Search Documents

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

Your Council has pleasure in submitting its report for the year ended 30th June, 1970. COUNCIL The following served as Office Bearers during the year under review: Messrs J. K. E. Douglas (President), V. C. Robinson and Prof D. D. Howat (Vice-Presidents), R. C. J. Goode (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Mr. R. J. Adamson, Dr. M. G. Atmore, Mr M. Barcza, Dr J. M. Bereza, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, G. W. Holl, Dr J. P. Hugo, Messrs N. A. Honnet, P. Lambooy, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Dr J. T. McIntyre, Messrs J. Meintjies, T. C. A. Meyer, J. A. Nixon, Prof R. P. Plewman, Dr R. E. Robinson, Messrs J. F. Reid, H. Simon and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of seventeen and the standing committees held 45 meetings. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R4,608 compared with R2,124 last year. This deterioration can be attributed largely to two important factors, namely an increase in secretarial fees of RI, 789 and an increase in the loss on the Journal from R2,343 to R3,508. In addition, our contribution to the expenses of the Federation of Societies of Professional Engineers increased by R607 from R549 to R1,156. The increase in secretarial fees is partly due to our increased demand for services and partly to increased salaries. In order to maintain its essential services it has been necessary for the A.S. & T.S. to increase salaries in order to keep pace with commerce and industry. With regard to the Journal, we did not expect immediate dramatic results from the changes that were effected as from the beginning of last year in the arrangements for publication. However, the improvement has been even slower in materialising than we expected. This situation is being watched carefully and we will not hesitate to make further changes if necessary. It became clear early in the year that the financial position was deteriorating and your Council decided that it was essential to meet the situation by raising subscriptions and entrance fees. At the same time it was decided that there are no grounds for a distinction between Town and Country members and that in future the scale for the compounding of subscriptions should be based on anticipated future membership, rather than past membership. These changes have had only a minor effect on the accounts under consideration. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R132 and the total fund was, therefore, increased by this amount to R4,338. The balance sheet shows that the market value of quoted shares and debentures decreased during the year from R13,059 to R6,567, while accumulated funds now amount to R17,959 compared with R22,567 last year. It will also be noted that we are holding R25,844 on behalf of the Symposium on Opencast Mining. MEMBERSHIP Twenty-eight Fellows, twenty-four Members, seventeen Graduates, twenty-five Associates and twenty-seven Students were elected during the year. Four Members were admitted to Life Membership; Five Members were transferred to the grade of Fellow; one Student was transferred to the grade of Member; two Graduates and one Student were transferred to the grade of Member; six Students were transferred to the grade of Graduate; One Associate was transferred to the grade of Fellow; One Associate was transferred to the grade of Graduate. One Fellow, one Member, six Graduates, four Affiliates and ten Students were removed from the Membership Roll in terms of by-law 7.7.1. Your Council records with deep regret the death during the year, of the following: R. A. H. Flugge-de-Smidt, C. S. McLean, Dr H. J. van Eck, (Honorary Life Fellows), J. C. Humphreys, O. Lazar (Life Fellows), D. G. Beadle, J. G. Craig, P. U. Fisher, R. G. McConnell, J. H. Moore, S. Sterling, L. R. Ulyate (Fellows), H. H. Burger, E. A C. Dickson, R. Jack, S. Ring (Members), M. J. Worrall (Graduate). A comparative statement of the membership as at 30th June, 1970, and the end of the previous year is shown in the following tabulation: 30th June 30th June Honorary Life Fellows 10 8 Honorary Fellows 6 6 Life Fellows 189 191 Fellows 514 530 Members 448 465 Graduates 68 80 Associates 155 172 Students 162 161 1,552 1,613 RECLASSIFICATION OF MEMBERSHIP The designations of grades of membership were altered to accord with the practice in professional institutes both here and overseas and members were advised of the new classifications. MEMBERSHIP DRIVE A committee was established to organise a drive for membership as it was felt that there are numbers of persons in our mining and metallurgical industries who are not yet members but who qualify for membership. Members of the committee were allocated responsibility for campaigning in sections of industry and for publicising the aims, objectives and advantages of belonging to the Institute.

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003

By R. Dippenaar

Traditionally, iron ore has been reduced with coke in a blast furnace and the hot-metal product of the blast furnace containing carbon, manganese, silicon, sulphur and phosphorous, was subsequently refined in a steelmaking furnace. During iron making as well as during steelmaking, significant amounts of slag are produced. Two decades ago, more than 13 m tonne of blast furnace slag and 4 m tonne of steelmaking slag per annum were produced in the USA alone. It is, therefore, not surprising that many attempts have been made to re-use iron and steelmaking slags. However, these slags are not merely metallurgical waste products but, on the contrary, their compositions and physical properties are judiciously designed to optimize the operations in the respective metallurgical reactors. The variation in composition and properties of blast furnaces lags are largely determined by the gangue in the ore and ash in the coke and much progress has been made in the re-use of such slag. With respect to steelmaking slag, emphasis has in recent years been placed on hot-metal treatment before refining and ladle treatment after decarburization. The bulk removal of silicon, phosphorous and sulphur from the hot-metal product of the blast furnace by specially designed slags prior to refining in a basic oxygen furnace, has reduced tap-to-tap time, lowered cost and produced steel of much higher quality. The use of synthetic slags in ladle refining techniques subsequent to decarburization in the basic oxygen furnace has resulted in reduced hydrogen and nitrogen contents and reduced solute impurities. Moreover, inclusion shape and composition control, again by the use of specially designed slags has led to the achievement of much improved mechanical properties of the steel. In these revised process routes, slag of different compositions are produced in the variety of unit processes and hence the re-use of steelmaking slags has become much more complex. Clearly, a thorough understanding of the design and use of these different slags is a pre-requisite to the development of re-use strategies. Japanese steelmakers have spearheaded attempts to reduce slag volumes in the individual unit processes and to strive towards ‘slagless steelmaking’ by recycling slags internally. Steelmaking slag volumes have been reduced on commercial scale from about 140 kg/tonne steel to 60kg/tonne steel. Moreover, model predictions have shown that, in principle, all slag can be recycled and the phosphorous extracted to produce fertilizer. This development is of particular significance since the supply of low-phosphorous iron ores is diminishing at an ever increasing rate. Keywords: slag, environment, iron, steel,

Jan 1, 2004

By B. K. Loveday

There are certain ores that can be treated without upgrading (e.g., gold and uranium ores), and upgrading needs to be considered only for fairly low-grade ores of this type. If the grade is very low, treatment will not be economic even with upgrading, and there is therefore a limited range of ore grades for which upgrading is suitable.

Jan 1, 1980

By Z. Szczepanik, D. Milne, K. Kostakis

Abstract This paper presents the results of a series of creep tests performed on a total of nine samples of Lac du Bonnet granite from the Underground Research Laboratory near Pinawa, Canada. Each of the nine samples were subjected to stresses in excess of 80% of the average uniaxial compressive strength of the granite and were maintained at that level of constant loading for periods of time ranging between a few minutes and several months. Acoustic emission was recorded in order to monitor the development and accumulation of brittle microfracture damage in the samples throughout the long-term loading. According to previously published theoretical predictions and field results, as well as similar experimental results of creep tests in granite, samples should fail when loaded to 70% of their UCS for an extended period of time. Six of the samples did not fail when subjected to stresses in excess of 80% of their UCS over periods of several months and were subsequently subjected to uniaxial compression to failure. The average strength of the samples that had previously been subjected to long-term loading were comparable to the average published strength of this rock. Three of the nine samples had increased end confinement and these three samples failed under long term loading. Résumé Cet article présente les résultats d&apos;une série d&apos;essais de fluage de roche exécutés sur neuf échantillons de granite de Lac du Bonnet, du laboratoire souterrain de recherches près de Pinawa, Canada. Chacun des neuf échantillons a été alors soumis aux charges au-dessus de 80% de la résistance à la UCS moyenne du granit et a été maintenu à ce niveau du chargement constant pendant des périodes s&apos;étendant entre quelques minutes et plusieurs mois. L&apos;émission acoustique a été enregistrée pendant les essais afin d&apos;obtenir des indications des dommages pendant le chargement à long terme. Selon des résultats théoriques précédemment édités et les résultats expérimentaux semblables des essais à long terme en granite, échantillons devrait échouer si chargé à 70% de leur UCS pendant une période prolongée. Six des échantillons n&apos;ont pas cassé quant ils ont été soumis aux charges au-dessus de 80% de leur UCS et ont été plus tard soumis à la compression uniaxiale à la rupture. La force moyenne des échantillons qui avaient été précédemment soumis au chargement à long terme étaient comparable à la force éditée moyenne de cette roche. Trois des neuf échantillons avaient augmenté le confinement de fin et ces trois échantillons ont cassé sous le chargement à long terme. Zusammenfassung Dieser Artikel beschreibt die Resultate von Kriechversuchen, die an neun Proben aus dem Lac du Bonnet Granit des "Underground Research Laboratory" bei Pinawa in Kanada durchgeführt wurden. Jede der neun Proben wurde Drücken unterworfen, die mehr als 80% der einaxialen Druckfestigkeit des Granites entsprechen. Diese Drücke wurden für verschiedene Zeitspannen von wenigen Minuten bis zu einigen Monaten auf einem konstanten Niveau gehalten. Während der gesamten Langzeitbelastung wurden akustische Emissionen aufgezeichnet, um die Entwicklung und gesamthafte Beschädigung der Proben durch Sprödbruch aufzuzeichnen. Entsprechend bisher veröffentlichter theoretischer Vorhersagen, Feldversuchen und auch experimentellen Resultaten von Kriechversuchen an Granitproben wäre ein Versagen der Proben zu erwarten gewesen, wenn sie über längere Zeit einer Last von 70% ihrer einaxialen Druckfestigkeit unterworfen werden. Wider Erwarten trat bei sechs der Proben kein Versagen ein, als sie mit über 80% ihrer einaxialen Druckfestigkeit über mehrere Monate belastet wurden; daher wurden sie im Anschluss bei einaxialer Kompression zum Versagen gebracht. Die mittleren Festigkeiten der im Langzeittest verwendeten Proben sind vergleichbar mit den normalerweise für diesen Gesteinstyp angegebenen Festigkeiten. Drei der neun Proben versagten unter der Langzeitbelastung; diese drei Proben hatten eine erhöhte Endflächenreibung.

Jan 1, 2003

By J. A. L. Napier, J. S. Kuijpers

SYNOPSIS This paper demonstrates that the horizontal stresses induced by the creation of a tabular scope in a single mining step are always tensile at the centre of the stope span, but that compressive stresses are actively generated in hangingwalls and footwalls during sequential mining. A stress-distribution mechanism is introduced, and is used to explain the results for elastic behaviour, and for inelastic behaviour both during a single mining step and during multiple mining steps.

Jan 1, 1991

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By Willem C. A. van Niekerk, David A. Baldwin, Nardus Potgieter, Willie A. Gericke

Authorities that regulate environmental issues pertaining to industrial wastes in South Africa regard landfill disposal as the only effective environmental management option for slag and other inorganic by-products from the ferro-alloy industry. Metallurgical slags are widely utilised in civil engineering and construction applications in other countries in the world and in line with the overall philosophy of conserving mineral and other natural resources, these materials should be assessed for the possibility of resource recovery, recycling, reclamation, direct re-use or alternative uses. This presentation describes a risk-based approach for the assessment of by-products from the ferro-alloy industry for alternative use. Once a by-product from an industrial process has been identified for alternative use, its intended use would be defined, but it will not be possible to control its actual use or misuse in society, nor will it be possible to control its fate during the application life cycle. In the interest of protection of human health and the environment, potential risks associated with the handling and uses of a material throughout its life cycle therefore have to be quantified. The assessment has to include both human health and ecological risks and must cover the entire life cycle of a product, from its production up to its end-of-life disposal. The presentation introduces the concept of tiered risk assessment and demonstrates how this applies in the overall assessment of by-products from metallurgical industry sector for safe use in society.

Jan 1, 2007

By M. G. Spengler

A new type of pack has been developed primarily for the support of narrow stopes. It was shown in the laboratory that it has characteristics that very closely approximate the optimum required by underground support to achieve hangingwall stability.

Jan 1, 1978

By D. W. Horsfall

This paper reviews the properties and uses of mixtures of coal with fuel oil, methanol, or water, emphasis being placed on mixtures of coal and water. The material presented is taken from studies conducted overseas, and it is recommended that similar studies should be conducted on mixtures containing South African coals, which differ from the coals of the northern hemisphere

Jan 1, 1990

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By J. Lamb

Project managers must juggle many aspects to bring their project in on time, on budget, and in accordance with the aims of the project owner. Whether the project is a mining feasibility study, a technology implementation or a construction project, it falls to the project manager and his or her team to deal with risk from two standpoints, which may be at odds with one another. First, a project team must deal with risks to the project itself - that is, risks to on-time, on-spec and on-budget delivery against the value promise made to the customer. Second, there is the management of risks within the subject matter of the project, undertaken on behalf of the customer. The project manager cannot dodge this responsibility; yet there is a tendency (particularly in smaller, in-house studies) to avoid digging too deep, possibly for fear of what may be uncovered! This paper investigates the responsibilities of project teams in regard to risk management and reporting. It examines ownership of project risk; the nature of risk management activities undertaken by the team during the course of a project; and outlines some controls to ensure that the two opposing arms of project risk are reconciled for the benefit of both the project team and the project owner.

Jan 1, 2007

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By R. S. Sarracino, M. J. Louw, S. M. Vather

Two detonation models, IDeX for ideal VOD and CPeX for non-ideal VOD, were used to predict the velocities of detonation (VOD) of five explosives: ANFO, a bulk emulsion, and three repumpable emulsions (R100 Gold, R100 Diamond, and R105). The theoretical VODs were compared with the in-hole VODs of the explosives, and the predicted and actual values were found to be within experimental error for ANFO and the bulk emulsion. The results were not consistent for the repumpable emulsions. The discrepancies can be explained as being due to variations in mining and loading practices. The results show that the detonation models can be effective tools in predicting the behaviour of explosives in different diameters and rock confinements, provided that the user is aware of the factors that can affect the optimal usage of explosives and equipment.

Jan 1, 1993

By L. Andrews

Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution for the problem. Mineralogical techniques are described for various pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By L. C. Woollacott

A computer-aid is described that is designed to calculate steady-state material balances for ore-dressing circuits. The program determines the material balance from a specification of the process condition. No mathematical models or data adjustment techniques are employed. As such the program complements existing simulation and material balance &apos;smoothing&apos; packages. The process condition is specified using performance indicators. These are significant parameters in the industry with which all practising mineral processors are very familiar. The program employs an equation-oriented technique for material balancing and so has had to deal with the difficulties peculiar to that approach.

Jan 1, 1987

By R. H. Matjie, J. R. Bunt, C. A. Strydom

"A number of conventional and advanced analytical techniques (proximate and ultimate analysis, low-temperature oxygen-plasma ashing, X-ray diffraction, X-ray fluorescence spectrometry, coal petrography, and lightelement electron microprobe analysis) have been integrated and crosschecked to provide detailed characterization of coals from the Highveld coalfield in South Africa, as a basis for better understanding of the mineralogical and chemical properties of the individual coal sources that are blended as feedstocks for combustion and carbon conversion processes. The techniques included methods to quantify the abundance and composition of the mineral matter (minerals and non-mineral inorganic elements), and also the abundance and chemical composition of the individual macerals in the individual coals concerned.Kaolinite is the most abundant of the minerals in the coals studied, with lesser but still significant proportions of quartz, mica and/or illite, dolomite, calcite, and pyrite. Small but variable proportions of anatase, goyazite, and siderite are present in some coal samples. Electron microprobe analysis, based on a special configuration for light-element study, shows that the vitrinite contains less carbon and more oxygen, and has significantly higher concentrations of nitrogen and organic sulphur, than the inertinite macerals in the same samples. Minor proportions of organically-associated inorganic elements, including titanium, were also identified in some of the maceral components.A comprehensive knowledge of the minerals and non-mineral inorganic elements in the coals used for feedstock preparation, obtained by integration of data from these advanced analytical techniques with more conventional analyses, may be of benefit in understanding the processes that take place during coal utilization, and also in avoiding or ameliorating some of the operational and environmental problems that may occur in different sectors of the coal utilization industry."

Jan 1, 2016

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006