Search Documents

By A. Smith

After the introduction of mechanized bord-and-pillar development at Dumacol in 1958, pillars were being developed at a much faster rate than they could be extracted by hand loading methods. Efforts were therefore made to increase the rate of pillar extraction by mechanization. Following two partially successful mechanized stooping trials in 1964 and 1971, it was decided that mechanized pillar extraction with 1 m3 cable-reel front-end loaders should be introduced. The first section to employ the new equipment started production in May 1979, and the mine now has four mechanized pillarextraction sections in operation. Considerable improvements in production, productivity, safety, and percentage extraction have been achieved.

Jan 1, 1985

By H. P. Carlisle

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER and G. M. KOEN Published in the Journal. February 1973. DISCUSSION H. P. Carlisle. B.Sc. (Eng.) Rand (Fellow) The authors are to be congratulated on drawing attention to the importance of surface characteristics in the treatment of gold grains. I must, however, confess to considerable doubts about the validity of the distribution of gold in "free" and "locked" form set out in Tables I to IV.

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By R. R. Mankowski

The work described here attempts to underscore the importance of the time lag between the end of a loading phase and the instant a winding drum begins its acceleration phase. Traces generated from a computer-simulation model show that the amplitude of the stress oscillations occurring in mine hoisting cable during the constant velocity-of-ascent phase is a direct result of the temporal sequence employed between the loading and the raising phases. While current and early literature indicates that extensive work has been undertaken on the isolated effects of these two independent sequences, the literature does not appear to contain any documented evidence to suggest an optimal control or interfacing between these two dynamic regimes.

Jan 1, 1995

By Dr. T. L. F. Muller

INTRODUCTION During the past decade a wealth of knowledge has been acquired about the mechanisms and reactions responsible for the physical properties of metals. In the field of steels, in particular, research of a fundamental nature has enabled us to interpret mechanical properties such as hardness, brittleness, creep strength, etc., in terms of atomic interactions. So rapid has been the development of physical metallurgy in some fields that publications are often outdated by the time they appear in print. The development of new steel products has been rather empirical by nature in the past and only during the past few years have new products been "designed" in terms of known physico-metallurgical phenomena. However, although this is a great stride forward it should be added that the development of a commercially successful product is a far more complicated process. In addition to the physico-metallurgical background this requires consideration of factors such as low production cost, market research and probably most valuable of all, an interested end user to co-operate in the development. This paper deals rather briefly with three of the most recent developments in steels in Britain with which the author has had some association. The main purpose of this is to demonstrate how the improved properties of the new product are based upon established physico-metallurgical phenomena. Generally speaking a commercially successful product of the type described here offers similar properties to that of an existing product at lower cost or has improved properties or features such as greater ease of cold forming, at similar cost. ULTRA-FINE GRAIN STRUCTURAL STEELS The development of higher yield strength structural steels dates back over a considerable number of years and has led to a variety of types. The one described below contains niobium as a grain refiner in an otherwise conventional mild steel matrix. By controlled rolling in a strip mill considerably increased yield strengths are obtained. In Fig. 1 are shown somewhat diagrammatically the relative hardening effects of carbon and manganese on ferrite. It will be seen that strength is enhanced by the solid solution hardening effect of manganese and the pearlite content. An obvious limitation of high pearlite content is a lack of cold workability and weldability. Manganese has to be restricted to low levels for the same reasons. The two other mechanisms which are known to impart higher strength are precipitation hardening and grain refinement. Precipitation hardening is impractical in most cases for structural steels and it is therefore clear that only grain refinement remains as a potentially useful strengthening mechanism.

By Z. Yang, X. Bian

"The synthesis of 3-hydroxy-2-naphthyl hydroxamic acid (H2O5) as a collector for bastnaesite is described. The flotation performance of H2O5 with respect to bastnaesite was investigated by flotation tests, measurements of the surface adsorption capacity, and polarizing microscopy. The results indicated that H2O5 exhibits superior collecting performance compared with direct flotation recovery of bastnaesite, with recoveries above 90% at pH 8–9. The adsorption mechanism of H2O5 on bastnaesite was studied by solution chemistry analysis and ?-potential tests. The results showed that the adsorption of H2O5 is associated with the types and concentrations of hydrolysis products of rare earth cations on the bastnaesite surface. At pH 8–9, the hydrolysis-dominant components RE(OH)2+ and RE(OH)2 + of the rare earth cations were adsorbed onto the bastnaesite surfaces, which were considered to be the major positive active points and were beneficial to chemical adsorption of the reagents. The pH range of 7–10 was optimum for bastnaesite floatability, and the adsorption of H205 on bastnaesite was by means of chemical adsorption through formation of a five-membered ring chelate. IntroductionThe rare earth elements (REEs) have long been known as ‘industrial gold’ and are widely used in the petroleum, chemical, ceramic, metallurgical, and permanent magnet material industries because of their special physicochemical properties (Chen, 2011; Krishnamurthy and Guptac, 2002; Esquivel, Bohe, and Pasquevich, 2002; Abrahami, Xiao, and Yang, 2015). Demand for REEs is growing in response to continuous advances in science and technology. Currently, most REEs are extracted from bastnaesite ((Ce,La)CO3F) (Chelgani et al., 2015; Yosry, 1990), which is recovered from rare earth ores by flotation. Typically, hydroxamic acids are used as bastnaesite collectors (Xu, 2015; Ren, 1997; Mousumi and Venugopal, 2016). Research into the mechanism of interaction between hydroxamic acids and bastnaesite is important for improving the recoveries of bastnaesite. However, there have been few studies that examine this mechanism."

Jan 1, 2017

By B. A. Dukas

The diamond-drilling machine has for many years been the most important exploration tool In the search for and subsequent evaluation of Witwatersrand-type ore deposits. With a view to increasing the range of services that can be provided and, at the same time, counteracting rising drilling costs, new techniques are continuously being developed. Many of these techniques have equal application in surface and in underground exploration. This paper reviews drilling techniques such as non-coring pilot holes and deep wire-line drilling, as well as the design of core-barrels and drilling bits to cater for the specific nature of the job on hand. Special drilling fluids and aluminium rods to assist in normal drilling operations are also discussed. Special mention is made of a bore hole's natural tendency to deviate in a certain direction. The factors that cause deviation are used to the advantage of controlled drilling techniques.

Jan 1, 1983

By M. D. G. Salamon

In view of an urgent need for a simple means of simulating the behaviour of stratified rock masses, a long-dormant linear model is revived, generalized, and discussed in some depth. The model is piecewise homogeneous, consisting of a pile of homogeneous isotropic laminae in which the interfaces between beds are parallel and free of shear stresses and cohesion. The continuity of stresses and normal displacements is assured across the bedding planes and, to maintain simplicity, the theory of thin plates is used as the kernel of the model. The paper covers the case where the rock mass consists of discrete beds in which the layers are arranged either heterogeneously or systematically. The stratification is regarded as uniform when all the layers are of the same thickness and their Young's modulus changes exponentially with depth; and as homogeneous when all the laminae have identical thickness and properties. The case of uniform stratification is also treated on the basis of an equivalent quasi-continuum derived from the basic model. Attention is focused on the derivation of influence functions. It is demonstrated that the quasi-continuous models, when they are available, can replace their distinct-layer counterparts. The homogeneous quasi-continuum, which permits the derivation of its influence functions in closed form, facilitates the determination of the roof and floor convergence. In the case of a significant class of problems, the convergence distribution is defined by a second-order differential equation in the xy plane, which simplifies to a Poisson's equation if the mining excavations are unsupported. With this result, the paper prepares for the solution of a host of practical problems. These solutions are presented in a series of papers that are in the course of publication.

Jan 1, 1991

By H. M. Friede

Discussion of the above paper by A. SIFF The steely nature of the Iron Age objects mentioned in Dr Friede's paper point to two hypotheses. (1) The African iron workers were conversant with the art of direct steel manufacture. (2) They were less knowledgeable of the art of the production of carbonless iron. In this context I cannot but quote T. A. Wertime.

Jan 1, 1980

By C. J. Van Niekerk, D. R. Allen

The electrolytic extraction of zinc at the Zinc Corporation of South Africa Limited by C. J. VAN NIEKERK, B.Se. (Hons.)(Poteh.), M.Se. (Unisa)(Fellow) and D. R. ALLEN, A. Met. (Sheffield) (Member) This paper gives a brief account of some modifications that were made to the process of zinc electrowinning practised by the Zinc Corporation of South Africa Limited. Some changes in the materials of construction are also described.

Jan 2, 1977

Statistics is essentially a study of variability, the use of some suitable mathematical model representative of such variability, and the application of this inferred pattern of behaviour to practical problems. Probability theory is the mathematical structure devised for providing models for chance happenings. Perhaps the simplest example of a chance happening is the result obtained in tossing a coin. Although the result of a single toss can never be predicted with certainty, there is no reason why in repeated tosses the expectancy of heads and tails should not be equal. In such a case the outcomes of the experiment are said to be equally likely, so that the probability of obtaining heads (or tails) is 1 in 2, that is, 0,5. This simple probability .model refers to a 'mathematical' or 'unbiased' coin. Whether such probabilities are meaningful for actual coins tossed in any particular way is a matter for experience to determine. Probability models have also provided the basis for representing observed variability in cases where the actual under- lying probabilities are only partly known or defy analysis. A typical example of the latter case is the variability observed in the values obtained from gold or other ore samples. The interacting natural forces which gave rise to this variability are obviously very complex and are unlikely ever to be unravelled completely. In spite of this, probability theory and the more recent geostatistical theories have provided us with models which can represent this variability on a reasonable basis. Applied statistics and geostatistics must therefore never be accepted as exact mathematical sciences. Furthermore, a basic and essential concept is that in the type of applications covered in these notes, no model must ever be accepted as necessarily the final and exact answer to the problem; thus, any model must prove and continue to prove its appropriateness in practice, preferably by follow-up comparisons.

Jan 1, 1981

By F. W. Petersen

For the past thirteen years, the Universities of Cape Town and Stellenbosch have hosted an annual symposium to discuss topics relevant to mineral processing. Since 1987, this Symposium has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has become one of the main events on the national conference calendar. In 1989 and 1993, the symposia took the shape of international conferences. This year the 13th Annual Mineral Processing Symposium was organized by the two universities, the Cape Technikon, and the local branch of the South African Institute of Mining and Metallurgy, and was held at the Van Riebeeck Hotel in Gordon's Bay.

Jan 1, 1994

Mr J. Meintjes (Chairman) was in the chair. There were also present: 7 Members: Messrs B. D. McNeice, A. Bain, G. E. Carlyon, C. H. Coxon, B. F. v. d. Merwe, A. C. Hofmeyer, H. J. R. Way. 4 Associate Members: Messrs E. J. Jackson, A. C. Melvill, W. Weber, R. E. Powell. 2 Visitors. It was decided to have the visit to ETC at Barberton on 20th March. A programme will be sent to all members who indicated that they wish to go on this visit. A talk on "Billet Casting of Ferrochrome" was given by Mr. B. F. van der Merwe. After question time the chairman thanked the speaker and asked for the talk to be forwarded for possible publication in the Journal. The meeting closed at 9.10 p.m.

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012

By J. H. Venter

The accuracy of estimation from samples of ore in bulk By J. H. Venter Published in the Journal April 1972. ERRATA: Equation (1) should read... Equation (3) should read .... line following "Duscussion" Delete" .... Insert... above "References" "Discussion". Replace .... tenth DISCUSSION M. DA VID Professor Venter has proposed a formula to compute the variance of the estimated grade of a lot of broken ore, and interesting comments on the relevance of the formula and suggestions for developments are made by P. R. Janisch.

Jan 4, 1972

By J van Rooyen, S. Archer, M. Fox

The use of dilute sulphur dioxide (SO2) gas mixtures for the oxidation/precipitation of manganese has been explored widely in recent years. The technical merit of the concept is well proven and implementation of the technology on commercial scale is imminent. This paper reviews the technology of manganese removal by means of dilute SO2 gas mixtures and highlights some of the challenges associated with its implementation on industrial scale. A brief review of the technology is presented; the review considers both the mechanism and chemistry of manganese oxidation/precipitation with dilute SO2 gas mixtures. The impact of variables such as temperature, pH and SO2 concentrations on the manganese removal process is assessed. Challenges associated with implementation of the technology on industrial scale are discussed. Gas dispersion is highlighted as a critical design consideration.

Jan 1, 2007

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By deur R. R. Mears

The expected curtailment of activities within the gold-mining industry by the closure of the more marginal mines, and the shortening of the life of the industry as a whole as a result of rising costs and/or an uncertain gold price, are factors that are bound to harm the South African economy in a number of ways. The industry has no option but to regard the gold price, which is determined on the world market, as a given quantity. The remaining ore reserves al tend to be of a lower grade and/or to be found at greater depth. Therefore tighter control of working costs would seem to be almost the only option open to the industry. Working costs can be divided into two broad categories: costs emanating from the environmental characteristics of the orebody, and costs emanating from the general inflationary environment in which the industry has to purchase its inputs. Working costs stemming from the physical environment also fall into two categories: those relating to the grade of the orebody, and those resulting from working at increasing depth and temperature, together with the need to pump increasing quantities of water. The industry is both capital- and labour-intensive in absolute terms, since it requires large inputs of labour as well as of capital. It is limited in its scope to adjust its production function by becoming more labour- or more capital intensive, and is dependent on a large labour force, which cannot easily be replaced by capital inputs. On the other hand, large amounts of capital are required for investment in shafts, development, machinery, and equipment. Since the early seventies, the working costs of the South African gold-mining industry have increased at an annual rate that was significantly higher than the general rate of inflation. This rapid rise in working costs has caused some mines to find themselves in a difficult profit position. At times, the gold-mining industry has even been compelled to restructure its cost/revenue relationship rather fundamentally by revising the grade of ore worked sharply upwards or downwards, as the case may be. The rise in the gold price since 1972 has made it possible for the industry to introduce significant changes in its Black wage policy. The main aim was to increase the permanency of the Black labour force and to encourage local Black workers to join the industry. At the same time, significant increases were also experienced in the cost of machinery and stores, as well as of capital, mainly as a result of inflation. In the study on which this paper is based, the author attempted to measure the influence of environmental factors on working costs, using the physical consumption of electricity as a criterion for measurement. He found that the usefulness of this criterion in relation to factors such as depth, temperature, and water quantities pumped was invariably more than neutralized by the effects of greater productivity and economies of scale. The effects of these environmental factors on the working costs of the industry could therefore not be determined to any degree of accuracy. It seems that good progress is being made with the development of capital-intensive forms of technology aimed at coping with rapidly rising working costs and other effects of increasing depth. Techniques are also being developed to improve rock-cutting procedures and to eliminate the use of explosives in order to introduce a continuous mining process. On the whole, the gold-mining industry seems to be more sensitive to general inflationary pressures than to the cost effects that are associated with depth, temperature, and water quantities pumped. Greater control is possible over physical environmental factors such as the grade of ore mined, temperature, rate and nature of development of a mine, and adaptation of the daily working cycle to a continuous mining process. Wolfe and others hold the view that the industry will lose control over labour costs as a result of the 'sharp increase in wages and the growth of Black trade unions. However, the use of more capital-intensive technology will allow the industry to reduce its labour force, and a smaller, better-trained, and more permanent labour force will enable the industry to cope with the increasingly difficult physical environment and higher wages.

Jan 1, 1987