Search Documents

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluorides1,2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02.SiO2) with the ammonium acid fluoride (NH4F.XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo¬dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By R. Zivojinovic, S. Vujic, T. Tanaskovic

The problem of determining the optimum exploitation life of machinery, namely the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Yugoslavia, the tasks of this class are very complex and difficult. To make a decision on replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, understands a management task of utmost responsibility. It requires high professional and analytical knowledge as well as the reliable arguments, based on multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution. Keywords: Bucket wheel excavators, exploitation life of machinery, optimization, operations research, theory of replacement, dynamic programming

Jan 1, 2003

Slope stability is a fundamental part of a successful mining operation. It impacts directly on the safety of personnel and the economics of the mine. The Jwaneng Mine in Botswana is planning a push back of 644m depth in the south east wall. Mining will commence in 2010 and be completed in 2024. This will put the mine in the deep pit category. The mine has invested in extensive geotechnical data gathering and design programs that started as far back as 2003 for the south east wall. The south east wail of Jwaneng Mine is characterized by foliation that dips adversely into the mining faces. The orienta1ion of the foliation is variable due to intense tectonic movements that have also caused the occurrence of faults that are sub-vertical. A considerable amount of information on the characteristics of structural patterns and the rock mass has been collected. This paper presents an overview of the feasibility level geotechnical design that is about to be concluded.

Jan 1, 2010

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By G. O. Rading, B. O. Odera, M. J. Papo, R. Couperthwaite

"Platinum-based alloys are being developed with microstructures similar to nickel-based superalloys for potential high-temperature applications in aggressive environments. Since the chemistries of nickel and platinum are similar, Pt-based alloys can be made with gamma prime ~Pt3Al precipitates in a gamma (Pt) matrix. Currently, the Pt-Al-Cr-Ru system is one of the bases for developing Pt-based alloys, where Al allows the formation of thePt3Al precipitate and also gives protection from the alumina scale formed, Cr provides oxidation resistance and stabilization for the L12~Pt3Al phase, and Ru provides solid solution strengthening in the (Pt) matrix. Four Pt-Al-Cr-Ru-V and two Pt-Al-Cr-Ru-V-Nb alloys were made, with compositions based on a quaternary alloy, ~Pt82:Al12:Cr4:Ru2, which hadpreviously been identified as having optimum properties. Four of the as-cast alloys had the targeted two-phase structure of ~Pt3Al and (Pt), and two were single-phase ~Pt3Al. Vanadium partitioned more to (Pt) than to~Pt3Al. There was an improvement in hardness compared to the quaternary alloys. The best addition of V was ~15 at.%; higher additions resulted in brittle intermetallic phases of the Pt-V system. The effect of Nbcould not be ascertained because of its high losses."

Jan 1, 2015

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipeline

Jan 1, 2007

By J. J. Cilliers, I. K. Craig, J. D. le Roux, K. Hadler

An analysis of the state-observability characteristics of a dynamic tank-to-tank model of a flotation bank indicates that the concentrate-flow rate of each tank can be estimated from accurate measurements of the pulp height in each tank and the final tailings flow-rate exiting the final tank. Therefore, there is an opportunity to construct an observer (model-based soft-sensor) which can estimate the concentrate flow-rate of tanks in a flotation bank. The concentrate flow-rate, i.e. mass pull, is generally measured by means of froth image analysers on industrial plants. A model-based soft-sensor will not only provide a means to validate froth image analyser results, but could potentially substitute them as they are less expensive to implement and maintain. Keywords: Concentrate flow-rate, estimation, flotation, modelling, observability, soft-sensor

Jan 1, 2020

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By R. G. B. Pickering

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock?though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominately by means of scraper buckets and scraper winches?these were first introduced in the 1920s. Support is still mainly rock, either in situ pillars or backfill, or alternatively wood. Just as the mining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ?trackless mechanized mining? was introduced in the early1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to ?off the shelf? equipment. The move to introduce room-and-pillar mining into the narrow UG2 reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long hole drilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds?maximum reef recovery with minimum waste dilution.

Jan 1, 2002

By R. M. Whyte

The complexities that exist in the nature of the basic feedstock to the metallurgical process call for a high degree of ingenuity from the extractive metallurgist in seeking the best possible treatment method for a particular ore. Drawing from personal experience the author presents four case studies that demonstrate the value of creative thinking in addressing the challenges typically encountered by the extraction metallurgist. It is concluded that creative expression most often occurs in response to a perceived strong need within an organization. By deliberately laying down meaningful challenges management can stimulate innovative thinking and achieve extraordinary results.

Jan 1, 2009

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By E. M. W. Skinner

Various models of near-surface kimberlite pipe emplacement have been proposed over the years. These include a top-down, phreatomagmatic model, a bottom-up, embryonic pipe model and three top-down explosive dyke models. AU of these models consider kimberlites as essentially the same rock type. However, different kimberlites have different pipe shapes and contain different rock types with very specific mineral assemblages and textures and therefore are likely to have been emplaced by different processes. Some authors have considered local geological differences as the principal reason for the contrasting geology but others argue that, while geological differences might contribute locally the petrographic peculiarities of particular kimberlites may be due mainly to inherent compositional differences specifically in the ratios of juvenile CO2 and H2O.

Jan 1, 2010

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By Henri Fredriksson, Rami Saario, Mark Weatherseed, Juri Matinheikki

"The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value. With regard to solvent extraction, the introduction of an innovative modular plant design will help to address these issues. The first such modular offering is Outotec’s VSF®X modular solvent-extraction plant that uses prefabricated and transportable modules. Reuse and recyclability have underpinned the design concept. The greatest advantage of the VSF®X modular solvent-extraction plant is its relocation possibility. Additionally, it is suitable for various metals and plant capacity is adjustable through a scalable modular structure. After a dedicated plant lifecycle, the plant can be dismantled and relocated to a new site. This reuse ability offers major benefits for short-term plants, making them more feasible due to higher residual value. A net present value analysis is made for two examples, a conventional plant with no relocation possibility and a modular movable plant with extended plant life cycle, in order to evaluate the feasibility of modular plants. Results indicate that modular plant design could offer an economical solution with the additional advantage of improved overall sustainability through its life cycle. INTRODUCTION The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value (NPV) (Mudd, 2010; Norgate & Jahanshahi, 2010) . Awareness of sustainability issues is also rising and sustainability reporting is now a key element of many companies’ public and investor relations. Major companies are now putting more effort in this area to earn legitimacy for new projects (Mudd 2010)."

Jan 1, 2015