Search Documents

By J. E. Chilton

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

Jan 1, 2003

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By A. J. H. Newell, K. Doherty

A copper-gold project has required a number of trade-off studies underpinned by test work to settle on pragmatic flowsheets and throughputs to support a pre-feasibility study that provides a compelling financial case. The primary trade-off studies were based on the mine schedule, ore type feed-grade recovery relationships, likely concentrate grades and typical marketing terms as well as the estimated capital and operating costs for a range of throughputs and mining strategies. Secondary trade-off studies were conducted for specific circuits and additional processing options. Although the details of these studies are not presented, the technical options and subsequent flowsheets are discussed. While the flowsheets will be optimised during the feasibility study stage, the basis is now fixed for the four ore types that would be mined from the copper-gold orebody. The ore types, resulting from a strong weathering profile, exhibit a wide range of copper mineralisation and gold associations, as well as gangue types. They display a range of characteristics that necessitated a nuanced approach to flowsheet development. The primary separation techniques that have been employed include gravity, classification, flotation and leaching while a range of comminution methods have been selected to suit the properties of the ore types. While technical issues are important factors in terms of maximising the quality of separations, recoveries and revenues, attention to material handling, equipment characteristics, the mine schedule, and capital and operating costs are equally important considerations for settling upon a suitable and robust flowsheet. Keywords: Flowsheet, testwork, studies, saprolite gold, native copper, chalcocite, chalcopyrite

Jan 1, 2020

By T. H. Yang, Q. K. Wang, T. Song, J. W. Zhou

The grinding circuit can be one of the most important mineral processing circuits in plants. Along with the application of large-scale milling machines, the design and optimisation of the operation strategy for grinding circuits is more complicated. An in-house grinding process simulation tool was developed to mass balance, model fit and simulate crushing, grinding and classification circuits. An industrial grinding and classification circuit in a copper mine was modelled, and the modelling parameters were verified by a particular group of plant survey data. To justify the prediction ability of the fitted models, the model predictions under different operation conditions were compared with another group of plant survey data. Then the model predicted the effects on the circuit of changing operating conditions. Circuit analysis of the comminution process for water feed to a SAG mill, water feed to sump, the rolling speed of a SAG mill and the percentage of ball filling in a SAG mill was put into practise, based on the simulation results. The simulation results can be used to help plant operators understand the features of the comminution process and may help to build a knowledge library for process control. Keywords: Process modelling, grinding, comminution, circuit analysis

Jan 1, 2020

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By G. Nino de Guzman, L. C. Woollacott

The isotherms that are usually taken to represent the force 'driving' the adsorption in carbon-in-pulp processes may change from contactor to contactor. This paper reports on an investigation into the extent to which this Isotherm shift is Influenced by the changes in oxygen and cyanide concentration that occur in operating plants. The impact of the isotherm shift on the reliability of simulation results is examined.

Jan 1, 1993

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By J. H. Dalton

The paper reviews the effects of fast-neutron irradiation on the tensile properties of austenitic stainless steels at irradiation temperatures of less than 400°C, using, as an example, work carried out at Pelindaba on an AISI 316 type steel produced in South Africa. Damage produced in these steels at higher irradiation temperatures and fluences is also briefly discussed. The paper concludes with a discussion of some methods of overcoming or decreasing the effects of irradiation damage.

Jan 1, 1979

By P. Sharma

Longwall panels facing wind blasts have been investigated at both Newstan and Moonee Collieries in the Newcastle Coalfield under the Wind Blast Project of the School of Mining Engineering, The University of New South Wales. The fluid mechanics involved in the compression and expulsion of air during wind blasts have been defined and the overpressure and air velocity time histories utilized to determine the wind blast parameters and define the relationship between them. The characteristics of wind blasts pressure pulses in mine roadways show some similarity with transient phenomenon like air blasts from explosives and shock waves from the failure of pressurized vessels. The peak wind velocities in roadways, however, exhibit marked deviations from theoretical predictions based on compressible fluid flow and Rankine-Hugoniot relationships applied to goaf air displacement and panel geometry. Peak overpressures and wind velocities have shown a positive correlation with the areas of goaf falls, with the values peaking off for larger areas. The field investigations have helped the mine management in risk assessment and in evaluating the success of induced caving by hydrofracturing to mitigate the hazard.

Jan 1, 2004

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By G. Mahieu, L. Perez-Barnuevo, P. Barbeau-Verreault, O. Gravel

Raglan mine is a copper-nickel mining operation, part of Glencore, and located at the northern border of the province of Quebec, in Canada. The concentrator is fed by a mix of four different underground mines, thus it must accommodate periodic variations in run-of-mine mineralisation and composition. In order to concentrate nickel and copper sulphides, the flotation circuit also includes a regrind step at the cleaner stage. This leads to challenges in maintaining optimal recoveries and in diagnosing potential disturbances. This paper advocates for the combination of automated mineralogical analyses, reconciliated mass balances from diagnostic sampling campaigns and innovative multidimensional visualisation to assist in tackling these challenges. Through this approach, it has been possible to quantify the regrind step influence on the liberation of valuable mineral particles in the final flotation concentrate. The methodology also allows for virtual sieving of the products in order to track unit loss in the flotation process. The proposed analysis scheme presents an opportunity to easily diagnose flotation circuit performance based on mineralogical information. Keywords: Flotation diagnostics, multi-dimensional visualisation, mineral liberation analysis

Jan 1, 2020

By Mike de Wit

Of the approximately 6,500 kimberlites known to date, less than 3% are diamondiferous and less than half of those are economically viable. Admittedly, this is a global figure and varies from area to area much depending on geological, logistical, and political circumstances. The number of diamond-bearing kimberlites is an important geobarometer, and an age-frequency profile has been compiled in order to identify diamond metallogenic epochs and provinces. Four primary diamond clusters have been recognized: Siberia (332-370Ma), Kaapvaal South(114-144Ma), Kaapvaal Southwest(84-95Ma), and Slave (52-55Ma). In addition, three secondary clusters are the Kaapvaal Central (S06-S38Ma), the Man Craton (139-lS3Ma) and the Kasai Craton (120-130Ma). The Kaapvaal is the only area where kimberlites with diamonds were discovered between 1870 and 1925, except for the Prairie Creek discovery in North America in 1906 and Colossus in Zimbabwe in 1907. Between 1906 and 1940 no major diamondiferous kimberlites were discovered, but many of Africa's alluvial deposits were found and exploited in that period. Advances in scientific prospecting in the 1940's rapidly accelerated the discovery rate that peaked in the 1990's; 39 diamondiferous occurrences were found in the 1980's, of which 8 became mines and 5 are in feasibility, and nearly 450ha of kimberlite was added to the global resource base. Despite the accelerated exploration expenditure, the last decade (e.g. 2000-2009) has been the leanest since the 1940's. The most important reason for this decline in exploration success is that any undiscovered deposits are largely buried by younger cover. Understanding complex and geophysical noisy basement geology, as well as decomposition of path-finder minerals are major challenges to further exploration success. Major investments in basic geological expertise and field research will have to be made in order to secure future diamond resources. Integrated geophysical studies, geochemistry diamond forensics, and improved imaging of Earth's upper mantle are perhaps foremost in this requirement, but the costs of these activities are such that government support will be required if countries are to sustain their diamond mining industry.

Jan 1, 2010

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By X. Gumede

Mud houses are common structures in most South African rural homes closer to the mining operations. Fulltime dwellers in these properties are often the elderly. The mine codes of practice and the South African legislative instruments attempt to define the damage criteria to limit the effect of the blast-induced noise and ground vibrations to different structures. All these assessment criteria are based on the peak particle velocity and noise generated during blasting. The South African safe limit criterion that was adopted was initially derived from the international standards, which were then used as a local guideline. This paper evaluates the currently adopted safe limit criteria used in South Africa for a mud house, currently rated at 6 mm per second and 120 decibels to134 decibels, for blast-induced seismicity and noise, respectively. Further, a study was performed on a residential house near a coal mine (5.26 km) based in Mpumalanga following numerous complaints by the owner, launched at the mine and to the Department of Minerals and Petroleum Resources. The aim of the study was to measure the magnitude of blast-induced triggers experienced at the aggrieved homestead and to establish if there is a likelihood that an irritation or damage may be caused by these triggers. The seismometer was installed at about 2 m from the mudhouse, from 1 July 2022 to 31 of July 2022. Five blast-induced triggers were recorded during the period showing an average of 0.09 mm/s and 121 decibels for blast-induced seismicity and noise, respectively. The results obtained indicated a maximum seismicity of 0.15 mm/s. This seismicity was below the perceptible vibrations obtained from daily home activities such as walking, jumping, and door slamming, which produce 0.8 mm/s, 7.1 mm/s, and 12.7 mm/s, respectively. Seismicity was therefore not likely to have caused any annoyance and or damage. For noise, the results indicated a maximum of 123 decibels and an average of 121 decibels from five events recorded. A literature review suggests that slight damage may occur when airblast frequencies match the natural frequencies of structures at 120 decibels. Based on these results, it can be concluded, therefore, that the noise, rather than seismicity, is more likely to be the cause of damage to the structure assessed. For improvement, a new approach is proposed based on relating the safe limits to the structural and human response.

Dec 15, 2025

By J. Thompson

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree A study into the stability of strike gullies at TauTona mine was to be carried out. In reaching the conclusions to follow, a three-stage process was followed. ?A literature study as well as discussions with management and workers alike to gain their inputs and perceptions. ?An ESH Department survey into the history of transgression from proper mine standard in TauTona strike gullies. Unfortunately records were found to be scarce and obscure and the importance of better inter-departmental recordings cannot be stressed enough. ?An underground survey of 11 pre-selected gullies distributed in both the UCL and LCL reef horizons. This stage is to carry the greatest weight in the points to be brought forward in this report. The process highlighted and ranked the following areas as the most critical role players in the deterioration of strike gullies: ?Poor blasting practice ?Sub-standard siding depth and lead-lags ?Split sets ?Off line gully development ?Adverse geological features. The following has been suggested to the mine to help reduce strike gully instability. ?Where possible, maintain lead-lags below 7 m?else increase the siding depth to suit. ?Decrease the gully width standard to 1.2 m (especially in ?high risk areas?). ?Discourage drillers from drilling side holes in gully face blast pattern. This will allow for time in which tendon support can be kept up to date. ?Ensure split sets are installed 1 m behind the gully face so as to prevent opening up of fractures. ?Utilize the centre split set in the 1:2:1 pattern to maintain the proper gully line. ?When adverse conditions prevail, it is necessary to apply a special support plan not only to the panel face, but also (just as importantly) to the gully as well. Shotcreting of the gully hanging is a suitable long-term consideration for providing the additional a real coverage needed. List of Abbreviations [CL Carbon Leader M/O Mine Overseer UCL Upper Carbon Leader FOG Fall of Ground LCL Lower Carbon Leader H/W Hanging Wall ERR Energy Release Rate F/W Foot Wall WDL Western Deep Levels ESH Environmental Safety and Health ]

Jan 1, 2002

By S. J. Ramokgopa

The development of the modern State and the growth of capitalism involves a complex process of interaction between cross-cutting structural dimension: first between politics and economics and, second, between market and hierarchy. Central to such developments are political economies of scale. Mineral specialization in the Third World developed within the framework of an international extension on oligopolistic structure of the advanced capitalist economies of Western Europe and North America. Up to the late 1960s, the world mineral and metallurgical industry was closely controlled by a handful of Western mining and industrial groups. To the extent that, foreign control of the mining sector was seen in the Third World producing countries both as the essence of foreign domination and as its major symbol. In some newly industrializing countries, the State took a more direct role in tying the economy and society together. Central to this process was the growth of large-scale finance capital. From early 1959to the mid-1970s, metal consumption in industrial countries expanded well beyond their domestic mineral endowments. And a free access to Third World minerals was a major element of the economic dynamism of these countries throughout that period. With the change in the characteristics of international investment, Africa has become less important as an outlet for capital exports of European countries. Actually, the African continent now receives only a very minor share of direct foreign investments of Western enterprises. International political economy is concerned first of all with the relationship between the economic and political domains across territorial boundaries. Second, attention should be drawn to the role of the State as the focus of decision-making in a system of competitive States, that is in turn, interdependent with a trans-national market economy in which mining and metallurgy are essential activities that affect the politics of the State, and how this in turn, rebounds on the politics of the international system. Understanding the role of the State must go beyond the glib pronouncements on the ?national interest?. How, and whose interest, the ?national interest? is determined, is precisely the problem. This implies a third theoretical problem that must be addressed: the linkage between the domestic and international domains (or levels of analysis), given that political-economic processes clearly cut across the lines of political decision-making constituted by the institutional structures of the State. Situating the State and economic interests within this vast ?state-society? complex that we call the global order will be a crucial problem for any theoretical approach that involves mining and metallurgy.

Jan 1, 2002

By L. A. Maseko

"As part of the mining engineering curriculum, students are required to be placed in industry for vacation work or work-integrated learning (WIL). In this paper we review work-based placement as done at the four South African mining schools: the University of Johannesburg, the University of Pretoria, the University of the Witwatersrand, and the University of South Africa.Key aspects of past and current WIL (pre- and post-graduation) practices that may need attention are highlighted for consideration by all universities that provide professional qualifications. Work-directed theoretical learning, problem-based learning, project-based learning, workplace learning, and simulated work experiences are discussed as legitimate approaches to WIL.Regardless of the choice each institution makes, commitments of universities, preparedness of university teachers, and the desire for equity and excellence will play an important role in the provision of WIL.DefinitionsAccredited Qualification: a qualification awarded on successful completion of an accredited programme.Advisory Boards (or Committees): are essential infrastructure for a WIL curriculum that is built on the integration of the workplace and the university. This requires the collaboration of experts from both environments. Workplace advisors are critical to the success of the academy as they embody expert knowledge of the ‘real world’.Assessment: the process of determining the capability or competence of an individual against standards by evaluating performance.Category: a mode of registration defined in or under the ECSA Act which has a distinctive purpose, characteristic competencies, defined principal routes to registration, and educational requirements.Experiential learning: (in South Africa sometimes used synonymously with work placement or cooperative education) is a term used with a great variety of meanings in the international literature. More broadly, it may refer to learning that has meaningful learner involvement. It is the process of generating meaning from direct experience. In the international literature, experiential learning is learning through reflection on doing, which is often contrasted with rote or didactic learning."

Dec 1, 2018