Search Documents

By H. Wagner

The paper points out that bord-and-pillar mining is the most important method of coal extraction in South African underground coal mines, and advocates that pillar design procedures should be refined to make more rational allowance for the differences in strength properties between various coal seams and roof and floor strata. However, any deviations from well-established design procedures must be based on sound engineering principles and reliable data on the strength properties of the seams and strata concerned. Recent information indicates that practices for the protection of surface structures against underground mining should be revised.

Jan 1, 1980

Anglo Platinum commenced commercial underground borehole radar (BHR) surveys during 2006 following a series of trial surveys using both the ?slimline? Geomole and Aardwolf systems. Current borehole radar systems comprise radio frequency transmitter ? receiver antennae operating at 30 -100MHz that measure the time taken for a transmitted pulse to traverse a rock volume and be received (Fig 1). The time taken can be converted to distance if the transmission speed of the pulse through the rock volume is known. The transmitted pulse may be reflected off a suitably orientated geological reflector (in reflection mode) or may be recorded in receivers located in other boreholes (cross-hole tomographic mode). In the Bushveld Complex lithologies, these radar systems have ranges of 30-50 metres in reflection mode depending on the electrical properties of local stratigraphic units. Both the Merensky Reef (MR) and the underlying UG2 have been shown to act as reflectors, which offer the opportunity of using BHR as an imaging or mapping tool. Reflection of the radar signal occurs wherever a strong contrast in dielectric constants occurs such as between norite and harzburgite or where chromitite stringers are present. [ ] Fig 1 Main elements of a borehole radar system Much experience has been gained in the practical application of BHR surveys in platinum mining. The value of a BHR survey is that it provides a continuous line of information to ?connect the dots? rather than a few discrete pierce points. BHR surveys can be used to mitigate risk in three crucial areas: ? Mine planning at the strategic as well as tactical level ? geotechnical evaluation of proposed shaft sites, detailed profiling or mapping of reef and disruptions of the reef such as faults, rolls and potholes; ? Mineral resource classification ? identification of structural discontinuities in orebodies affecting resource classification e.g. potholes and reef facies; ? Safety ? identifying areas with poor ground conditions that are often associated with faults, dykes and potholes.

Jan 1, 2007

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By D. A. J. Ross-Watt

Right now the South African mining industry is a high-profile, vital contributor to the nation just as it has been for the past one hundred and twenty-six years since the discovery of diamonds-perhaps even further back if the mining of copper, iron ore, tin, and other minerals in earlier centuries is included. The media in 1995, as has been the case over the years, bear testimony to the complex interactions between the industry and its stakeholders: shareholders, government, employees and their unions, training and educational institutions, researchers, markets, the public, and suppliers of goods, services, and infrastructure. The pressures and challenges that the industry continues to face can be summarized as safety and health, competitiveness, and social and environmental responsibility. There are no surprises here. The motivation for the industry to perform well in these areas is clear; the focus I intend to bring is on the most important tool required for success-that of good mining engineering. This Address sets out - to review the mining aspects that have been discussed in South Africa during the first five years of the decade, a discussion that shows the return of the country as an important mining forum, confirms the role of professional institutes and associations in the development of mining engineering, and brings current relevant issues into focus - to highlight the vital role of mining engineering in the industry, and to identify priorities for the remainder of the decade - to provide the prospective mining engineer, the mining-engineering student and trainee, and the practising mining engineer and mine manager with a better appreciation of the mining-engineering discipline. institutes and ssociations

Jan 1, 1995

By C. Legote

"This paper investigates the conditions leading to the indefinite termination of production in four critical primary panels at an underground coal mining operation, the observed shortcomings in the mining approach, and the proposed strategy to mine through the affected panels. Initial assessment of the abandoned panel conditions indicated time-dependent strata failure,(i.e. bolted roof failure overrunning intersections), which occurred from mere minutes to up to four weeks post-production, with and without prior warning of failure. This prompted the constant re-supporting of back areas, which raised safety and productivity concerns. Investigation of the initial mining conditions revealed that the failures were due to a critical combination of factors, the chief of which was isolated horizontal stress. Other factors that were initially overlooked by the mine (i.e. influence of hydraulic stress, misinterpretation of borehole data), resulted in the conditions being described as abnormal. Remedial actions were determined, and in so doing, a new strategic approach was formulated to thoroughly address all failure concerns. The four panels were explicitly planned to serve as the main intake and return airways for the recently commissioned secondary ventilation shaft, as well as providing access to millions of tons in proven coal reserves. It is thus imperative to mine the panels. A feasibility study showed that the proposed strategy set for implementation would be financially viable. Paper written as project work carried out in partial fulfilment for BEng(Mining Engineering) degree"

Jan 1, 2015

Bacterial leaching represents an unusual problem in biochemical engineering, because the substrate for bacterial growth is not supplied directly, but is a product of another reaction, the leaching of mineral particles. Leaching arises from the bacterial oxidation of ferrous ions to ferric ions, which in turn oxidize the mineral. For the bacterial dissolution of pyrite, these reactions are: [ ] (Y represents a stoichiometric yield factor, and N represents the amount of bacteria.) Equations [1] and [2] represent a cyclic auto-catalytic system since more ferric ions are added to the system with an increase in the extent of leaching.

Jan 1, 2000

By C. L. Workman-Davies

Noise is a form of pollution arising mainly from the activities of man. One such activity is mining, in which man, as in many of his other activities, uses machinery of various kinds to achieve safe, healthy, and economic production. Trackless mining makes use of an advanced state of technology over that required In traditional mining methods. One of the advantages of the former, as distinct from any disadvantages it may have, is a reduction in noise levels, the number of people exposed to noise, and the duration of their exposure to noise. This paper briefly examines why noise is a problem and what various countries are doing about it in terms of standards, codes of practice, and regulations. It also investigates the extent to which noise is a problem in mining and how trackless mining alleviates this problem. The question is then posed as to whether South Africa is not setting too high a standard at this stage of its national development by comparison with what is being done by other, more-advanced countries.

Jan 1, 1989

By J. M. Schaekers

In the first part of the article, the authors give a broad overview of the chemistry and some engineering aspects of bioleach processes, eventually leading to the important and critical issue of the stability of arsenic-containing residues, especially those derived from bioleaching of sulphidic gold ores. In the section ?Factors affecting arsenic stability? they give an excellent summary of the factors normally affecting the stability of such residues. This is followed by some valid comments on the suitability of a single leach test to evaluate the long-term stability of solid waste streams. However, they fail to mention that, up till now, no tests procedure has been accepted by either environmentalists or the mining/processing industry as a valid method to test the long-term stability of solid wastes. Their own method is no exception, although, like many others, it is useful to identify potential problems with solid wastes considered for disposal.

Jan 1, 2001

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL)?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By P. W. J. van Rensburg

COLLOQUIUM AND GENERAL MEETING A General Meeting and Colloquium on comminution was held on March 13th, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 140 delegates and was opened by the President at 9.15 a.m. MINUTES The minutes of the general meeting held on November 14th, 1973, as published in the December issue of the Journal, were confirmed.

Jan 5, 1974

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

By G. Vouille, P. Bérest

Residual stresses observed in rocks often result from non-compatible initial strains. These stresses can be determined when the incompatibility tensor associated with the initial strain tensor is known. The residual stresses in a cylindrical rock sample can be computed the sample is considered small enough for its incompatibility tensor to be constant. Les contraintes résiduelles, dont on observe couramment les manifestations dans les roches, résultent souvent de l’existence de déformations initiales non-compatibles. Ces contraintes peuvent être calculées lorsque le tenseur d’incompatibilité associé aux déformations initiales est connu. Les contraintes résiduelles dans une éprouvette cylindrique sont données dans le cas où le tenseur d’incompatibilité est constant. Eigenspannungen, die man haeufig in Steinen beobachtet, sind oft Ergebnis einer inkompatiblen Deformation des Anfangszustandes. Diese Spannungen koennen berechnet werden, wenn der Inkompatibilitaets-Tensor der Anfangsdeformation bekannt ist. Die Eigenspannungen einer zylindrischen Probe werden fuer Fall eines konstanten Inkompatibilitaets-Tensor bestimmt.

Jan 1, 2003

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper/gold mine has continued to process significant quantities of complex transitional mixed ores. The effect of the complex mineralogy on the flotation performance is depicted. Initially, ore treated came predominantly from accumulated stockpiles. In the ensuing years, ore treated shifted to primarily freshly mined ore that generally showed less tarnish with better float kinetics but with the downside of producing lower concentrate grades. A number of changes were made to improve the efficiency of the roughing circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory float test work done and discussed at length in a previous paper. Salient among the adopted recommendations from previous work were increasing circuit capacity and modifying configuration to increase the residence time and the number of sulphidisation stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and subsequently below-specification final concentrate product. This was primarily due to higher mass pulls resulting from the extended rougher bank with multiple concentrate discharge streams. This necessitated the need for an enlarged cleaning capability to offset this. The extra cleaning capacity came on-stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. INTRODUCTION The Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining PLC, a First Quantum subsidiary. The remaining 20% is owned by the state through the parastatal ZCCM. The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005. Prior to June 2009, Kansanshi mine treated only two ore types: oxide and sulphide. All transitional ores mined during the period leading up to 2009 were stockpiled. The treatment of the minerologically complex, transitional ores through a third train commenced in June 2009 but with numerous metallurgical challenges. This transitional ore (called mixed ores) could not be previously treated economically due to high gangue acid consumption (GAC) minerals association (making it unsuitable for the oxide float–leach circuit) and poor flotation response ruling out the conventional sulphide float circuit. The new novel circuit involved a conventional sulphide pre-float followed by flotation involving staged controlled potential sulphidisation (CPS)."

Jan 1, 2015

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008

By D. F. Malan, Y. Jooste

"SynopsisScattered mining was practised on Kusasalethu Mine (previously Elandsrand Gold Mine) prior to 1998, but at deeper mining levels it was no longer feasible, since it would have resulted in unacceptably high stress levels and energy release rates. Longwall mining was not adopted at these depths as the mine required a more flexible mining method owing to the highly variable grade and the presence of geological structures. A mining method was developed that consisted of dip stabilizing pillars for regional support, as well as bracket pillars to clamp geological structures. A strict sequence of extraction was followed and this, together with the particular layout, was called the ‘sequential grid mining method’. This method addressed two key problems, namely negotiating adverse geology and the erratic grade of the Ventersdorp Contact Reef (VCR) orebody. However, a significant drop in production rates resulted in the need for alternatives and improvements to the original mine design. Modifications to the design were proposed in order to increase production rates, and an investigation to consider the rock engineering implications of these modifications was conducted. The study indicated that the modified method, called the ‘multi-raise mining method’, appears to be feasible and might address some of the production problems that were experienced with the original sequential grid design. An analysis of actual seismic data showed no significant differences between the original sequential grid mining and the implemented multi-raise mining. The numerical modelling of the mining layouts showed slightly higher interim energy release rates (ERRs) and average pillar stress (APS) levels during the extraction process. The final values are nevertheless identical to that of the original sequence. The study also investigated the use of a modelled moment method to analyse future seismic trends. The study illustrated that the expected seismic trends will be very similar for the multi-raise method compared to the original sequential grid mining method. This study is nevertheless considered of a preliminary nature and ongoing monitoring and analysis of seismic data at the mine is required to verify the response of the rock mass to the modified sequence and increased extraction rate. In particular, future work needs to investigate the effect of mining rate (advance rates in individual panels as well as volume of mining in particular raise lines) on the level of seismicity."

Jan 1, 2015

By A. N. Brown

The importance of the minerals industry in the economy of the country is discussed, and the tremendous changes that have taken place over the past two decades, including the widespread application of computers and the use of mechanization, are outlined. A discussion of the future of the minerals industry points out that, with the rise in the price of gold, the life of the gold-mining industry can be expected to extend beyond that previously predicted, and that the demand for uranium, which has been depressed, is uncertain. As a result of the oil crisis, the demand for coal has increased and large expansion programmes are planned. These involve coal exports and the use of coal for the generation of electric power, for the production of liquid fuels, and for the smelting of metals. Technical challenges face engineers in every avenue of the minerals industry: in deep gold mines, underground coal mines, strip coal mines, and open-pit mines. Studies indicate that only one-third of the demand for trained mining and metallurgical engineers is being met and that the position is worsening. However, there are indications that the industry is succeeding in attracting more engineering students, and the supply is expected to improve. These efforts should be co-ordinated, expanded, and intensified. There is a need to ensure that sufficient teaching staff of the right calibre and experience are attracted to universities and technikons. The first degree course is comprehensive and basic, and specialization through post-graduate study should be encouraged. The influence of national service on the education and training of engineers is discussed.

Jan 1, 1982

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By M. Rudolph, R. Tolosana-Delgado, G. van den Boogaart, M. Reuter, U. Peuker

This paper addresses the challenge to define a concept of entropy (state of order) for a textured particle system. Both the particle texture, the intergrowth respectively, and the particle size influence the order of a particle system. The smaller the particles become, the more particles form the solid system and the more permutations of the structure of the particle bed are possible. The texture within a particle is fixed, as long as it is not subjected to changes due to comminution, flocculation or agglomeration. The paper will present a definition of entropy, which is able to reflect qualitatively and quantitatively the intergrowth and the size (distribution) of the particles. Theoretical examples will show how different breakage mechanisms can be identified using the entropy definition. Furthermore, we will define the specifications for data sets to calculate the entropy of a particle system. Keywords: Milling, mineral liberation, intergrowth, statistical entropy, modelling

Jan 1, 2020

By D. J. Burger

This paper will highlight the system components of a successful underground mining automation project recently launched at DeBeers Finsch Mine. It will also show that integration of short-term mine planning with other upstream and downstream mining processes in the extraction of kimberlite ore from a block cave is not just critical to the future sustainability of this underground mining operation but also for profitability and cost-effectiveness. This paper will discuss the information data flow required from the mine-planning process through to production for underground block cave mining. The benefits associated with this type of integrated mine planning and automation system will be highlighted.

Jan 1, 2006

By Y. -J. Park, K. -H. You, Y. -T. Choi, Lee. H. -W.

Many large caverns are being constructed in great depths in Korea mainly for the storage of oil and LPG. These caverns are mostly located near the port where rock conditions are reasonably good. In some instances, the horizontal stress is very high and endangers the stability of the cavern. The purpose of this study is to assess the stability of large caverns excavated in a rock mass with high horizontal stress where Ko value is close to 3. Result shows that stress exerted in the shotcrete at crown exceeds allowable value when the 3rd bench is excavated. Also found is the tensile failure of shotcrete near the boundaries between benches. In Korea werden viele grosse Kaverne fuer Aufbewahrung vom Oel und Fluessiggas in grosser Tiefe gebaut. Am Meisten befinden sich diese Kaverne in der Naehe von Haefen, wo der Fels gute Verhaeltnisse zum Bauen einer Kaverne besitzt. In einigen Faellen ist die Horizontalspannung sehr gross und dadurch wird die Stabilitaet vom Kaverne gefaerdet. Der Zweck dieser Arbeit ist die Stabilitaet des im Fels gebauten grossen Kavernes mit hoher Horiaontalspannung zu schuetzen, wo Ko-Wert sich auf 3 naehrt. Die Ergebnisse zeigen, dass die Spannung im Spritzbeton an der Krone den zulaessigen Wert ueberschreitet, wenn das dritte Bank ausgegraben wird. Im Bereich des Spritzbetons zwischen Baenke wurde das Zugversagen festgestellt. Des larges cavités nombreuses sont en train d’être construites en grand profondeur en Corée prin-cipalement pour le stocage du pétrole et LPG. Ces cavités sont pour la plupart situées près de la porte oú les conditions des roches sont résonablement bons. En quelques cas, la contrainte hori-zontale est trés haute et met en danger la stabilité de la cavité. L’objet de cet étude est d’estimer la stabilité des large cavités excavées dans une masse de roche ayant une haute contrainte horizontale oú la valeur de Ko est proche à 3. Le résultat montre que la contrainte exercée dans le shotcrete à la couronne dépasse la valeur admissible quand le troisième banc est excavé. En plus une faillite en tension du shotcrete près de la frontière entre des bancs est trouvée.

Jan 1, 2003