Search Documents

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By M. W. Hildyard, M. O. Kataka

Seismic integration schemes aim to incorporate the rock mass response provided by the historical seismic activity to improve the ability of numerical models to reproduce future response to mining. Up to now, integration schemes considered the events using quasi-static models. This paper presents case studies that consider some of the seismic and modelling issues needed to extend these schemes to include the dynamic characteristics of seismic events. The ultimate aim of an automated integration scheme seems impractical for dynamic modelling. The predictions of the WAVE elastodynamic finite difference program are, however, suitable for modelling limited numbers of events to determine either the near-field velocities and damage or the effect of fractures and excavations on the far-field low frequency response. Les projets d’intégration sismique ont le but d’incorporer la réponse de la masse rocheuse à l’activité sismique historique pour améliorer la capacité des modèles numériques à reproduire la réponse future à l’exploitation minière. Jusqu’à présent, les projets d’intégration étudiaient les évènements avec des modèles quasi-statiques. L’étude présente révèle des études de cas qui considèrent certaines des questions concernant modelage et séismes qui sont nécessaires pour porter plus loin ces projets en incluant les caractéristiques dynamiques des évènements sismiques. Le but final d’un projet d’intégration automatisé semble impraticable pour la modélisation dynamique. En revanche, les prédictions du programme élastodynamique par la méthode des différences finies WAVE sont appropriées à la modélisation d’un nombre limité d’évènements de façon à déterminer soit les vitesses à petite échelle et les dommages, soit les effets des fractures et excavations sur la réponse de basse fréquence à grande échelle. Seismische Integrationsschemata zielen darauf ab, Reaktionen der Gesteinsmasse, die von den Berichten seismischer Aktivitäten stammt, zu inkorporieren um numerische Modelle in die Lage zu versetzen, künftige Antwort zum Bergbau zu reproduzieren. Bis dato betrachteten Integrationsschemata die Fälle mit quasi-statischen Modellen. Diese Arbeit stellt Fallstudien dar, die einige der seismischen und modellierenden Fragen betrachten, die benötigt werden, um diese Schemata auszuweiten, um die dynamischen Charakeristika seismischer Fälle einzuschließen. Das Endziel eines automatisierten Integrationschemas erscheint für das dynamisches Berechnen undurchführbar. Die Vorhersagen des WAVE elastodynamisch begrenzten Unterschiedprogramms sind jedoch verwendbar für das Berechnen von begrenzten Anzahlen von Fällen, um entweder die Nahfeldgeschwindigkeiten und Schaden oder den Effekt von Brüchen und Extraktionen auf der Fernfeld Niederfrequenzantwort festzustellen.

Jan 1, 2003

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By M. Rudolph, R. Tolosana-Delgado, G. van den Boogaart, M. Reuter, U. Peuker

This paper addresses the challenge to define a concept of entropy (state of order) for a textured particle system. Both the particle texture, the intergrowth respectively, and the particle size influence the order of a particle system. The smaller the particles become, the more particles form the solid system and the more permutations of the structure of the particle bed are possible. The texture within a particle is fixed, as long as it is not subjected to changes due to comminution, flocculation or agglomeration. The paper will present a definition of entropy, which is able to reflect qualitatively and quantitatively the intergrowth and the size (distribution) of the particles. Theoretical examples will show how different breakage mechanisms can be identified using the entropy definition. Furthermore, we will define the specifications for data sets to calculate the entropy of a particle system. Keywords: Milling, mineral liberation, intergrowth, statistical entropy, modelling

Jan 1, 2020

By A. Andrews

Paper written on project work carried out in partial fulfilment of MSc (Eng) degree Solid state sintered silicon carbide ceramics are used in aggressive environments as sealings. There exist data concerning corrosion, but there are only few data concerning their electrocorrosion behaviour. Therefore the electrochemical corrosion of solid state sintered silicon carbide (SSiC) ceramics has been studied at room temperature in acidic and alkaline environments by using potentiodynamic polarization measurements. The investigation showed a pronounced electrochemical corrosion in bases and acids. In HCl andHNO3pseudo-passivity features due to the formation of a thin layer of SiO2on the surface were observed, whereas in NaOH soluble silicate ions were observed, resulting in more pronounced corrosion. The microstructural observations of initial and corroded samples reveal that the residual carbon found in the microstructure do not dissolve preferentially. Keywords: Corrosion; SEM; SSiC; polarization test.

Jan 1, 2006

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 24th August, 1977. Dr M. D. G. Salamon (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : C. G. Evans, J. P. Rees, Life Fellows ; S. R. Bryant, H. MacConachie, M. Mrost, and A. W. van Zyl, Fellows; L. T. Campbell-Pitt, F. W. Collins, A. J. Duncan, I. G. Evans, F. W. Kleinschmidt, P. L. Vaughan, R. W. Wallace, and H. Wason, Members. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on 23rd March, 1977, as published in the June issue of the Journal? Agreed.

Jan 1, 1978

Analysis for pillar extraction potential (A-PEP) is an intelligent tool, which could be used as a preliminary output indicator when considering the secondary extraction of regional support pillars in the Witbank and Highveld coalfields of South Africa. The safe and economic extraction of underground coal pillars is of paramount significance and importance to the South African coalmining industry to ensure continuity of supply of this fossil fuel. Pillar extraction practices in South Africa have been responsible a significant proportion of safety and fatality statistics in relation to its relative output (less than 5 per cent of total South African coal production) and, as a result, research was undertaken in local pillar extraction operations and extended to similar operations in New South Wales, Australia to assess a way forward for pillar extraction in South Africa. It was found that, although little in the way of new technologies has emerged in this field in the recent past, significant contributions could be made in the field of risk analysis to obtain a generic design methodology for pillar extraction in South Africa. The resultant A-PEP tool to assess pillar extraction potential is based on certain physical, risk and economic factors, which combine to indicate operational success in terms of economic, health and safety attributes. At the time of A-PEP?s development there was alack of operating underground coal pillar extraction operations, which made it difficult to validate its applicability. Since then, however, A-PEP has been successfully tested and validated against two unique underground coal pillar operations, which is the discussion of this paper. One operation is situated in the Witbank coalfield and is extracting pillars, which are 20 years old and at a depth of 80 metres below surface, while the other operation is situated in the Highveld coalfield-which is extracting 6 month-old-pillars underneath a massive dolerite sill at a depth of 220 metres. A-PEP has shown that its predictive nature is consistent the workings at both operations, irrespective of their unique conditions, and as such it can be successfully used as a mine planning tool. The A-PEP mine planning tool thus represents a positive step toward an integrated approach to underground coal pillar extraction when considering legal and operational aspects, which could form the basis for legislative guidelines when considering the future of pillar extraction in South Africa.

Jan 1, 2005