Search Documents

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By Roger A. Blais, Michel David

"Matheron's geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By M. F. Dlamini

The hydrodynamics of a hydrocyclone present a complex internal flow structure, the numerical simulation of which remains a non-trivial task. We report on three-dimensional water-only computational fluid dynamics (CFD) hydrocyclone flow field predictions and highlight some of the issues concerned with the development of a CFD model incorporating an air core. The potential for the application of CFD as a hydrocyclone design tool is also discussed. Physically realistic velocity profile predictions were obtained, which challenge the classical account of the hydrocyclone radial particle classification mechanism. A pressure field distribution consistent with literature reports was also predicted. Keywords: hydrocyclone, computational fluid dynamics (CFD),classification mechanism

Jan 1, 2005

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d'emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By S. V. Rungan

The modern mining industry is increasingly being tasked to comply with various legal, industry and social prerequisites. In addition to complying with these, the mining industry is further expected to effectively report on their compliance. Although there are many models that aid the mining industry in compliance and reporting, it is perhaps opportune for a new model to be introduced. The Compliance Spindle is postulated as a new and alternative model which is easy to understand and has the possibility of implementation in South Africa and other jurisdictions as well. The Compliance Spindle is also an effective tool to educate future compliance officers. The new model provides for all aspects of compliance and reporting and can be easily modified to take account of new developments in the mining compliance and reporting arena.

Jan 1, 2010

The Institute has set important objectives for 1988 to make the Institute still more purposeful. Precious metals The Second International Symposium on Mining, Extraction, and Processing of Precious Metals will be held in Las Vegas, Nevada, USA, during the 118th TMSAIME Annual Meeting in March 1989. The First International Symposium on Precious Metals.

Jan 1, 1987

By C. Ware, R. Uken, G. Whitmore

The coastal dune cordon of northern KwaZulu-Natal is among the highest in the world reaching heights in excess of 180 m and up to 2 km in width. It comprises a complex system of Quaternary stacked dunes of various geomorphologies, types and ages (Sudan, 1999; Maud and Botha, 2002;Ware et al., 2001; Ware, 2003). The dunes contain economic heavy minerals that have been exploited for the last two and a half decades. Dune units have recently been defined based on sand composition and texture(Sudan, 1999; Ware, 2003). Despite this, little work has been undertaken on the clay-fraction (< 2 um). This work documents the weathering of dunes to form clays. From the documented clay assemblages and relative abundances, a simplified weathering sequence with increasing maturity can be summarized as follows: primary minerals ? illite + vermiculite ?illite +interstratifications ?illite + montmorillonite ?halloysite + interstratifications + kaolinite ?kaolinite. The dominant controlling factors in determining clay assemblages is pH and leaching conditions. The presence of carbonates results in an alkaline pH and high concentrations of Ca2+and Mg2+which favours the formation of montmorillonite and vermiculite. However, vermiculite tends to form under slightly acidic conditions and is indicative of palaeosols where organic acids produce localized acidic pH’s. In contrast to this, kaolinite will only form and concentrate when carbonates have been leached. Kaolinite dominated samples are considered very mature under current climatic conditions(Chamley, 1989). Halloysite represents a transitional phase between montmorillonite and kaolinite (Herbillon et al., 1981). Ion mobility and evacuation is also critical in determining clay assemblages. Past work and field studies indicate that the dune cordon acts as an open system, resulting in carbonates and mobile ions being readily leached and lost from the system. However, when prolonged weathering has caused an accumulation of fine-grained material, the permeability decreases substantially whereby mobile cations and silica cannot be readily evacuated. This results in the formation of montmorillonite rather than kaolinite, even when carbonates have been leached. Illite (sericite) is considered to alter directly from feldspars. However, dune stacking and geometries, vegetation, water fluxes, reworking and erosion complicates this sequence.

Jan 1, 2003

By K. R. Vost

Variation in air temperature in a cross-section of an underground airway by K. R. VOST, B.Sc. (Glas.), M.Sc. (N.S.W.) (Visitor) Measurements of air temperatures in underground airways are normally made at only one point in a cross-section, and the air tem peratures at other points in the cross-section are assumed not to differ significantly from this. This paper discusses measurements made at a number of points in fifty crosssections in airways with different air velocities and wetness of floor. These measurements show that significant variations of air temperature can occur in a given cross-section at a given time. The effects of such variations on the accuracy of measurement of rises in air temperature as air passes along an airway are discussed. The importance of considering experimental error in the measured rises in air temperature when attempting to validate theoretical and empirical methods of predicting such rises is also discussed.

Jan 7, 1976

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004

By A. M. Bryukhanov, A. G. Mnukhin

The report states accident rates for gassy/dusty coal mines represented as an ergatic system "man – machine - environment" with further analysis by the method of conditional probabilities. A coal mine has been analyzed with allowance for the attending personnel, equipment and environment as a sequence of events and states. Probabilities of operational states have been determined and prediction of mine behavior has been made on the basis of investigation findings for equipment and the personnel states, and analysis of the environment (i.e. mine and mining conditions). Utilization of expert estimation methods has been considered for determining major operational parameters of gassy/dusty mines. The importance of standardized values of permissible occupational risks (permissible probability of accident, PA) is demonstrated. It is also stated that a procedure is essential to determine these values, involving regular check-ups of the integral safety criterion at all mines and further development of customized recommendations for individual mines on efficient improvement of accident situations. Methodology to determine the assessment criteria has been developed and scientifically substantiated for permissible accident rates in hazardous industries.

Jan 1, 2003

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

By S. Fuchida, Y. O. Zubair, C. Tokoro

Mining of As-bearing minerals had resulted in the release of arsenic species predominantly As(III), which is known to be more toxic, and undue exposure to it is detrimental to human organ systems. Many materials have been examined for As(III) removal, but it is still challenging to advance sustainable materials for effective removal of As(III). In this paper, a more eco-friendly and superparamagnetic Fe0-Fe3O4 composite was synthesised and evaluated for heterogeneous catalytic oxidation and removal of As(III) with peroxymonosulfate (PMS, KHSO5). The kinetic removal studies showed that removal of As(III) was probably through a chemical process and the Elovich model best represented the experimental data. The removal capacity for As(III) on Fe0-Fe3O4 with PMS (1.76 mmol/g) is superior to that without PMS (0.83 mmol/g). Combined results from XPS and ESR showed that As(III) was fully transformed to As(V) through catalytic oxidation by Fe0-Fe3O4/PMS and afterwards enhanced its removal. The removal mechanism of arsenic was ascribed to the formation of outer-sphere (electrostatic attraction) and inner-sphere complexes. The adsorbent can be separated easily from water due to its excellent magnetisation (64.5 emu/g) and also has good reusability potential as more than 85% of the initial concentration of As(III) was immobilised after five consecutive cycles. Keywords: Arsenite, Fe0-Fe3O4 composite, catalytic oxidation, removal mechanism

Jan 1, 2020

On behalf of the Council and staff of The South African Institute of Mining and Metallurgy, it is my privilege to wish all members and subscribers a very Happy Christmas and a Prosperous New Year.

Jan 1, 1988

By K. Sasaki, S. Kuroiwa, H. Miki, Y. Aoki, T. Hirajima, Y. Orii, G. P. W. Suyantara

Selective flotation to separate copper minerals from, for example, Mo- and/or As-bearing minerals is a continuing problem because the selectivity of current systems is imperfect. Selective Cu-As flotation is currently difficult, and the most common Cu-Mo selective flotation method uses NaHS; this must be done in an enclosed system because, under acidic conditions, this method produces hydrogen sulfide. In this paper, some novel alternative flotation processes that use redox reactions are discussed; these methods have a much lower environmental impact. Oxidation and reduction reactions can be used to make copper minerals more hydrophilic and Mo-bearing minerals more hydrophobic. X-ray photoelectron spectroscopy (XPS) analyses indicated that the copper minerals became hydrophilic because hydrophilic iron precipitated and several hydroxides covered the copper minerals’ surfaces, whereas the molybdenum minerals remained hydrophobic because their sulfide surfaces were not covered. Flotation experiments on these minerals after redox treatments indicated that excellent separation of Cu-minerals from Mo-minerals can be achieved. Possible mechanisms for this separation were investigated using detailed surface analyses and thermodynamic calculations. The additives used to initiate the redox reactions are easy to handle and make these new flotation procedures better than current processes because the new methods do not emit effluent gas and because they are commercially viable. Keywords: Flotation; chalcopyrite; molybdenite; oxidation; reduction

Jan 1, 2020

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By F. S. A. de Frey, F. C. Kruger

Personnel management has undergone a remarkable change over the course of the past ten years. Personnel departments have played an increasingly important role, which today requires highly trained people and cannot be adequately served by the lesser qualified officials of yesteryear. Changes in the mining industry that stem from the demand for skilled labour to keep pace with technological developments and the mechanization of mines today demand that emphasis should be placed on the maximum utilization of manpower. Maximum utilization of manpower calls for more scientific and effective methods of recruiting, selecting, training, and placing workers so as to offer them the best opportunities for development and promotion, which naturally ensure a minimum labour turnover and eliminate labour unrest. This can be achieved only if well-qualified and properly trained personnel administrators are prepared to accept the challenge and apply themselves purposefully by assisting line mangement with the attainment of the company&apos;s corporate objectives.

Jan 1, 1982