent flooding of the whole mine. The figure of 75 lb per sq in. sheer stress provided a very ample margin, in my opinion, but under the very difficult site conditions and the limitations of plug material suitable for the very unusual construction, justified such a figure. There must have been considerable temptation to reduce the safety margin due to the urgency to complete and commission the plugs, but it is much to the credit of the directors of this operation that nothing less than a safe design was permitted. In about 1945 Blyvooruitzicht Gold Mining Company, which was then mining in to the West Driefontein area to assist in early development, decided to protect themselves from a possible inrush of water from the latter mine. A bulk head door was accordingly designed and installed on 2 level between 1945 and 1948 at 4,218 ft below surface. Since West Driefontein paid for it, Gold Fields consulting mechanical engineers collaborated with their colleagues of Rand Mines who completed their design after a few modifications were agreed. This door was never used to prevent an inrush into Blyvooruitzicht but the exercise was very useful to Gold Fields when the high pressure doors initially installed on 10 and 12 levels between Nos. 2 and 3 shafts to enable isolation of one section of the mine from another were designed. At that time the capacity of West Driefontein to cope with an inrush of water was comparatively small because the storage in stoped areas and the installed pump capacity were much less than in later years. These doors together with others of the same design were later moved to the lower levels served by sub vertical shafts. In addition, doors to prevent flood water entering the pump chambers on 18 level were installed at each end of that level, and designed for a head of 360 feet so that water would have to reach 16 level before the pumps were flooded. All these doors were called upon to hold water and it is reported that only a small plug in one of the doors and a 4 in. dia flanged pipe joint failed. The lesson is that in these cases the smallest details warrant as much attention as the major ones. That these were the only equipment failures when so much depended on equipment, is very much to the credit of design engineers, both of the Gold Fields head office and companies who supplied both mechanical and electrical equipment. Until I had read the paper I wondered why the policy of isolation by bulk head doors was not continued as the development moved eastward towards the Bank Compartment and particularly when it pierced the Bank dyke. The reasons have been given in the paper. It was unreasonable to expect provisions to be made to counter the remote contingency that the large installed pumping capacity and mine capacity to store water would be exceeded during a peak inrush. When pumps were being considered for West Driefontein, it was decided that the Gold Fields standard underground main pumps at that time of 1 million gallons per 24 hours would be too small. Three alternatives were considered. 1. Very large units that would require underground sub assembly and dismantling of both pump and motor. 2. The largest pump and motor that could be conveyed as a complete pump or motor from surface to the pump chamber. 3. Pumps of higher speed to reduce dimensions and weight. It was decided to adopt alternate 2 because of avoidance of transporting pumps in parts and assembling underground. Alternative 3 was not favoured because high speeds would have introduced problems of more exact rotor balancing. I believe the decision was correct and in the crisis enabled comparative easy transport of pumps and motors to surface for overhaul and, if required, transfer to other pump stations. The standard pump thus became a 10 stage 1,500 rpm pump with a capacity of approximately 2 million gallons per 24 hours against a static head that varied

Jan 3, 1969