Search Documents

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

By D. M. C. Valbom

The introduction of new diamond sorting technologies as well as additional manufacturers I vendors, has increased the equipment selection and combinations available for recovery flowsheet design. This paper describes the methodology used and the benefits realized in the design of recovery plants by ensuring a fundamental understanding of the advantages and limitations of the technology embodied in the equipment, a comprehensive knowledge of the ore body characteristics, and the effective matching of this information in combination with operational commercial requirements.

Jan 1, 2010

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By R. Kus´

The paper presents the comments on the advantages of implementing an integrated system of managing mining exploitation in hard coal mines, as well as the comprehensive integration of information on the process of deposit exploitation with economic data, so as to achieve an optimum technical and economic effects. The principles of constructing the production management system have been presented, thanks to which the management boards are provided with reliable technical and economic information on a mining company via information technology. The strategic direction of a company’s operation may currently be verified according to the external conditions that change over time (the information on the deposit, force majeure events, changing expectations of customers, etc.).

Jan 1, 2003

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By S. Burks

This paper develops the themes explained at the previous SAIMM Platinum conference by Whittle and Burks1. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long- term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: ? An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated ? An existing operation with an integrated portfolio of mines, concentrators, smelter and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets ? An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated ? An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the Owner?s team.

Jan 1, 2012

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

By R. J. Jewell

The storage capacity of any given tailings storage facility (TSF) is a function of the volume available for the tailings, for which the geometry of the final upper surface of the tailings is most important. One of the advantages that can be obtained from thickening tailings prior to discharge is that the tailings can be stacked at a steeper beach angle than is obtainable with conventional low-density slurries. However, there is at present no universally accepted method available for the accurate prediction of tailings beach slopes. This paper examines the current situation with the objective of putting the quest for a method for the accurate prediction of beach slopes into perspective. The paper references published reviews of the best-known beach slope prediction methods. However, there do not appear to be any independently verified projects or published references to projects on which a Class A prediction has been validated for any of these approaches, and in those instances where projects have been implemented correlation of actual with predicted slopes has been poor - often due to differences between the properties of the tailings assumed in the design and those actually achieved in the field. The author also concludes that flume-scale testing cannot be taken as a reliable indicator of full-scale performance, and suggests that the outcome of any current predictive method should be used by experienced practitioners as only one of a range of indicators in order to suggest a range of slope angles likely to result for any given operation. Practice has shown that it is possible to manipulate beach slopes by changes to the disposal technique, such as limiting the rate of discharge per discharge point and by increasing or decreasing yield stress, but the impact of these changes cannot readily be predicted. There are also newly emerging technologies, such as the injection of a polymer into the tailings at discharge, that will enhance the dewatering of tailings and hence expedite the consolidation of the tailings, that could well facilitate the development of steeper beach slopes. The overall conclusion is that with the current state of knowledge, the accurate prediction of beach slopes is not possible. Furthermore, in view of the inherent variability of the tailings parameters from any operation, it may well be of more value to concentrate on developing an understanding of the means by which the tailings parameters may be manipulated by the operators to achieve a given beach slope than to concentrate wholly on developing a generic beach slope prediction model.

Jan 1, 2012

By J. Engelbrecht

South Africa?s re-entry into the fast moving and competitive global economy calls for some careful strategic planning and a good deal of co-operation between suppliers and end-users. The issues that need addressing are generally well known and include: ?South Africa was ranked 45th out of 46 i.r.o. productivity ?SMMEs contribute 1% to exports compared to 40-60% for the ?tigers? ?High unemployment ?Limited skills of the majority of workers ?Slow growth rate of the economy ?The vast majority of suppliers are not world-class ?The vast majority of suppliers are not export or marketing orientated. In order to survive, all parties, i.e. government, labour and business, will have to play their part.

Jan 1, 1999

By R. M. Mashishi, T. Malehase, O. J. Okonkwo

The concentrations of selected trace elements (As, Cd, Hg, and Pb in run-of-mine (ROM) coal, discard, and coal product were investigated to assess the efficiency of beneficiation in reducing trace element concentrations and ascertain any implications regarding environmental compliance to regulatory frameworks. Samples were collected from a colliery in Mpumalanga Province twice a month for a period of 24 months. The samples were ashed to approximately 0.21 mm, then digested in a mixture of 70% HNO3 and 40% HF and analysed using inductively coupled plasma-mass spectrometry (ICP-MS). Except for Pb, the mean concentration of all elements decreased from the ROM stage to the coal product stage. The order in which trace elements occurred from the highest to lowest throughout the production chain was Pb>As>Hg>Cd. With the exception of Cd, the mean trace element concentrations in the discard were above the total concentration threshold (TCT) set for landfill disposal. The As, Hg, and Cd concentrations in the product were well below the thresholds for all land uses. However, Pb concentrations in the product coal were above legal limits, which is of concern with regard to environmental compliance and the performance and marketability of the product.

Dec 13, 2023

By T. Bhambhani, E. Arinaitwe

Solvay has developed several novel reagent innovations to improve separations in sulfide ore flotation and address major industry challenges. These innovations include: a) carbon management strategies to reduce the deleterious impact of organic carbon on flotation circuits; b) new collectors for heavily tarnished or oxidized Cu-Au ores; and c) a functionalized depressant for minimizing penalty elements in metal concentrates. Owing to their unique chemistries, these innovations exhibit a wide spectrum of rather unique properties that are quite in contrast to the traditionally used reagents. The chemistry, attributes, application, and advantages of these innovations are discussed in this paper based on laboratory, pilot, and plant results and observations for various ores

Jan 1, 2023

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

By R. G. Votteler, A. C. Brent

"The business performance of mining corporations in South Africa is adversely affected by the constantly increasing electricity costs. The most commonly used power sources are the national utility supplier via a grid connection, and on-site diesel generators. Previous research has identified the renewable sources of solar photovoltaic (PV), onshore wind, and geothermal energy in hybrid versions with current sources as possible opportunities to counteract rising electricity costs. To provide a clear understanding of the new, developing market of renewable energy sources, this research is divided into two papers. This first paper investigates the internal business structure of mining corporations in order to evaluate electricity generating sources. The multi-criteria decision analysis (MCDA) method is selected as the most suitable approach for this. The paper identifies the criteria used by mining corporations to evaluate possible electricity generation sources for self-generation by means of the corporations’ own investment. Four mining corporations with several mining locations were interviewed. The interviews revealed both new and identical evaluation criteria when the findings were compared to earlier MCDA adaptations analysed in the literature review. The second paper (Part 2) combines current knowledge about the external macroeconomic environment with the findings about the internal environment described here. MCDA is adapted in Part 2 and implemented to analyse and compare current to hybrid renewable sources from the perspective of mines. IntroductionMining corporations in South Africa are currently adversely affected by increasing electricity prices. Electricity is supplied mainly by Eskom1 and, especially in remote locations, by on-site diesel generators (Boyse et al., 2014). Electricity price increases, emanating from diesel price hikes and Eskom, have escalated the total operational expenditure on electricity by the largest mining corporations from 8% to 20% of total operating costs in the past seven years (EIUG, 2015). The reliability of electricity supplied by Eskom has decreased drastically (Govender, 2008), and the prices will increase annually by at least 13% until 2018 (Numbi et al., 2014; Eskom, 2015b). In addition, the South African government plans to introduce a carbon tax on greenhouse gas emissions (Alton et al., 2014)."

Jan 1, 2017

"This study examines the problems faced by open pit mine superintendents who make choices about how to direct their materials, either to the waste dump or to the mill. The paper explores the effects of introducing a 10% sampling error and a 0.9-times to 1.1-times sampling bias on positively skewed distributions for precious and base metals, negatively skewed distributions in the case of bulk commodities, and normal distributions as is the case for coal deposits. Parent distributions for each commodity were created on a 25 x 25 m grid using transformations of gold, iron ore, and coal data-sets, spatially based on a nonconditional Gaussian simulation. Ordinary kriging of grades for the three commodities into a 10 x 10 m grid provided the reference case against which the distributions with the sampling error and sampling bias for the commodities were compared. Imposing cut-off grades on the actual-versus-estimated scatterplots of the three commodities allowed the distributions to be classified into components of waste, dilution, ore, and lost ore. Ordinary kriging of values for each deposit type acted as the reference data-set against which the effects and influence of 10% sampling error and 0.9-times to 1.1-times sampling bias are measured in each deposit type. Indications are that the influence of error and bias is not as significant in gold deposits as it is in iron ore and coal deposits, where the introduction of small amounts of error and bias can severely affect the deposit value.IntroductionThe effects of poor sampling and the financial implications for mining companies, traders in mineral assets, and sellers of metal as dore or commodities is documented in a number of studies, the most notable of which is that by Carasco (2004). He examined the financial impact of poor sampling practices in the Chilean copper industry and found that finacial losses due to poor sampling amounted to hundreds of millions of dollars over the life of a mining operation. Holmes (2004) examined the effects of correct sampling and measurement as the foundations of metallurgical balances, and found that revenues from the sales of large iron ore shipments may be profoundly affected by poor sampling practices. In South Africa the way in which sampling of in situ gold-bearing reefs affects the mine call factor has been an ongoing study since the disparity between the estimation of gold in the reef and the actual gold bullion produced was noted by early investigators such as Beringer (1938), Jackson (1946), Sichel (1947), Harrison (1952), and a number of others."

Jan 1, 2017

By C. H. Wyndham, N. B. Strydom

INTRODUCTION Acclimatization of the labour force to heat is an integral aspect of gold mining in South Africa. A recent survey revealed that about 250,000 Bantu mine workers require to be acclimatized to heat each year. Until 1965 men were acclimatized by means of one of the Chamber of Mines methods (introduced by the Human Sciences Laboratory in 1953). This type of acclimatization was carried out underground where men shovelled rock in hot stopes under careful supervision. However, it has become increasingly difficult in the last few years for mines to provide underground the conditions of work and environmental heat required for adequate acclimatization to heat. In examining an alternative to acclimatization in underground hot stopes, the Human Sciences Laboratory carried out a trial in 1965 of acclimatization in an air-conditioned climatic room on the surface of a mine. The new procedures developed from this trial have been so successful that there are today 26 climatic rooms on different mines. These rooms have been built following a design proposed by Mr Hodgson of the National Mechanical Engineering Research Institute1. Approximately 85 per cent of the total number of men being acclimatized each year are put through the new procedures in these climatic rooms. This paper gives an account of the problems which arose and how they were solved, the inter-relationship between physical conditioning and climatic room acclimatization, the prodecures developed for elimination of labourers with low maximum oxygen intakes, and the advantages of climatic room acclimatization. CLIMATIC ROOMS The majority of the climatic rooms (twenty) have been built on the surface, but a number (six) of mines preferred to establish their acclimatization centres underground in order to decrease the initial costs involved in the construction of such facilities. These underground climatic rooms are usually located near shaft stations in redundant haulages and they can accommodate from 200 to 400 labourers, thus eliminating the need for multiple acclimatization shifts. Figs. 1-4 illustrate various aspects of a surface climatic room. PROBLEMS WHICH AROSE IN INTRODUCING CLIMATIC ROOM ACCLIMATISATION There were four main problems which arose in connection with the introduction of the new method. These were: (i) The type and rate of work to be used. (ii) The air conditions required to obtain optimum acclimatization. (iii) The duration of exposure to heat each day and the total number of days of acclimatization. (iv) The methods of cooling labourers with high body temperatures. Shovelling rock would have been the desirable type of physical work to employ, but the air-conditioned space required to accommodate large numbers of men and the difficulty in standardizing the work rate in shovelling led to the decision to employ instead the work procedure used by the Human Sciences Laboratory in acclimatizing men in the Laboratory. This is the lifting of the body weight against gravity when men step on and off a bench. It has the advantage that large numbers of men can work physically at the required rate in a relatively small space (120 men can be accommodated in an area of 70 ft by 21 ft) and the cost of construction and ventilation of the climatic rooms is thereby reduced. Also the work rate can be standardized by varying the height of the stepping benches in relation to the individuals&apos; body weights. The next problem was the air condition to be used in the climatic rooms. The Laboratory&apos;s research experience in acclimatization led it to choose an air temperature of 89°F (with the air almost saturated with water vapour) and an average velocity of air movement of 100 fpm. This air condition was combined with a work rate of 1,560 ft lb/min (oxygen consumption 1.0 litre/min) on day 1, and the work rate was increased gradually over the period of acclimatization to reach a work rate of 3,120 ft lb/min (oxygen consumption 1.6 litres/min) on day 9.

By D. F. Caicedo, I. A. Brum, L. A. Betancourt

Ferricyanide ()()*is one of the most stable cyanometallic complexes present in the gold mining effluents. This cyanocomplex is hard to degrade by natural attenuation and generates a negative impact on aquatic environments. Although free cyanide (CN-) can be obtained by acidifying the solution, the CN- is lethal for all forms of life. The oxidation of ()()* in a typical photocatalitic system was evaluated with the addition of H2O2. To verify the degradation, chemical parameters, such as free cyanide, the formation of ammonia, nitrate, and total iron were analysed at the end of the process. The degradations obtained were up to 70% in a heterogeneous photocatalysis system with TiO2, and a low rate of dissociation was observed by photolysis. The best result was achieved with the H2O2 and TiO2 photocatalytic system, and the stoichiometric concentration was about 2.5 times less than the peroxide used in the real gold mining industry, reaching 83% degradation. The photocatalytic process obtained less toxic byproducts than the original synthetic ferricyanide used as mining wastewater. Keywords: Cyanide, heterogeneous photocatalysis, titanium dioxide, UV radiation, gold wastewater

Jan 1, 2020